Summary of the content on the page No. 1
E
S
R
A
U
M
N
U
A
L
™
Éc helon
P.O. Bo x 245040
Milwaukee, WI 53224-9540
Phone: 414.354.0300
Fax: 414.354.7905
www.u-line.com
Printed in U.S.A. P/N 30001
Summary of the content on the page No. 2
U-LINE CORPORATION LIMITED WARRANTY U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase. During the initial one-ye
Summary of the content on the page No. 3
INTRODUCTION Congratulations on your purchase of the U-Line 2075DWRR drawer unit. A pioneer in the field for more than 40 years, U-Line is the world’s number one manufacturer of built-in, under-counter ice making and spe- cialty refrigeration products. U-Line dedicates 100% of its research and development to these products. The result: U-Line technology leads the market with innovation, design, depth of product line and performance. U-Line also backs customers with a strong dealer network. U-Li
Summary of the content on the page No. 4
User’s Manual If you do not return your Product Registration Card, U-Line will use the date of sale to the U-Line distributor as the first date of warranty for your unit. Please also record the purchase date of your U- Line unit and your dealer’s name, address and telephone number. Model Number: ______________________________________ Serial Number: ______________________________________ Purchase Date: ______________________________________ Dealer Name: ______________________________________ Dea
Summary of the content on the page No. 5
SAFETY PRECAUTIONS Do not attempt to install or operate your unit until you have read the safe- ty precautions in this manual. Safety items throughout this manual are labeled with a Danger, Warning or Caution based on the risk type. DEFINITIONS DANGER ! ! Danger means that failure to follow this safety statement may result in severe personal injury or death. WARNING ! Warning means that failure to follow this safety statement may result in extensive product damage, serious personal injury, or de
Summary of the content on the page No. 6
User’s Manual GENERAL PRECAUTIONS DANGER ! ! RISK OF CHILD ENTRAPMENT. Before you throw away your old refrigerator or freezer, take off the doors and leave shelves in place so that children may not easily climb inside. WARNING ! • Never attempt to repair or perform maintenance on the unit until the electricity has been disconnected. • Altering, cutting of power cord, removal of power cord, removal of power plug, or direct wiring can cause serious injury, fire and/or loss of property and/or life
Summary of the content on the page No. 7
INSTALLATION SITE PREPARATION Your U-Line drawer unit must be installed under a counter or in a wall. The unit is designed so it can be installed next to a wall, because the crisper can be accessed from either side. 1. Position the unit on a flat, level surface, capable of supporting the entire weight of the unit. Remember the unit will be significantly heavier once it is fully loaded. 2. This unit requires grounded and polarized 115 VAC, 60Hz, 15A cir- cuit (normal household current). DANGER !
Summary of the content on the page No. 8
User’s Manual Your U-Line Drawer unit is designed so it can be installed next to the wall on either side because the crisper can be accessed from either side (Figure 1, 2). CABINET OR WALL DWR001 Figure 1 – Right wall installation WARNING ! The anti-tip kit must be installed on this unit before it is used. Never use the drawers as steps or a shelf to support more than the drawers’ content. 3. The unit must be installed in a wall or under a counter top to allow for the installation of the anti-ti
Summary of the content on the page No. 9
CABINET OR WALL DWR002 Figure 2 – Left wall installation 24" MIN. DWR003 Figure 3 – Front Clearance 7
Summary of the content on the page No. 10
INTAKE EXHAUST User’s Manual 4. Position the unit to allow free air flow through the front grille (Figure 4). OFF ON DWR004 Figure 4 LEVELING THE UNIT It is important that the unit is level. All Échelon™ Series units are equipped with adjustable feet for leveling and height adjustment (Figure 5). To level the unit: 1. Adjust all four leveling feet evenly so that the top of the cabinet is at the desired installation height. 2. Using a level of at least two feet in length, measure the level of th
Summary of the content on the page No. 11
4. Place the unit in position where it is to be installed. Re-check cabi- net height and levelness (Figure 6) and adjust if necessary. RAISE LOWER DWR005 Figure 5 LEVEL TWO PLACES DWR021 Figure 6 9
Summary of the content on the page No. 12
User’s Manual BUILT-IN INSTALLATION Your U-Line product is designed for built-in installation only. When built-in, it does not require additional air space for the top, sides, or rear. However, the front grille must NOT be obstructed. NOTE To ease unit installation and removal, it is recommended that the cabinet rough opening dimensions be increased by at least 1/4" over the dimensions given for your unit. Unit Dimensions Width Height Depth* 23-15/16" 34-1/8" 24" * For full overlay door panels,
Summary of the content on the page No. 13
COUNTER TOP OR WALL ANTI-TIP KIT DWR010 Figure 7 CUSTOM DRAWER PANELS Two types of custom drawer panels can be installed on your U-Line unit to harmonize with or accent the surrounding decor. FULL OVERLAY DRAWER PANEL Full overlay drawer panels completely cover the drawer frames and han- dle to give a built-in appearance. See Table 1 for full overlay drawer panel dimensions (Figure 11, see page 13). Table 1. Full Overlay Panel Dimensions 1 2 1 A B C Top panel with 1/2" gap 11-13/16" 14-3/4" 1"
Summary of the content on the page No. 14
User’s Manual OVERLAY PANEL KIT PARTS Part Number Description Quantity 42120 Spacer Nylon 3/8 OD x .19 ID 10 42121 Screw #10 x 5/8 Round Head 10 • The total weight of both drawer panels must not weigh more than 20 lbs. • The thickness of the drawer panel must be 3/4". Remove existing drawer front from cabinet: GASKET HANDLE 1. Open drawer. Pull door gasket (Figure 8) out of the groove (top edge of door only). Start in the mid- dle and pull outward, moving SCREW toward the edge. This may take som
Summary of the content on the page No. 15
5. On a clean surface, place the wood panel face down and tape the existing drawer panel (removed in step 3) on the back of the wood panel (Figure 10) and drill the five (5) holes (5/32" drill 3/8" deep) through the coated steel panel and 3/8" into the wood panel according to the diagram (Figure 11). Remove tape from the draw- er panel, and enlarge the five holes in the front panel using a .0201" drill (#7) drill. SIDE OF BACK OF WOOD PANEL COATED STEEL WOOD PANEL DRAWER PANEL TAPE NOTE: For
Summary of the content on the page No. 16
User’s Manual 6. Attach the drawer panel to the wood panel using #10 x 5/8" (P/N 42121) wood screws and nylon spacers (P/N 42120). The nylon spacers fit between the wood panel and the drawer panel as shown (Figure 12). COATED STEEL DRAWER PANEL TYPICAL WOOD PANEL #10 X 5/8" ROUND HEAD SCREW FIVE REQUIRED PLASTIC SPACER FIVE REQUIRED DWR_OL_005 Figure 12 Drawer panel and wood panel must be aligned properly or drawer will not operate correctly. Assembling the drawer and wood panel: 7. Install the
Summary of the content on the page No. 17
CUSTOM INSERT DRAWER PANEL Custom drawer panels can be inserted into the drawer frames to match the surrounding decor. Custom drawer panels B can be flat or raised, as long as the maximum panel thickness where inserted into the drawer reveal (channel) is 1/4" A thick. For raised panels, the depth of the reveal is 1/4" on all four sides. See Table 2 for custom drawer panel insert dimensions (Figure 13). A Table 2. Custom Insert Drawer Panel Dimensions DWR007 AB Figure 13 12-15/16" 23-1/32" The
Summary of the content on the page No. 18
User’s Manual Install the custom insert as follows: WARNING ! Insert edges may be SHARP! Use care when installing. 1. Open drawer. Pull drawer gas- FULL HANDLE SHOWN ket out of groove (top edge of drawer only). Start in the mid- dle and pull outward, moving toward the edge (Figure 14). This may take some force, be careful. 2. Remove the three screws behind the gasket. Carefully pull the top handle up and off. You may discard the top handle as it will be replaced with the full handle. DWR020 3. R
Summary of the content on the page No. 19
5. Slide custom drawer panel insert into 1/4" channel in drawer front. 6. Attach the full handle to the lower handle using the 3 screws removed in step 2. 7. Holding drawer gasket out of the way, replace handle on drawer making sure it is seated properly on insert and that screw holes line up. 8. Install two screws removed in step 3. 9. Starting at the corners and working inward, push drawer gasket into place on the drawer. INITIAL START-UP AND ADJUSTING THE TEMPERATURE CONTROL Once the installa
Summary of the content on the page No. 20
User’s Manual TEMPERATURE CONTROLLER 1 2 WARMER WARMER SET COOLER COOLER TEMP TEMP CLRCO011B Figure 17 The temperature controller (Figure 17) is located in the top drawer. It consists of an LED display, two LED status indicator lights and three touch pad buttons. The LED display shows the temperature set point and is calibrated in degrees Fahrenheit. The controller is factory programmed for a set point of 38°F which will show when the unit is first powered-up. To display actual temperature, pre
