Summary of the content on the page No. 1
Z100 / Z300 Z500
Z700
EL555
Elliptical
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW ELLIPTICAL!
Summary of the content on the page No. 2
Table of Contents Product Registration ..2 Important Safety Instructions 3 Important Electrical Information 4 Important Operation Instructions ..4 Assembly Instructions .5 Operation of Your New Elliptical ...13 Manufacturers Limited Warranty ..25 Serial Number Sticker Location - Under console mast cover 1 EL555 Elliptical
Summary of the content on the page No. 3
CONGRATULATIONS ON YOUR NEW ELLIPTICAL AND WELCOME TO THE SPIRIT FAMILY! Thank you for your purchase of this quality elliptical trainer from Spirit Manufacturing, Inc. Your new elliptical was manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. Through your dealer, Spirit will do all we can to make your ownership experience as pleasant as possible for many years to come. The local dealership where you purchased
Summary of the content on the page No. 4
Important Safety Instructions DANGER - To reduce the risk of electric shock disconnect your elliptical from the electrical outlet prior to cleaning and/or service work. WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install the elliptical on a flat level surface with access to a nominal 110-volt, 15-amp grounded outlet with only the elliptical plugged into the circuit.. DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH ONLY ONE OUTLET ON THE EN
Summary of the content on the page No. 5
Important Operation Instructions n NEVER operate this elliptical without reading and completely understanding the results of any operational change you request from the computer. n Understand that changes in resistance do not occur immediately. Set your desired level on the computer console and release the adjustment key. The computer will obey the command gradually. n NEVER use your elliptical during an electrical storm. Surges may occur in your household power supply that could damage elliptic
Summary of the content on the page No. 6
Assembly Pack Check List Step 1 #100 - 5/16" x 20mm #96 - 3/8" x 19mm #104 - 3/8" x 23mm Flat Washer (4pcs) Curved Washer (2pcs) Flat Washer (2pcs) #128 - 3/8" #85 - M5 x10mm #89 - 3/8" Spilt Washer (1pc) Phillips Head Screw (4pcs) Nylon Nut (2pcs) #178 - 5/16" #179 - 5/16" #76 - 3/8" x 3/4" Split Washer (4pcs) Star Washer (4pcs) Hex Head Bolt (2pcs) #167 - 5/16" x 2-1/4" #77 - 3/8" x 1-1/2" Hex Head Bolt (4pcs) Hex Head Bolt (2pcs) #75 - 3/8" x 2-1/4" Hex Head Bolt (1pc) 5
Summary of the content on the page No. 7
Step 2 #102 - 25 mm #131 - 3/8" x 30mm Wave Washer (2pcs) Flat Washer (2pcs) #107 - 3.5mm x 12mm #76 - 3/8" x 3/4" Sheet Metal Screw (6pcs) Hex Head Bolt (2pcs) Step 3 #79 - 5/16" x 1-1/4" #100 - 5/16" x 20mm #91 - 5/16"mm Hex Head Bolt (2pcs) Flat Washer (2pcs) Nylon Nut (2pcs) Step 4 #157 - M6 x 10mm #107 - 3.5mm x 12mm #82 - M5 x 15mm Phillips Head Screw (4pcs) Sheet Metal Screw (2pcs) Phillips Head Screw (22pcs) 6 EL
Summary of the content on the page No. 8
Tools #126 - Phillips Screw Driver (1pc) #125 - Short Phillips Screw Driver (1pc) #124 - 13 / 14mm Wrench (1pc) #129 - 12 / 14 mm Wrench (1pc) 7 EL555 Elliptical
Summary of the content on the page No. 9
Assembly Instructions UNPACKING THE UNIT 1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift Box over the unit and unpack. 2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missing, contact your dealer immediately. 3. Locate the hardware package. The hardware is separated into steps. Remove the tools first. Remove the hardware for each step as needed to avoid confusion.
Summary of the content on the page No. 10
9 EL555 Elliptical
Summary of the content on the page No. 11
STEP 2: SWING ARM ASSEMBLY 1. Install the two 25m/m Wave Washers (102) onto the Left and Right side of the Handle Bar axle. 2. Slide the Left (10) and Right (11) Handle Bars onto the appropriate side of the axle. The handlebars have a small sticker on them indicating L (left) and R (right). 3. Install two 3/8 X 35 mm Flat Washers (131) onto the two 3/8 X 3/4 Hex Head Bolts (76) and install, and tighten, in the threaded holes in the ends of the axle. 4. Install the Front Handle Bar Covers (68
Summary of the content on the page No. 12
STEP 3: CONNECTING ARM ASSEMBLY Untie the wire holding the Sleeve Spacer (22) in place on the rod-end bearings located on the ends of the connecting arms (8&9). Align the hole in the rod ends with the hole in the brackets of the left and right Handle Bar (10&11). The rod end should be on the inside of the Handle Bar bracket. Secure both sides with a 5/16 x1-1/4 Hex Head Bolt (79), 5/16 x20mm Flat Washer (100) and 5/16 Nylon Nut (91) and tighten as much as possible. 11
Summary of the content on the page No. 13
STEP 4: PLASTICS ASSEMBLY 1. Match up the Connecting Arm Covers (71 and 72) and install onto the Left and Right Connecting Arms (8&9) and secure each side with two M5x15mm Phillips Head Screws (82) and one 3.5x12mm Sheet Metal Screws (107) by using Short Phillips Head Screw Driver (125). 2. Install Sliding Wheel Covers (64) on each side and secure with four M5x15mm Phillips Head Screws (82). 3. Install the two Stabilizer Covers (60 and 61) on the middle stabilizer bar with two M5x15mm Phillips H
Summary of the content on the page No. 14
Features Adjustable foot pedals, and correctly aligned orthopedic foot pads Through research performed with a leading sports scientist and physical rehabilitation expert; Spirit engineering has developed a breakthrough in pedal design. No other elliptical, at any price, offers these unique features. The history of elliptical use over the past few years tells us that many users suffer from numb toes while working out on elliptical trainers. Many other users complain of ankle, Achilles tendon, kne
Summary of the content on the page No. 15
Operation of Your Elliptical Getting familiar with the control panel Power up The Elliptical is supplied with an external power supply. When power is connected to the Elliptical, the console will automatically power up. If there is no input to the console for 20 minutes the console will go to stand-by mode. In stand-by mode the console display will turn off. To turn the console on press any key. When initially powered on the console will perform an internal self-test. During this time all the li
Summary of the content on the page No. 16
Console Operation Quick Start This is the quickest way to start a workout. After the console powers up you just press the Start key to begin, this will initiate the Quick Start mode. In Quick Start the Time will count up from zero and the workload and Incline may be adjusted manually by pressing the Up or Down buttons. The dot matrix display will have only the bottom row lit at first. As you increase the work load more rows will light indicating a harder workout. The elliptical will get harder t
Summary of the content on the page No. 17
Program Keys The Program Keys are used to preview each program. There are keys for the Manual program, Up and Down keys that scroll through the 5 pre-set programs, two User programs and three Heart Rate Control programs. Press each program key to preview what the program profile looks like. If you decide that you want to try a program, press the corresponding program key and then press the Enter key to select the program and enter into the data-setting mode. Heart Rate Sensors The Elliptical has
Summary of the content on the page No. 18
Manual The Manual program works as the name implies, manually. This means that you control the workload yourself and not the computer. To start the Manual program follow the instructions below or just press the Manual button then the Enter button and follow the directions in the message window. 1. Press the Manual key then press the Enter key. 2. The message window will ask you to enter your Age. You may enter your Age, using the Up and Down keys or the numeric key pad, then press the Enter key
Summary of the content on the page No. 19
Fat Burn The Fat Burn program is designed, as the name implies, to maximize the burning of fat. There are many schools of thought on the best way to burn fat but most experts agree that a lower exertion level that stays at a steady workload is the best. The absolute best way to burn fat is to keep your heart rate at around 60% to 70% of its maximum potential. This program does not use heart rate but simulates a lower, steady exertion workout. Work Profile Incline Profile Cardio The Cardio progra
Summary of the content on the page No. 20
Interval The Interval program takes you through high levels of intensity followed by periods of low intensity. This program increases your endurance by depleting your oxygen level followed by periods of recovery to replenish oxygen. Your cardio vascular system gets programmed to use oxygen more efficiently this way. Work Profile Incline Profile Programming Preset Programs: 1. Select the desired program using the program up and down keys then press the Enter key. 2. The message window will ask yo
