Summary of the content on the page No. 1
MODEL GFC7000EU CO ANALYZER WITH AUTO-REFERENCE
(Addendum to GFC7000E Manual PN 04584)
MODEL GFC7000EU
CO ANALYZER
2
(Addendum to GFC7000E Manual PN 04584)
Teledyne Analytical Instruments
16830 Chestnut St.
City of Industry, Ca. 91748
TEL: 626-961-9221
FAX: 626-961-2538
TEL: 626-934-1500
E-MAIL: ai-customerservice@teledyne.com
WEB SITE: http://www.teledyne-ai.com
1
05134 Rev -
Summary of the content on the page No. 2
MODEL GFC7000EU CO ANALYZER WITH AUTO-REFERENCE (Addendum to GFC7000E Manual PN 04584) OVERVIEW The model GFC7000EU is a close derivative of the Model GFC7000E CO Analyzer. The optical bench is longer (14 m), making the instrument more sensitive at low CO 2 levels. The instrument has a user selectable full scale range of 0-100 PPB to 0-100 PPM of CO . 2 The instrument does not come equipped with a sample flow rate sensor. Hence, disregard any reference to the flow sensor in the users manual.
Summary of the content on the page No. 3
MODEL GFC7000EU CO ANALYZER WITH AUTO-REFERENCE (Addendum to GFC7000E Manual PN 04584) Humidity Range 0-95% RH, Non-Condensing (6) Temp Coefficient < 0.05 % of reading per °C (5 ppb/°C minimum) Voltage Coefficient < 0.05 % of reading per V Dimensions 7" x 17" x 23.5" (178 mm x 432 mm x 597 mm) (HxWxD) Weight 50 lb (22.7 kg) AC Power 100V 50/60 Hz (3.25A), 115 V 60 Hz (3.0A), 220 – 240 V 50/60 Hz (2.5A) Environmental Installation Category (Over voltage Category) II Conditions Pollution Degree 2
Summary of the content on the page No. 4
MODEL GFC7000EU CO ANALYZER WITH AUTO-REFERENCE (Addendum to GFC7000E Manual PN 04584) There are 4 relay alarm outputs (AL1-AL4) on the rear panel. AL1 is for system okay, AL2 is for concentration limit 1 exceeded and AL3 is for concentration limit 2 exceeded. The relay alarm output AL1 is enabled all the time, whereas the AL2 and AL3 can be enabled/disabled by going into the diagnostics menu (with 929 password), then factory options, then turning conc. Alarm Relays ON or OFF. When the concent
Summary of the content on the page No. 5
MODEL GFC7000EU CO ANALYZER WITH AUTO-REFERENCE (Addendum to GFC7000E Manual PN 04584) SAMPLE WHEEL TEMP WARNING CO = XX.XX TEST deactivates Warning Messages until New warning(s) TEST CAL MSG CLR SETUP are activated MSG activates Warning SAMPLE RANGE=50.0 PPM CO = XX.XX Messages. keys replaced with < TST TST > CAL MSG CLR SETUP TEST key All Warning messages are hidden, but MSG button appears SAMPLE WH
Summary of the content on the page No. 6
MODEL GFC7000EU CO ANALYZER WITH AUTO-REFERENCE (Addendum to GFC7000E Manual PN 04584) Warning Fault Condition Possible Causes Message FRONT PANEL The CPU is unable to WARNING only appears on Serial I/O COM Port(s) WARN Communicate with Front Panel Display will be frozen, blank or will not the Front Panel respond. Display /Keyboard Failed Keyboard 2 I C Bus failure Loose Connector/Wiring Failed IR Photo-Detector PHOTO TEMP PHT DRIVE is Failed Sync/Demod Board WARNING >4750 mVDC or
Summary of the content on the page No. 7
MODEL GFC7000EU CO ANALYZER WITH AUTO-REFERENCE (Addendum to GFC7000E Manual PN 04584) Warning Fault Condition Possible Causes Message on wheel rotation. Failed Sync/Demod Board If Status LED’s on the Sync/Demod Board ARE flashing the cause is most likely an a problem with the analyzer’s main power: Intermittent loss of the power supply too short to cause a SYSTEM RESET warning; Frequency problem with the AC Mains. SYSTEM RESET The computer has This message occurs at power on. rebooted.
Summary of the content on the page No. 8
MODEL GFC7000EU CO ANALYZER WITH AUTO-REFERENCE (Addendum to GFC7000E Manual PN 04584) #N05ATI 009690000 Filter, TFE, 47 mm 5 um, Qty 100 009690100 Filter, TFE, 47 mm 5 um, Qty 25 009820200 Assy, Motor, Synchronous, 115V/60HZ, "E" 010790000 Input Mirror 010800000 Output Mirror 016290000 Window, Sample Filter, 47 mm 016910000 Akit, Catalyst, CO/CO2 Converter (1 OZ) 019340000 Sample Thermistor M400 (S/N >099) or M401 (S/N>0573) 024710000 Tubing: 6', 1/8"CLR 024720000 Tubing: 6', 1/8" BLK 024750
Summary of the content on the page No. 9
MODEL GFC7000EU CO ANALYZER WITH AUTO-REFERENCE (Addendum to GFC7000E Manual PN 04584) OR0000001 O-Ring, Flow Control OR0000058 O-Ring, Sample Filter, 47 mm, 2-228V OR0000034 O-Ring, Input/Output Mirror/Detector OR0000039 O-Ring, Window OR0000041 O-Ring, Field and Objective Mirror 043590100 Pump, 115V 50/60 Hz PU0000022 Pump Rebuild Kit, KNF Model #N05ATI PS0000025 Power Supply, +12V PS0000011 Power Supply, +5/+- 15V 042680000 Solenoid, Stainless Steel, 3-Way, 12V 042690000 Solenoid, Stainless
