Summary of the content on the page No. 1
FWV450 and FWV900
Wine Coolers
Manual for Installation, Use and Maintenance
Passionate about style
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
Summary of the content on the page No. 2
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment. This appliance is not designed to be used by people (including children) with reduced physical, sensorial or mental capacity, or who lack experience or knowledge about it,
Summary of the content on the page No. 3
Before first use You must allow the appliance to settle for at least twenty four hours prior to switching the power on. It is recommended that you remove all internal and external packaging and clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm water and then thoroughly dry the interior. The appliance may have an odour to it at first use. This will disappear as the appliance cools. Please note: • The appliance will work continuously until
Summary of the content on the page No. 4
Use and Controls FWV450 Key: 1 – Power button 2 – Light button 3 – Up button 4 – Down button FWC450 control panel 1 2 3 4 c F C/ F To switch the power on/off Press and hold the power button for five seconds. To change the temperature • Press the up or down buttons until the required temperature is shown on the display. • The preset temperature is 12˚C / 54˚ F. • To change the temperature display from Fahrenheit to Celsius, or Celsius to Fahrenheit, press and hold the up and down but
Summary of the content on the page No. 5
Use and Controls FWV900 Key: 1 – Light button 2 – Temperature set button 3 – Up button 4 – Down button FWC450 control panel 1 2 3 4 c F C/ F To switch the power on/off Press and hold the light and temperature set buttons simultaneously for five seconds. To change the temperature • Press the temperature set button once to select the upper zone. • The LED display for the upper zone will flash. • Press the up or down buttons until the required temperature is shown on the display. •
Summary of the content on the page No. 6
Care and Cleaning Always disconnect the appliance from the mains electrical supply before any cleaning or maintenance. • Do not use abrasive products or detergents. After washing, rinse and dry thoroughly. • The exterior of the appliance and the door seal should be cleaned using mild soapy water and dried thoroughly. • The interior cabinet should be cleaned using a solution of bicarbonate of soda and lukewarm water. • Clean the shelves separately by hand using soap and water. Do not put them
Summary of the content on the page No. 7
Troubleshooting If you have any problems with your appliance, you should check the troubleshooting guide prior to calling CDA Customer Care to prevent unnecessary service calls and potential cost. If the appliance is not working, check • There is power to the appliance • The house fuses or circuit breakers are intact and the fuse in the plug has not blown. • The plug socket is functioning correctly. To check this, plug another electrical appliance in to see if the socket is working. • The a
Summary of the content on the page No. 8
Installing the wine cooler This appliance is intended to be built in to a kitchen cabinet. This appliance should be installed in a well ventilated, dry room. This appliance must not be installed: 1. In direct sunlight 2. Adjacent to a heat source (oven or radiator) 3. Below a hob unit Place your wine cooler in a location which is strong enough to support its weight when fully loaded. To level the wine cooler, adjust the front levelling legs at the bottom of the wine cooler. Ensure that there i
Summary of the content on the page No. 9
Reversing the door It is possible to reverse the door on this appliance, if required. To do so, follow the steps below: 1. With the door closed, remove the upper hinge pin cover, and then the upper and lower hinge pins. Support the door to prevent it falling. 2. Remove the door carefully and place it on a padded surface to avoid the risk of damage. 3. Unscrew the four upper hinge plate screws on the right hand side and the blanking screws on the upper left hand side. Remove the right upper h
Summary of the content on the page No. 10
Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit a replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position. How to connect an alternative plug If the fitted plug is not suitable
Summary of the content on the page No. 11
Summary of the content on the page No. 12
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
