Summary of the content on the page No. 1
ELECTRIC PAINT
SPRAY GUN
Model 47274
ASSEMBLY and OPERATING
INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2002 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Summary of the content on the page No. 2
Specifications E222975 Power Supply 110 V, 60 Hz, 80 Watts Container Capacity 33 Ounces Maximum Pressure 1450 PSI / 100 Bar - Flow Rate = 5.1 GPH Maximum Viscosity 30 (Seconds) Refer to page 5 (test). Handle Length 5 Inches Gun Dimensions 9-1/2” H x 4-1/2” W (weight = 3 Lbs.) Accessories: Viscosity Cup with hanger/ Four Nozzle Tips including 2 - .032”, 1 - .021”, 1 - Extended Tip - .021”, / Angled Nozzle Adapter (50 Degree) Save This Manual You will need the manual for the safety warnings and p
Summary of the content on the page No. 3
8. Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear an ANSI approved respirator when working around metal, wood, and chemical dusts, mists, paints, oils, sealers, and stains. 9. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines. 10. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically a
Summary of the content on the page No. 4
- Stains, oil-based paints, thinners, sealers, and water-proofers. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as respirators that are specially designed to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq. ) Note: Performance of this tool (if powered by line voltage) may vary depending on varia
Summary of the content on the page No. 5
Operation Regulator Knob Pump Locknut Round Jet Tip Trigger Power Cord Pump Housing Container 1. Before loading the Container (17) with material, check the viscosity of the material. 2. Dip the Viscosity Cup into the material, and time how long it takes for the material to completely run out of the cup (See FIGURE 1). The longer it takes, the higher the viscosity. 3. In general, most materials work adequately if the viscosity is FIGURE 1 between 15 and 30 seconds. 4. If the viscosity is too hig
Summary of the content on the page No. 6
Operation (continued) Warning!! Makes sure the Spray Gun is unplugged from the power source and your finger is off of the Trigger (#19) when adjusting or changing Nozzle Tips (#11). 6. Attach the appropriate Nozzle Tip (11). The Spray Gun comes with: (2) @ .032” - For latex stain and oil based paints, heavy bodies (1) @ .021” - For light bodies, stains, sealers, and water-proofers (1) @ .021” - (Extended Tip) For lighter bodies, stains, sealers, and water-proofers 7. To attach a new Nozzle T
Summary of the content on the page No. 7
Operation (continued) Proper Spraying Techniques (continued). FIGURE 5 From a distance of 12 inches, keep your arm extended with your elbow locked. This will insure you maintain the correct distance more accurately. Squeeze the Trigger (#19) and move the Spray Gun evenly and steadily. Use an established pattern for each pass as shown in FIGURE 5. Breaking up your pass will result in irregular surface patterns. At the end of each pass, release the Trigger (#19) for a second to prepare for th
Summary of the content on the page No. 8
Parts List Parts No. Description 1 Power Cord 2 Grommet 3 Terminal Board 4 Switch 5 Housing Half Shells 6 Leaf Spring 7 Armature 8 Shock Absorber 9 Drive Housing 10 Valve 11 Nozzle Set* 12 Locknut Note: Replacement 13 Cylinder Cylinders (#13) are 14 Piston Spring available in a 4 pack 15 Piston SKU #47366. 16 Suction Tube 17 Container 18 Lid / Pump Housing 19 Trigger 20 Switch Spring 21 Brand Plate 22 Housing Half Shells 23 Screw 24 Spring 25 Regulator 26 Strain Relief 27 Screw 28 Filter 2
Summary of the content on the page No. 9
29 Assembly Drawing Nozzle Set (#11) includes 2 - .032”, 1 - .021”, 1 - Extended Tip - .021”, / Angled Nozzle Adapter (not shown on Assembly Drawing). SKU 47274 For technical questions, please call 1-800-444-3353. Page 9
