Life Fitness 9100R user manual

Summary of the content on the page No. 1

AEROBIC TRAINER
INSTALLATION INSTRUCTIONS

Summary of the content on the page No. 2

Congratulations... and welcome to the world of and the Lifecycle 9100R aerobic trainer. The following Parts Identification Listing and the step by step installation procedures have been assembled to make the set-up of your aerobic trainer as quick and easy as possible. Please take special note of the following important points prior to choosing a location and beginning assembly of the Lifecycle exercise bike…

Summary of the content on the page No. 3

S A F E T Y F I R S T ! ⇒ DO NOT locate the Lifecycle 9100R aerobic trainer outdoors, near swimming pools, or in areas of high humidity. ⇒ DO NOT operate your Lifecycle 9100R aerobic trainer if it has been dropped, damaged, or even partially immersed in water. Contact Life Fitness Customer Support Services at the number on the back page of this Installation Instruction Guide. ⇒ DO NOT locate the Lifecycle 9100R aerobic trainer any closer than 30 inches ( 76 cm ) to a television set. ⇒

Summary of the content on the page No. 4

TOOLS REQUIRED FOR ASSEMBLY... Phillips screwdriver, 1/2” wrench, 5/32” hex key wrench PARTS DESCRIPTION 1 Seat Back Screw Qty. 4 2 Seat Back Washer Qty. 4 0017-00101-1131 0017-00104-0253 3 Handlebar Bolt Qty. 2 4 Console Screw Qty. 4 0017-00101-0986 0017-00101-1104 5 Seat Back Qty. 1 6 Collar Qty. 1 0K19-01078-0000 0K19-01125-0000 7 Handlebar Assembly Qty. 1 8 Display Console Qty. 1 AK19-00035-0000 AK19-00114-0001 9 9V Alkaline Battery Qty. 1 10 0017-00003-0573 11 12

Summary of the content on the page No. 5

Summary of the content on the page No. 6

Step 1 Align the four holes in the SEAT BACK (#5) with those in the SEAT BACK POSTS. Insert the four SCREWS (#1) and WASHERS (#2) through the backside of the SEAT BACK POSTS and into the SEAT BACK. Tighten the four SCREWS with a hex key wrench. NOTE: BE CAREFUL NOT TO OVER-TIGHTEN THE SCREWS. Step 2 Unfold the CONSOLE WIRE HARNESS from the POST extending from the FRAME. Step 3 Slide the COLLAR (#6) onto the HANDLEBAR ASSEMBLY (#7) with the angled side of the COLLAR facing toward the HANDLEBAR. S

Summary of the content on the page No. 7

Step 7 Carefully feed the wire back into the top of the HANDLEBAR ASSEMBLY and attach the DISPLAY CONSOLE to the HANDLEBAR ASSEMBLY using the four CONSOLE SCREWS (#4) and a phillips screwdriver. Tighten the four SCREWS in a criss-cross pattern. NOTE: BE CAREFUL NOT TO OVERTIGHTEN THE SCREWS. Step 8 To install the 9-VOLT ALKALINE BATTERY (#9) found in the parts bag use a Phillips screwdriver to remove the screw from the back door. Gently pull the BATTERY WIRES from the back of the DISPLAY CONSOLE

Summary of the content on the page No. 8

OPERATION CHECKLIST ⇒ Insure that the STABILIZER BAR and HANDLEBAR BOLTS are tight. ⇒ Make sure the aerobic trainer is properly leveled and stable. ⇒ Read the entire Operation Manual before using the trainer. English/Metric Default Setting Toggle The default setting of the Lifecycle 9100R aerobic trainer display console is set to English units of measurements at the factory. If your display console will require units of measurements to be in metric, it may be necessary to change the setting from