Summary of the content on the page No. 1
Operator's Manual
®
S
Mode_ No. 486.24276
/
/
/
!
/
/
CAUTION:
,, Safety
Before using this product, read
,, AssembLy
this manuaUand follow aH Safety
,, Operation
RuUesand Operating Instructions.
,, Maintenance
,, Parts
mMPORTANT: For Missing Parts or
AssembUy Questions Call 1-866-576-8388
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www=sears=com/craftsman
PRINTED IN U.S.A. FORM NO. 49952 (11/05)
Summary of the content on the page No. 2
MAINTENANCE/STORAGE ............................................ 9 SAFETY RULES .............................................................. 2 FULL SIZE HARDWARE CHART .................................... 3 REPAIR PARTS ILLUSTRATION .................................. 10 CARTON CONTENTS ..................................................... 4 REPAIR PARTS LiST .................................................... 11 ASSEMBLY ...................................................................... 5
Summary of the content on the page No. 3
SHOWN FULL SIZE NOT SHOWN FULL SIZE _A .F J / G / C H /L \ _j.f D I I, i / \ x\\ _ jE /t RE[:. DESCRIPTION DESCRIPTION QTY. REF.[ QTY. A 4 Carriage Bolt, 5/16" x 2o3/4" G i 5 Nylock Nut, 5/16" H i 4 B 6 Flat Washer, 5/16" Carriage Bolt, 5/16 x 2" C 1 Hex Bolt, 5/16" x 2" Carriage Bolt, 1/4 x 1" D 4 J i 4 Hex Bolt, 1/4 x 1ol/2" Spacer E 2 K i 4 Adhesive Pad Hex Bolt, 5/16 x 1" L i 2 F 5 Plastic Knob Nylock Nut, 1/4" i
Summary of the content on the page No. 4
1. Upperbasetube 8. LeftSupport Bracket 9. BaseBracket 2. TopTubes (2) 10.LeftBaseBracket 3. BaseLegTubes (2) 4. BaseLegTube(Flattened 11.RightBaseBracket (stamped withR) 12.U=Tube 5. FrontBraceRod 6. Upright Tubes (2) 13.VinylCanopy 7. RightSupport Bracket 14.SupportRods(3) F:_/4 6 J8 12 11 J 14 13 \
Summary of the content on the page No. 5
TOOLS REQUIRED FOR ASSEMBLY iNSTRUCTiONS FORTRACTORS WITH SINGLE SUSPENSION BRACKET (2) 7/16" Wrenches (2) 1/2" Wrench STEP 2: (SEE FIGURE2) (1) 1/2" or 9/16" Socket Wrench , The four holes in the base bracket are unequal in height, Place the base bracket on a flat surface with the holes that are higher facing away from you, REMOVAL OF PARTS FROM CARTON , Attach the right side of the base bracket to the middle two holes in the flattened base leg tube using two Remove all parts and hardware packa
Summary of the content on the page No. 6
INSTRUCTIONS FOR TRACTORS WiTH DUAL STEP 3: (SEE FIGURE 3) , insert the ends of the base leg tubes into the upper SUSPENSION BRACKETS base tube, UPPER BASE TUBE STEP 5: (SEE FIGURE 5) Attach the right base bracket to the front holes of a base leg tube that does not have a flattened end, using two 5/16" x 2o3/4" carriage bolts (A), two ] spacers (J) and two 5/16" nylock nuts (G). Make onty LJ finger tight. Repeat for the left base bracket. ]J i ] 5/16" NYLOCK NUT (G) SPACER (J) / 5/16" x 2o3/4" B
Summary of the content on the page No. 7
COMPLETING ASSEMBLY - ALL TRACTORS STEP 7: (SEE FIGURE 7) , Raise the tractor seat and remove the springs and bolts from the rear fender using a 1/2" socket for GT STEP 8: (SEE FIGURE 8) tractors or a 9/16" socket for LT tractors. , Assemble the upright tubes to the base assembly , Place the base tube assembly onto the rear fender. using a 5/16-18 x 2" carriage bolt (B), 5/16" flat Align the front or rear slot in the base brackets with washer (H) and plastic knob (L) for each tube. the spring mo
Summary of the content on the page No. 8
STEP 10: (SEE FIGURE 10) STEP 11: (SEE FIGURE 11) , Raise the tractor's hood. , With the tractor's hood still raised, place the snow cab , insert the ends of the front brace rod into the inner set canopy onto the tubing frame and drape the front flap of holes in the U-tube and rest the bottom of the brace down in front of the tractor% dash panel. Lower the rod on the dash pane!. If the brace rod is too long to hood, trapping the front flap under the hood. Secure rest on the dash panel, you can s
Summary of the content on the page No. 9
Readthis owner's manual and safety rules before operating your tractor with the snow cab. CAUTION: This snow cab does not Check the area of operation thoroughly before using provide protection against exhaust fumes, the tractor with the snow cab. The added height of the collision, rollover or other accidents. snow cab and a reduced field of vision require extra caution during operation. Remove the upper snow cab frame and canopy before CAUTmON: Watch out for low tree limbs you transport the trac
Summary of the content on the page No. 10
REPAIR PARTS FOR MODEL 486.24276 SNOW CAB 3 \\\ \ \\ \ \ 3 / /, 4 / 11 15 J 2 2 l 14 l 1 9 f 25 13 \ \\ 16 \ 22 / 21 ...... 18 26 23 \ 19 lO
Summary of the content on the page No. 11
REPAIR PARTS FOR MODEL 486.24276 SNOW CAB RER PART QTY. DESCRiPTiON RER PART QTY. DESCRiPTiON NO. NO. NO. NO. 1 1 Front Brace Rod 49242 1 Top Base leg tube 15 25795 2 2 25014 2 Upright Tube 16 49325 Base Leg Tube 3 1 25013 2 Top Tube 17 40003 Base Leg Tube, Flattened 4 25012 1 U-Tube 18 25302 1 Right Base Bracket 5 1 Left Base Bracket 25015 3 Support Rod 19 25303 6 1 48738 1 Vinyl Canopy 20 25835 Right Support Bracket 7 1 23658 4 Spacer 21 25794 Left Support Bracket 8 1 43720 2 Plastic Knob 22 2
Summary of the content on the page No. 12
_ililijjjjjjjjjjjjjjjjjjjjj!! You r Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! iiiiiiiiiHHHHi For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. iiiiiiiiiiiiiiiiii 1-800-4-MY-H 0 M E® (1-8oo 469-4663 ) Oa,, an_t,_o, da_ o_ o,o_t
