Summary of the content on the page No. 1
Electric Dryer
Models 8907*
Code No. : DC68-02865A-02 Sears Canada Inc., Toronto, Ontario, Canada M5B 2C3 www.sears.ca
Summary of the content on the page No. 2
TABLE OF CONTENTS PROTECTION AGREEMENTS Master Protection Agreements TABLE OF CONTENTS ............................... 2 Congratulations on making a smart purchase. Your new PROTECTION AGREEMENTS .......................... 2 Kenmore product is designed and manufactured for years of KENMORE APPLIANCE WARRANTY ................... 3 dependable operation. But like all products, it may require preventive maintenance or repair from time to time. That's when DRYER SAFETY ...............................
Summary of the content on the page No. 3
KENMORE APPLIANCE WARRANTY ONE YEAR LiMiTED WARRANTY DiSCLAiMER OF iMPLiED WARRANTIES; LiMiTATiON OF REMEDIES When installed, operated and maintained according to all instructions supplied with the product, if this appliance fails due Customer's sole and exclusive remedy under this limited to a defect in material or workmanship within one year from the warranty shall be product repair as provided herein. Implied date of purchase, call 1-800-4-MY-HOME _ to arrange for free warranties, including w
Summary of the content on the page No. 4
I I DRYER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manuN and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "WARNING" or "CAUTION." ® These words mean: You can be killed or seriously injured if you don_t immediately
Summary of the content on the page No. 5
I I iNSTALLATiON iNSTRUCTiONS Mobile home installations require metal exhaust system hardware available for purchase from your local Sears store or Sears Service Center. For further information, please call 1=800= 4=MY=HOME e (1 =800=469=4663). Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Pedestal --..>_ You have the option of purchasing a pedestal for this dryer. You may select a 14"(35.5cm) pedestal. Rem
Summary of the content on the page No. 6
I I Dryer Dimensions -. i Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Place dryer at least 18 inches {46 cm) above the floor for a garage installation. Failure to do so can result in death, explosion, or fire. Youwillneed [] A location that allows for proper exhaust installation. See A: 39"(99. Ocm) "Venting Requirements." B : 27"(68.6crn) [] A separate 30-amp circuit. C : 49"(124.5crn) D : 29.4"(74.7crn) [] If you are using a power supply cord, a gro
Summary of the content on the page No. 7
I I Closet installation - Dryer only Recommended instalia_on spacing for recessed or closet instaJJation, with stacked washer and dryer The dimensions shown are for the recommended spacing. (2.5cm) 174.7cm) d2.7cm) A B _-t _ , o> A. Side view - closet or confined area 24 in._ * J_ B. Closet door with vents ._-- 1"' (2.5cn_) (155 cm_) * Required spacing * Required spacing ** For side or bottom venting, 2" (5.1 cm) spacing is allowed. Recessed or cJoset instaJJation = Dryer on pedestaJ = 14" m_.'
Summary of the content on the page No. 8
I I GROUNDING INSTRUCTIONS [] For a grounded, cord-connected dryer: This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer is equipped with a cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly Electrical Shock Hazard installed and grounded in accordance with all local codes a
Summary of the content on the page No. 9
I I =iiidiiiii::::!_,ii_'ii iii:iiiil_iii!!!!!iii:iI !i:;:iii@(_:iiiii;iiiiil,' @1ii ?,;@iiiii iiil]!ii; Flexible metal vent [] Flexible metal vents are acceptable only if accessible for cleaning. [] Flexible metal vent must be fully extended and supported when the dryer is in its final location. [] Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance. Do not install flexible metal vent in enclosed walls, ceilings Fire Hazard [] f
Summary of the content on the page No. 10
I I [] Exhaust hood must be at least 12" (30.5 cm) from the ground Optional exhaust installations or any object that may be in the path of the exhaust (such as This dryer can be converted to exhaust out the right side, left flowers, rocks or bushes, snow line, etc.). side, or through the bottom, Contact your local dealer to have the dryer converted, [] Do not use an exhaust hood with a magnetic latch. improper venting can cause moisture and lint to collect indoors, which may result in: [] Moistu
Summary of the content on the page No. 11
I I Vent system chart NOTE: Side and bottom exhaust installations have a 90 ° turn inside the dryer. To determine maximum exhaust length, add one 90 ° turn to the chart. METHOD1 The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. Weather Hood Type Recommended , Use oNy for short-run 1. if space permits, attach the brass female end of the "Y" installation connector to the cold water faucet. 2. Turn the cold water faucet off. 3. Attach the straight
Summary of the content on the page No. 12
I I Method2 The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. To set the dryer to the same height as the washer, fully retract 1. if "Y" connector cannot be attached directly to the cold the leveling feet by turning them counterclockwise, then loosen water faucet, the short hose must be used. the legs by turning them clockwise 2. Turn the cold water faucet off. Adjust the leveling feet only as much as necessary to level the dryer. Extending the
Summary of the content on the page No. 13
I I i_:::;::ii_!!;_,_i::!!!:_'S_:!i!!_ Cili_O_,O_ ¸'¸_¸ S;wiii_i_ii_iii,!!!!iiiiilI 8. Reattach the holder lever. 1. Unplug the power cord. 2. Remove two door hinge screws. ,9. Lift the door and remove it. 9. Reattach the screws in the remaing holes. 4. Remove a screw on the Frame Front 10. Reinsert the screw in the other hole. 5, Remove the two screws on the opposite side of the door \ hinge. ////' 11. Reinsert the screw (Step 4) on the Frame Front 6. Remove two screws from the holder lever. 12
Summary of the content on the page No. 14
I I 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. ,3. Dispose of/recycle all packaging materials. 4. Be sure the water faucets are on. 5. Check for leaks around "Y"-connector, faucet and hoses. 6. Check the dryer's final location. Be sure the vent is not crushed or kinked. 7. Check that the dryer is level. See "Level Dryer." 8. For power supply cord installation, plug into a
Summary of the content on the page No. 15
I I DRYER USE Models :8907* S_
Summary of the content on the page No. 16
I I Refresh Models : 8907* This cycle is best for smoothing out wrinkles and reducing odors from loads consisting of one to four dry items. In this cycle a small amount of water is sprayed into the dryer drum after several minutes of tumbling with heat. f S_dlage _ capteur Programme inimut_ Normal Touch Up TimedDry Normal S_chage _ MinLLterie _Air Fluff HeavyDuty Grande Rendement Flu× d'a# This cycle will release wrinkles from items that have been left PermPress in the dryer too long. In this cy
Summary of the content on the page No. 17
I I WrinMe Guard Temp Selection Button To select the correct temperature for the load, press the Temp Wrinkle Guard provides approximately 90 minutes of intermittent button. An indicator light will illuminate next to the desired tumbling in unheated air at the end of the cycle to reduce temperature. Press the button repeatedly to scroll through the wrinkling. Press the Wrinkle Guard button to activate this feature. settings. The indicator light above the pad will illuminate when Wrinkle Guard is
Summary of the content on the page No. 18
I I ChildLock A function to prevent children from playing with your dryer. Installing the drying rack 1. Open the Dryer door. Setting/Releasing 2. Position drying rack in tumbler, placing the front lip of the if you want to set or release the Child Lock, press both the Time drying rack on the top of the lint filter. and Cycle Signal buttons simultaneously for 3 seconds. 3. Place the rear legs in the two recessed areas of the dryer's back wall then push down the middle of the drying rack to How t
Summary of the content on the page No. 19
I I DRYER CARE Tumbler Remove any stains such as crayon, ink, or fabric dye (from new Cleanthe lintfilter items such as towels or jeans) with an all purpose cleaner. Tumble old towels or rags to remove any excess stain or [] After each load. cleaning substance. [] To shorten drying time. Once these steps are followed, stains may still be visible, but [] To operate more energy efficiently. should not transfer to subsequent loads. NOTE: Do not operate your Dryer without the lint filter in place. S
Summary of the content on the page No. 20
I I SPECIAL LAUNDRY TiPS From inside the Dryer Cabinet Please follow the care label or manufacturer's instructions for drying special items. Lint should be removed every 2 years, or more often, depending if care label instructions are not available, use the following on dryer usage. Cleaning should be done by a qualified person. information as a guide. Fromthe ExhaustVent Lint should be removed every 2 years, or more often, depending Bedspreads & Comforters on dryer usage. [] Follow the care lab
