Summary of the content on the page No. 1
RECORD THIS INFORMATION FOR FUTURE REFERENCE RECORD THIS INFORMATION FOR FUTURE REFERENCE RECORD THIS INFORMATION FOR FUTURE REFERENCE
RECORD THIS INFORMATION FOR FUTURE REFERENCE RECORD THIS INFORMATION FOR FUTURE REFERENCE
BEFORE BEFORE BEFORE BEFORE BEFORE INSTALLING THE UNIT: INSTALLING THE UNIT: INSTALLING THE UNIT: INSTALLING THE UNIT: INSTALLING THE UNIT:
Model No. _______________ Serial No. ______________________
Product No. ________________________
Date Purchased ___________ Place of P
Summary of the content on the page No. 2
SECTION A. SECTION A. SECTION A. SECTION A. SECTION A. INST INST INST INST INSTALLA ALLA ALLA ALLA ALLATION TION TION TION TION The lower side vent is fitted with a panel which provides an 1. GENERAL INSTRUCTIONS adequate access opening for ready serviceability of the This appliance is designed for storage of food and burner and control manifold of the refrigerator. This should storage of frozen food and making ice. be centered on the back of the refrigerator. The refrigerators outlined herein h
Summary of the content on the page No. 3
6. CLEARANCES FIG. 1A Minimum clearances in inches to combustible materials are: G G G G G: Top 0" K K K K K: Side 0" L L L L L: Bottom 0" M M M M M: Rear 1" N N N N N: See NOTE P: P: P: P: P: See NOTE NOTE NOTE NOTE NOTE NOTE: Clearance "M M M M M" is between the rearmost part of the refrigerator and the wall behind the refrigerator. NOTE NOTE NOTE NOTE NOTE: Clearance "N N N N N" is the distance between the bottom of the lower vent to the top of upper side vent. For ventilation height, refer t
Summary of the content on the page No. 4
7. INSTALLING REFRIGERATOR IN ENCLOSURE NOTE: DO NOT install the appliance directly on carpet- The dimensions shown in FIG. 3 will give ing. Carpeting must be removed or protected by a you adequate space for service and proper metal or wood panel beneath the appliance, which installation. extends at least the full width and depth of the appli- ance. FIG. 3 FIG. 3 FIG. 3 FIG. 3 FIG. 3 e Refrigerator Refrigerator Refrigerator Refrigerator Refrigerator Overall Overall Overall Overall Overall Instal
Summary of the content on the page No. 5
C. SECURING REFRIGERATOR 8. GAS CONNECTION Hook-up to the gas supply line is accomplished at the IN ENCLOSURE manual gas shutoff valve, which is furnished with a 3/8" The refrigerator is installed in the enclosure with eight SAE (UNF 5/8" – 18) male flare connection. Always use a screws. Six screws are in the front frame and two are in the backup wrench when connecting the gas supply line to the plate on the rear. See FIG. 5. gas inlet fitting. All completed connections should be checked for lea
Summary of the content on the page No. 6
9. 9. TESTING LP GAS SAFETY SHUT TESTING LP GAS SAFETY SHUTOFF OFF 9. 9. 9. TESTING LP GAS SAFETY SHUT TESTING LP GAS SAFETY SHUT TESTING LP GAS SAFETY SHUTOFF OFF OFF IMPORTANT: The gas safety shutoff must be tested after the refrigerator To prevent the refrigerator from being left on and is connected to LP gas supply. draining the battery when the vehicle's engine is not running and charging the battery, it is recom- To test the gas safety shutoff, proceed as follows: To test the gas safety sh
Summary of the content on the page No. 7
F. Replace door on lower hinge pin. Replace upper hinge A. Remove the door. See Section 12. pin and bushings removed in Step A. B. Remove the lower trim molding. (NOTE: Trim G. Check that the door closes properly and seals all molding is not installed on new units in cartons) around. C. Fit the new panel in place and slide it up as far as possible. D. Fit the trim molding back in place. 13. INSTALLATION OF DECORATIVE DOOR PANEL The door panel can easily be mounted. The dimensions of the panel mu
Summary of the content on the page No. 8
2. CONTROLS The gas and electric controls are located at the rear of the refrigerator and are accessible through the lower vent in the outside wall of the vehicle. See FIG. 8. A = DC ON/OFF SWITCH B = GAS ON/OFF SAFETY VALVE C = PIEZO IGNITOR D = ELECTRIC THERMOSTAT E = AC ON/OFF SWITCH F = GAS INLET FITTING G = DC TERMINAL BLOCK FIG. 8 3.OPERATING INSTRUCTIONS A. LP GAS OPERATION After initial installation, servicing, or changing gas cylin- 7) If the burner has not lit, repeat the lighting proc
Summary of the content on the page No. 9
The refrigerator is designed for the storage of fresh foods, milk, etc. It is not intended for the storage of frozen food. Most LP gas appliances used in recreational vehicles The internal volume of the refrigerator is 1.7 cubic feet, net. are vented to the outside of the vehicle. When parked NEVER PUT HOT FOOD INTO THE REFRIGERATOR. close to a gasoline pump, it is possible that the gasoline fumes could enter this type of appliance and Avoid using large dishes and do not stack food or food ignit
Summary of the content on the page No. 10
E. CLEANING Cleaning the refrigerator is usually done after it is defrosted or put into storage. To clean the interior of the refrigerator, use lukewarm water and a mild dishwashing detergent. Use only warm water to clean the finned evaporator, gaskets, ice trays and shelves. NEVER use strong chemi- cals or abrasives to clean these parts as the protective surfaces will be damaged. It is important to always keep Most LP gas appliances used in recreational vehicles the refrigerator clean. are vent
Summary of the content on the page No. 11
7) Reassemble the components in the reverse order to C. Examination and Cleaning of Flue, Burner and Jet that described above. Once or twice a year, look through the opening (see FIG. 9) in the burner box and examine the appearance of the FIG. 11 burner flame which should be predominantly blue in color when the gas thermostat knob is set to its highest position. (Refer to FIG. 10). If this is not the case, and if you have checked the chapter "Generals", the flue, burner, jet, etc. should be clea
Summary of the content on the page No. 12
7) Reassemble the components in the reverse order to E. If the refrigerator fails to work DC, check: that described for removal, taking care to remake the 1) That the DC supply is connected to the refrigerator. gas connections soundly, and not forgetting to refit the 2) That the fuse on the DC supply is intact. flue baffle. 3) That the DC switch is set to the "ON" position (A, in 8) Reinstall the refrigerator in its recess. Connect the gas FIG. 8). and electrical supplies, and check for gas leak
