Summary of the content on the page No. 1
FWC151 / FWC301 / FWC601 /
FWC621 Wine Coolers
Manual for Installation, Use and Maintenance
Passionate about style
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
Summary of the content on the page No. 2
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment. This appliance is not designed to be used by people (including children) with reduced physical, sensorial or mental capacity, or who lack experience or knowledge about it,
Summary of the content on the page No. 3
Before first use You must allow the appliance to settle for at least twenty four hours prior to switching the power on. It is recommended that you remove all internal and external packaging and clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm water and then thoroughly dry the interior. The appliance may have an odour to it at first use. This will disappear as the appliance cools. Please note: • The appliance will work continuously until
Summary of the content on the page No. 4
Use and Controls FWC151 4 1 2 3 Key: 1 – Power button 2 – Light button 3 – Up button 4 – Down button fig. 1 FWC301 3 4 1 2 Key: 1 – Power button 2 – Light button 3 – Up button 4 – Down button fig. 2 To switch the power on/off Press and hold the power button for five seconds. To change the temperature • Press the up or down buttons until the required temperature is shown on the display. • The preset temperature is 12˚C / 54˚ F. • To change the temperature display from Fahrenheit to Celsius,
Summary of the content on the page No. 5
Use and Controls FWC601 1 2 3 4 Key: 1 – Light button 2 – Temperature set button 3 – Up button 4 – Down button fig. 3 To switch the power on/off Press and hold the light and temperature set buttons simultaneously for five seconds. To change the temperature • Press the temperature set button once to select the upper zone. • The LED display for the upper zone will flash. • Press the up or down buttons until the required temperature is shown on the display. • Press the temperature set
Summary of the content on the page No. 6
Use and Controls FWC621 Left zone Right zone 1 2 3 4 5 6 7 8 9 10 c c F F C/ F Temp. Temp. Key: Key: 1 – Power on/off 6 – °F/°C selection button 2 – Light button 7 – Light button 3 – Temperature display 8 – Temperature display 4 – Up button 9 – Up button 5 – Down button 10 – Down button fig. 4 To switch the power on/off Press and hold the power button for five seconds. To change the temperature • Press the up or down buttons for the zone until the required temperature is sho
Summary of the content on the page No. 7
Use Humidity Control (all models except FWC151) The wine coolers are equipped with a humidity control system to maintain optimal humidity within the wine cooler. Fill the humidity reservoir approximately 3/4 full with water. Place the reservoir on the runners on the top shelf as shown in fig. 5. Ensure it is located correctly to prevent water spillage. fig. 5 Check the water level regularly and refill if required. Temperature display The temperature display will show the current inte
Summary of the content on the page No. 8
Care and Cleaning Always disconnect the appliance from the mains electrical supply before any cleaning or maintenance. • Do not use abrasive products or detergents. After washing, rinse and dry thoroughly. • The exterior of the appliance and the door seal should be cleaned using mild soapy water and dried thoroughly. • The interior cabinet should be cleaned using a solution of bicarbonate of soda and lukewarm water. • Clean the shelves separately by hand using soap and water. Do not put them
Summary of the content on the page No. 9
Troubleshooting If you have any problems with your appliance, you should check the troubleshooting guide prior to calling CDA Customer Care to prevent unnecessary service calls and potential cost. If the appliance is not working, check • There is power to the appliance • The house fuses or circuit breakers are intact and the fuse in the plug has not blown. • The plug socket is functioning correctly. To check this, plug another electrical appliance in to see if the socket is working. • T
Summary of the content on the page No. 10
Installing the wine cooler This appliance is intended to be installed in a space between two units. The minimum space required is: FWC151 – 150 mm wide x 555 mm deep x 825 mm high FWC301 – 300 mm wide x 580 mm deep x 825 mm high FWC601 – 600 mm wide x 580 mm deep x 825 mm high FWC621 – 600 mm wide x 580 mm deep x 825 mm high Please note: When the product is installed, there should be a small ventilation gap between the top of the unit and the underside of the worktop (6 mm or ¼”) These produc
Summary of the content on the page No. 11
Installation This appliance is designed to fit under worktops between 820 – 890mm in height, using one of two plinth plates to ensure that the feet are concealed from view. Installation under a kitchen worktop between 820-850 mm in height Install the wine cooler as described on page 9. Extend the adjustable feet to bring the wine cooler up to the required height. Then extend the plinth section up to a maximum of 101mm, and tighten the two screws on the front of the plinth section. Installati
Summary of the content on the page No. 12
Reversing the door It is possible to reverse the door on this appliance, if required. To do so, follow the steps below: 1. Open the door and remove the screws (1) securing the bottom hinge to the appliance(6). Support the door to prevent it from falling. 2. Gently pull down the door (5) to remove it from the fig. 7 top hinge and place on a padded surface to avoid the risk of damage. 3. Separate the hinge pin (3) from the lower hinge (2) and refit on the alternative lower hinge wi
Summary of the content on the page No. 13
Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position. How to connect an alternative plug If the fitted plug is not suitable f
Summary of the content on the page No. 14
13
Summary of the content on the page No. 15
14
Summary of the content on the page No. 16
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
