Summary of the content on the page No. 1
The
PST-10D
Owners Manual
1
Summary of the content on the page No. 2
Introduction Thank you for purchasing the Furman Power Station-10D Power Conditioner. For over 30 years, Furman has pioneered the development of AC power products for the most demanding audio, video, and broadcast professionals. Furman’s Series Mode Protection Plus (SMP+), Linear Filtering Technology, and Digital-HD Television Ready circuitry delivers the purest AC power and the most comprehensive protection available – going far beyond what is found in both traditional and multi-stag
Summary of the content on the page No. 3
enclosure. Do not remove the covers. There are no user serviceable parts inside. Refer servicing to qualified personnel only. Important Safety Instructions 1. Please read and observe all safety and operating instructions before installing your Power Station-10D (PST-10D). Retain these instructions for future reference. 2. Your PST-10D should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool, etc. 3. Do not place
Summary of the content on the page No. 4
7. Your PST-10D should be serviced by qualified service personnel when: • The power supply cord or the plug has been frayed, kinked, or cut. • Objects have fallen or liquid has spilled into the unit. • The unit has been exposed to rain or other moisture. • The unit does not appear to operate normally, exhibits a marked change in performance, or the Protection OK indicator is not lit. • The unit has been dropped, or the enclosure damaged. 8. Your PST-10D requires that a safety ground be present f
Summary of the content on the page No. 5
contaminating an adjacent unit. For example, a television plugged into the digital – video filtered outlets will not affect an audio receiver- controller connected to one of the PST-10D’s standard or delayed outlets. Delayed AC Outlets – Trigger Switch and 12VDC inlet: The PST-10D features (3) delayed AC outlets. Today’s Home Theater and Home Recording- Studio components rarely require delayed soft-start from an external AC outlet because their circuits feature soft-start turn-on. Del
Summary of the content on the page No. 6
Telco – Satellite – Cable Transient Voltage Surge Suppressors: The PST-10D features transient voltage surge suppression for both standard telephone lines, as well as cable and satellite lines utilizing standard coaxial connectors. As these surge suppressors are in- line, they will require an additional cable to connect from their output to the control device requiring protection. All in-line surge suppressors feature our exclusive ground contamination free technology. This aids in eliminat
Summary of the content on the page No. 7
and out going cable from the PST-10D. Connect the incoming connector to the component that formerly received the out going connector, thus by-passing the in-line protection. If the signal is present (but not when used with the PST-10D’s) then the protection circuit is damaged (assuming it worked properly before the storm or catastrophic event). Circuit Breaker If the PST10D is connected to an AC outlet where sufficient voltage is present, the unit should operate properly wi
Summary of the content on the page No. 8
voltage in excess of 137VAC is sensed, either on initial power-up or during normal operation, the PST-10D will shut off power and this indicator will light. NOTE: If the mains power is above the high cutoff voltage and has caused the unit to remove power from its outlets, it can not restore power without the operator manually turning the unit off, then on again. Avoid turning the unit back on without first checking the source of the problem and perhaps changing the AC source. Protection OK
Summary of the content on the page No. 9
distance from the two mounting hole drilled into your wall, rack or cabinet surface. Once the screw is fastened flush with the surface, back it out approximately ½” . The screw head should push through the crossed cutout on the bottom surface of the Power Station. Next, simply allow the Power Station to move down and seat into the end of its oval cut-out. Adjust the pan head screw if necessary. Warranty To Register for the following warranty please visit Furman’s website at www.
Summary of the content on the page No. 10
Return shipping charges back to purchaser will be paid by Furman. CONNECTED EQUIPMENT WARRANTY: Furman Sound’s Connected Equipment Warranty covers equipment that is damaged by transient voltage (an “Occurrence”) while properly connected through the Furman PST-10D to a properly wired AC power line with a protective ground in an indoor location. Furman’s Connected Equipment Warranty is limited to the amount of the deductible on the Purchaser’s personal property insurance policy up to $500.00.
Summary of the content on the page No. 11
prong adapters, or extension cords. Any such installation voids this warranty. The Furman warranty only protects against damage to properly connected equipment where Furman has determined, at its sole discretion, that the damage resulted from an Occurrence and does not protect against acts of God (other than lightning) such as flood, earthquake, war, terrorism, vandalism, theft, normal-use wear and tear, erosion, depletion, obsolescence, abuse, damage due to low- voltage disturbances (i.e. b
Summary of the content on the page No. 12
STATEMENTS DO NOT CONSTITUTE WARRANTIES, shall not be relied upon by purchaser, and are not a part of the contract for sale or this limited warranty. This Limited Warranty states the entire obligation of Furman with respect to the product. If any part of this Limited Warranty is determined to be void or illegal, the remainder shall remain in full force and effect. Warranty claims should be accompanied by a copy of the original purchase invoice showing the date of purchase (if a Warranty Reg
