Summary of the content on the page No. 1
p SS 250
ORBIT AL SANDER
Oper ation and Safety Notes
6
35324_ORBITAL SANDER_Cover_LB6.indd 2 21.07.09 14:44
Summary of the content on the page No. 2
Bef ore reading, unfold the page containing the illustrations and familiarise yourself with all functions of the de vice. GB / IE / CY Operation and Safety Notes Page 5 35324_ORBITAL SANDER_Cover_LB6.indd 3 21.07.09 14:44
Summary of the content on the page No. 3
1 2 11 3 10 4 5 6 6 8 7 a b C 9 D e F 12 35324_ORBITAL SANDER_Cover_LB6.indd 4 21.07.09 14:44
Summary of the content on the page No. 4
Table of contents Introduction Intended use ..................................................................................................................Page 6 Features..........................................................................................................................Page 6 Delivery contents ...........................................................................................................Page 6 Technical Data ...................................................
Summary of the content on the page No. 5
Introduction The following pictograms are used in these operating instructions / on the device: Wear hearing protection, dust protection Read instruction manual! mask, protective glasses and protective gloves. Observe caution and safety notes! Safety class II Caution – electric shock! Keep children away from electrical Danger to life! power tools! Risk of loss of life by electric shock from Risk of explosion! damaged mains lead or mains plug! Protect electrical power tools from Risk of fire
Summary of the content on the page No. 6
Introduction / General safety advice for electrical power tools Q Technical Data G eneral safety advice for electrical power tools Nominal voltage: 230 V 50 Hz ~ Nominal power: 250 W War NING! r ead all the safety advice Idle speed: n 7.000 - 12.000 rpm and instructions! Failure to observe the safety 0 Idle oscillation speed: n 14.000 - 24.000 rpm advice and instructions may result in electric shock, 0 Sanding sheet dimensions: Hook and loop fastening fire and / or serious injury. 93 x
Summary of the content on the page No. 7
General safety advice for electrical power tools b) a void touching earthed surfaces such c) a void unintentional operation of as pipes, radiators, ovens and refrig- the device. Check that the electrical erators with any part of your body. power tool is switched off before you There is an increased risk of electric shock if connect it to the mains, pick it up or your body is earthed. carry it. Accidents can happen if you carry c) K eep the device away from rain or the device with your finge
Summary of the content on the page No. 8
General safety advice for electrical power tools d) When no t in use always ensure that J a lways run the power cord away electrical power tools are kept out of from the appliance to the rear. reach of children. Do not let anyone use J D aNGEr OF FIr E Fr OM FLyING the device if he or she is not familiar SPar KS! Abrading metal creates with it or has not read the instructions flying sparks. For this reason, always and advice. Electrical power tools are danger- make sure that nobody is plac
Summary of the content on the page No. 9
General safety advice for electrical power tools / Operation Operation Q a stop before setting down the oscil- Setting the oscillation speed lating sander. J a lways pull the power plug out of the You can set the desired oscillation speed as 10 socket for all work pauses, before any needed with the oscillation speed selector . work on the appliance (e.g. changing The required oscillation speed depends on the the sanding paper) and when not in use. material being worked and can be determined
Summary of the content on the page No. 10
Operation Q metals or metal objects left in wood. This can hap- Instructions, tips and tricks pen especially if the wood dust has paint particles on it or is mixed with other chemical substances j Move the oscillating sander parallel, in flat and the sanded material is hot after extensive circles or alternating between lengthwise and working. You should therefore avoid overheating side-to-side motions. of products being sanded as well as the appliance j Do no t press down with the oscillatin
Summary of the content on the page No. 11
Maintenance and cleaning / Service centre / Warranty / Disposal Q Maintenance and Cleaning The warranty covers only material or manufactur- ing faults, not normal wear or damage to fragile War NING! DaNGEr OF INJUry ! parts such as switches or rechargeable batteries. Before performing any work on the appliance, The appliance is intended solely for private, not disconnect the power plug. commercial, use. j Clean t he appliance regularly, preferably If this product has been subjected to imp
Summary of the content on the page No. 12
Disposal / Conformity Declaration / Manufacturer Q tools must be collected separately and subjected to Conformity Declaration / an environmentally friendly recycling procedure. Manufacturer Your local communal or municipal authorities can We, Kompernaß GmbH, Burgstr. 21, provide information on how to dispose of the worn- D-44867 Bochum, Germany, hereby declare that out appliance. this product complies with the requirements of the following EC directives: EC machine guideline (98 / 37 / EC
Summary of the content on the page No. 13
IAN 35324 K ompernaSS GmbH Bur gstraße 21 D-44867 Boc hum © by or FGen m arketing Last Information Update: 07 / 2009 · Ident.-No.: PSS 250072009-6 6 35324_ORBITAL SANDER_Cover_LB6.indd 1 21.07.09 14:44
