Summary of the content on the page No. 1
Operation/Programming/Maintenance
Drying Tumblers
Stacked 30 Pound Capacity
Stacked 45 Pound Capacity
Starting Serial No. 0602004144
Refer to Page 3 for Model Numbers
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 70400101R2
July 2007
www.comlaundry.com
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Installation must conform with local codes or in the absence of local codes with: In the U.S.A., installation must conform to the latest edition of the American National Standard Z223.1/ NFPA 54 “National Fuel Gas Code” and Standard ANSI/NFPA 70 “National Electric Code.” In Canada, installation must comply with Standards CSA-B149.1 or Natural Gas and Propane Code CSA C22.1, latest edition, Canadian Electric Code, Part I. In Australia, installation must comply with the Australian Gas Association
Summary of the content on the page No. 4
Introduction......................................................................................... 3 Table of Model Identification ............................................................................. 3 Customer Service.................................................................................. 4 Contents Serial Plate Location............................................................................. 4 Wiring Diagram............................................................
Summary of the content on the page No. 5
Introduction Model Identification Information in this manual is applicable to these models: Gas Steam Electric CHD30STG2-CAT30L CHD30STS2-CTT30S CHD30STE2-CTT30E CHD30STG2-CAT30N CHD30STS2-CUT30S CHD30STE2-CUT30E CHD30STG2-CTT30L DRST30S2-BTT30S DRST30E2-BTT30E CHD30STG2-CTT30N DRST30S2-BUT30S DRST30E2-BUT30E CHD30STG2-CUT30L IPD30STS2-ITT30S IPD30STE2-ITT30E CHD30STG2-CUT30N DRST30G2-BAT30L T30 DRST30G2-BAT30N DRST30G2-BTT30L DRST30G2-BTT30N DRST30G2-BUT30L DRST30G2-BUT30N IPD30STG2-ITT30L IPD3
Summary of the content on the page No. 6
Introduction Customer Service Wiring Diagram If literature or replacement parts are required, contact The wiring diagram is located in the upper junction or the source from which the machine was purchased or upper contactor box. The wiring diagram part number contact Alliance Laundry Systems at (920) 748-3950 is located in the lower portion of the electrical data on for the name and address of the nearest authorized the serial plate. parts distributor. For technical assistance, call (920) 748
Summary of the content on the page No. 7
Safety Information IMPORTANT: Warranty is void unless tumbler is Explanation of Safety Messages installed according to instructions in the Precautionary statements (“DANGER,” “WARNING,” Installation Manual. Compliance with minimum and “CAUTION”), followed by specific instructions, specifications and requirements detailed herein, are found in this manual and on machine decals. These and with applicable local gas fitting regulations, precautions are intended for the personal safety of the
Summary of the content on the page No. 8
Safety Information 14. The interior of the tumbler and the exhaust duct Important Safety Instructions should be cleaned periodically by qualified Save These Instructions service personnel. 15. If not installed, operated and maintained in WARNING accordance with the manufacturer’s instructions or if there is damage to or mishandling of this product’s components, use of this product could Hazardous Voltage. Can cause shock, burn expose you to substances in the fuel or from fuel or cause de
Summary of the content on the page No. 9
Safety Information 23. Remove laundry immediately after tumbler 29. DO NOT bypass any safety devices. stops. 30. Solvent vapors from dry-cleaning machines 24. Always read and follow manufacturer’s create acids when drawn through the heater of the instructions on packages of laundry and cleaning drying unit. These acids are corrosive to the aids. Heed all warnings or precautions. To reduce tumbler as well as to the laundry load being the risk of poisoning or chemical burns, keep dried. Be sur
Summary of the content on the page No. 10
Operating Instructions WARNING To reduce the risk of fire: � DO NOT DRY articles containing foam rubber or similarly textured rubberlike materials. � DO NOT DRY plastics, anything containing wax or chemicals such as mops and cleaning cloths, or anything dry-cleaned at home with a dry-cleaning solvent. � DO NOT TUMBLE fiberglass curtains and draperies unless the label says it can be done. If they are dried, wipe out the cylinder with a damp cloth to remove particles of fiberglass. W076 To redu
Summary of the content on the page No. 11
Operating Instructions Control Instructions TMB2119N Figure 3 Dual Digital Timer Control IMPORTANT: To stop the tumbler at any time during the cycle, OPEN DOOR. If the loading door QT Control Suffix or lint panel door is opened during the cycle, the heating system will shut off and the motor will stop. 1. Select HIGH, MED, LOW or NO HEAT by To restart the cycle, both doors must be closed and turning the temperature knob. the START button must be pressed in. 2. Set the HEAT TIME for the nu
Summary of the content on the page No. 12
Operating Instructions Error Codes WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: � Disconnect electric power to the tumbler before servicing. � Close gas shut-off valve to gas tumbler before servicing. � Close steam valve to steam tumbler before servicing. � Never start the tumbler with any guards/panels removed. � Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the tumbler is properly grounded.
Summary of the content on the page No. 13
Operating Instructions C 25 Figure 4 Single Drop Control Preliminary Control Information Power-Up Mode SD and SX Control Suffixes When power is applied to the tumbler the control will 1. Select HIGH, MED, LOW or NO HEAT by enter Ready Mode, unless a cycle was in process prior turning the temperature knob. to a disruption of power. If a power disruption is less 2. Insert the coin(s) in the coin slot. than 5 seconds, with a cycle in process, the control will enter Run Mode once power is rest
Summary of the content on the page No. 14
Operating Instructions Run Mode If the control receives a coin drop pulse during cool down the IN USE LED will flash briefly to indicate the In Run Mode, the control is running a cycle. The IN coin input, the machine will exit cool down and it will USE LED is lit. start heating. The cycle time will be equal to the Door Open Mode programmed dry time In Door Open Mode, the control turns off the heater Temperature Selector Switch and motor when the door is opened during a run For five minutes
Summary of the content on the page No. 15
Operating Instructions Run Mode Ignition Control Operation While in Run Mode the ignition control leaves the gas Power Up valve on, monitors the flame signal, and leaves the After 24 VAC is applied to the ignition control pins igniter off. 24V and GND, the Diagnostic LED on the ignition If a flame signal is lost during Run Mode, one control will turn orange/yellow. If a fault is detected additional retrial for ignition will take place within one the ignition control will enter Lockout M
Summary of the content on the page No. 16
Operating Instructions System Tests Flame Probe Tests The following system tests are performed during Unexpected Presence of Flame normal operation. System tests are performed at a The Unexpected Presence of Flame test is performed minimum of every 24 hours. when no flame is expected. Failure of this test results Low Voltage Detection in the ignition control entering Lockout Mode with the Diagnostic LED displaying Error Code 3. If the voltage between terminals TH and GND on the control is
Summary of the content on the page No. 17
Maintenance WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: � Disconnect electric power to the tumbler before servicing. � Close gas shut-off valve to gas tumbler before servicing. � Close steam valve to steam tumbler before servicing. � Never start the tumbler with any guards/panels removed. � Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the tumbler is properly grounded. W002 c. Be sure the lin
Summary of the content on the page No. 18
Maintenance WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: � Disconnect electric power to the tumbler before servicing. � Close gas shut-off valve to gas tumbler before servicing. � Close steam valve to steam tumbler before servicing. � Never start the tumbler with any guards/panels removed. � Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the tumbler is properly grounded. W002 4 TMB2116N 3 1 2 T
Summary of the content on the page No. 19
Maintenance WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: � Disconnect electric power to the tumbler before servicing. � Close gas shut-off valve to gas tumbler before servicing. � Close steam valve to steam tumbler before servicing. � Never start the tumbler with any guards/panels removed. � Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the tumbler is properly grounded. W002 Monthly Bi-Annuall
Summary of the content on the page No. 20
Maintenance WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: � Disconnect electric power to the tumbler before servicing. � Close gas shut-off valve to gas tumbler before servicing. � Close steam valve to steam tumbler before servicing. � Never start the tumbler with any guards/panels removed. � Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the tumbler is properly grounded. W002 Daily Maintenance
