Summary of the content on the page No. 1
MODEL 463248708 • PRODUCT GUIDE
THIS GRILL IS FOR OUTDOOR USE ONLY.
CAUTION: WARNING:
Read and follow all safety statements, assembly Failure to follow all manufacturer’s instructions could
instructions, and use and care directions before result in serious personal injury and/or property
attempting to assemble and cook. damage.
INSTALLER/ASSEMBLER: CAUTION:
Leave this manual with consumer. Some parts may contain sharp edges – especially as
noted in the manual! Wear protective gloves if
neces
Summary of the content on the page No. 2
WARNING DANGER CALIFORNIA PROPOSITION 65 If you smell gas: 1. Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects, and other 1. Shut off gas to the appliance. reproductive harm. 2. Extinguish any open flame. 2. This product contains chemicals, including lead and 3. Open lid. lead compounds, known to the State of California to cause cancer, birth defects or other reproductive harm. 4. If odor continues, ke
Summary of the content on the page No. 3
TABLE OF CONTENTS For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Grill Service Center. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 To insure your satisfaction Product Record Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 and for follow-up service, Installation Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 2 register your grill Safety Symbols. . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
LP Cylinder Valve • A disconnected LP cylinder in USE AND CARE storage or being transported must have a safety cap installed (as shown). Do not store an LP cylinder in enclosed spaces such as a carport, garage, porch, covered DANGER Safety patio or other building. Never leave an LP cylinder Cap inside a vehicle which may become overheated • NEVER store a spare LP cylinder under or near Retainer Strap by the sun. the appliance or in an enclosed area. • Do not store an LP cylinder in an area whe
Summary of the content on the page No. 5
e s i w k LP Cylinder Exchange Connecting Regulator to the LP Cylinder • Many retailers that sell grills offer you the option of replacing 1. LP cylinder must be properly secured onto grill. (Refer to your empty LP cylinder through an exchange service. Use only assembly section.) those reputable exchange companies that inspect, precision fill, 2. Turn all control knobs to the OFF position. test and certify their cylinders. Exchange your cylinder only for an OPD safety feature-equipped cylind
Summary of the content on the page No. 6
Straight Leak Testing Valves, Hose and Regulator 1. Turn all grill control knobs to OFF. 2. Be sure regulator is tightly connected to LP cylinder. 3. Completely open LP cylinder valve by turning hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately. There is a major leak at the connection. Correct before proceeding. 4. Brush soapy solution onto areas circled below. Hold coupling nut and regulator as shown for proper connection to LP cylinder valve. 6. Turn the cou
Summary of the content on the page No. 7
Safety Tips s Before opening LP cylinder valve, check the coupling nut for WARNING tightness. s When grill is not in use, turn off all control knobs and LP For Safe Use of Your Grill and to Avoid Serious cylinder valve. s Never move grill while in operation or still hot. Injury: s Use long-handled barbecue utensils and oven mitts to avoid • Do not let children operate or play near grill. burns and splatters. • Keep grill area clear and free from materials that burn. s Maximum load for side
Summary of the content on the page No. 8
Burner Flame Check • Remove cooking grates and flame tamers. Light burners, rotate WARNING knobs from HIGH to LOW . You should see a smaller flame in LOW position than seen on HIGH. Perform burner Turn controls and gas source or tank OFF when not flame check on sideburner, also. Always check flame prior to in use. each use. If only low flame is seen refer to "Sudden drop or low flame" in the Troubleshooting Section. HIGH CAUTION LOW If ignition does NOT occur in 5 seconds, turn th
Summary of the content on the page No. 9
Cleaning the Burner Assembly CAUTION Follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting grill. 1. Turn gas off at control knobs and LP cylinder. 2. Remove cooking grates and flame tamers. SPIDER ALERT! 3. Remove screws and carryover tubes from rear of burners. 4. Remove screw and washers to disengage burner from bracket on firebox. SPIDER AND WEBS INSIDE BURNER TUBE 5. Remove screws to detach electrode from burner. Electrode should remai
Summary of the content on the page No. 10
Food Safety Food safety is a very important part of enjoying the outdoor cooking experience. To keep food safe from harmful bacteria, follow these four basic steps: Clean: Wash hands, utensils, and surfaces with hot soapy water before and after handling raw meat and poultry. Separate: Separate raw meats and poultry from ready-to-eat foods to avoid cross contamination. Use a clean platter and utensils when removing cooked foods. Cook: Cook meat and poultry thoroughly to kill bacteria. Use a
Summary of the content on the page No. 11
CARE AND CLEANING OF YOUR STAINLESS STEEL GRILL Routine cleaning is necessary to preserve the appearance and corrosion resistance of Stainless Steel. The perception that many people have is that stainless steel will not rust. That is not the case in certain conditions. Rust marks are regular steel particles that have become attached to the surface of stainless steel. They may also occur if you are using a steel wool or wire wool scouring pad instead of a nylon scouring pad to clean your grill
Summary of the content on the page No. 12
Key Qty Description Part # PARTS LIST – Model No. 463248708 PP 2 Door Handle . . . . . . . . . . . . . . . . . . . . . . . . 80065506 QQ 1 Right Door Assembly . . . . . . . . . . . . . . . . . 80016936 Key Qty Description Part # RR 5 Flame Tamers. . . . . . . . . . . . . . . . . . . . . . . 80017023 A 1 Bottom Shelf. . . . . . . . . . . . . . . . . . . . . 80016961 SS 4 Quantum Infrared Cooking Grates . . . . . . . 80016962 B 2 Locking Caster . . . . . . . . . . . . . . . . . . . 80000268 TT 1 T
Summary of the content on the page No. 13
PARTS DIAGRAM – Model No. 463248708 LL MM CCC II EE HH FF Kk2 BBB DDD Kk3 Kk1 EEE ZZ JJ NN WW UU X BB GG R XX AA DD V U AAA Y CC III Z K J N YY M HHH VV S E L D W G H RR SS I JJJ P FFF T KK GGG Y QQ O TT F Q C C B B OO PP A 463248708 • 13
Summary of the content on the page No. 14
Front Rear ASSEMBLY – Model No. 463248708 Attach the two locking casters at the rear of the bottom shelf 1 and the two fixed casters at the front. Use the provided caster wrench to fully tighten casters. Fixed caster Locking caster Bottom shelf Attach side panels to bottom shelf using three 1/4-20x1/2” screws, 1/4-20x1/2” screw 7mm lock washers, and 7mm flat washers per panel shown A. 2 IMPORTANT: Panel with large hole must 7mm lock washer Be on left side of bottom shelf. Unscrew Hex Nut and
Summary of the content on the page No. 15
Place lower back panel between side panels at rear of bottom shelf. Make sure the slots are positioned as shown (A). Secure 3 lower back panel to side panels using two 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers on each side. 7mm lock washer 7mm flat washer 1/4-20x1/2” screw Upside Lower back panel Left A Right A Downside Insert wire ends into lower back panel (A). Attach front right side of wire shelf to the right side panel with one 4 #8-32x3/8” screw, 4mm flat washer and 4mm
Summary of the content on the page No. 16
Insert front brace under control panel and between cart side panels with door magnets towards the top. Secure using four 6 1/4-20x1½” screws, 7mm lock washers, and 7mm flat washers, two on each side. NOTE: MAKE SURE THAT THE FRONT BRACE IS MOUNTED IN THE MOST DOWNWARD POSITION WHEN ASSEMBLED TO CART. 7mm flat washer 7mm lock washer 1/4-20x1½” screw Front brace On back of grill, place upper back panel between side panels and 7 above lower back panel. Secure upper back panel, in lower holes, u
Summary of the content on the page No. 17
Insert tabs on right side shelf into rectangular slots in side of side panel. Attach rear of shelf using one 1/4-20x3/4” screw, 8 7mm lock washer, and 7mm flat washer in upper hole. Use one 1/4-20x1½” screw, 7mm lock washer, and 7mm flat washer in lower hole. Attach front of shelf and fascia using three 1/4-20x3/4” screws, 7mm lock washers, and 7mm flat washers. Attach towel bar to right side shelf with two 1/4-20x1/2” screws, 7mm lock washers and 7mm flat washers(A). Place the wire basket u
Summary of the content on the page No. 18
Insert tabs on left sideburner shelf assembly into rectangular slots in side of side pane show (A). Attach rear of shelf using 9 one 1/4-20x3/4” screw, 7mm lock washer, and 7mm flat washer in upper hole. Use one 1/4-20x1½” screw, 7mm lock washer, and 7mm flat washer in lower hole. Attach front of shelf and fascia using three 1/4-20x3/4” screws, 7mm lock washers, and 7mm flat washers. Now you may fully tighten lower screws on upper back panel. Remove the screw shown (B), then add one large fl
Summary of the content on the page No. 19
First, remove the two screws and lock washers factory attached to the sideburner valve bracket. Position sideburner 10 valve bracket beneath sideburner shelf fascia so that valve stem comes through larger center hole in fascia. Align the holes on valve bracket with left and right holes on fascia. Secure using lock washers and screws that were removed from bracket. Next, place sideburner bezel over valve stem on front side of fascia. Align small holes on bezel with upper and lower holes on f
Summary of the content on the page No. 20
Place sideburner lid onto left shelf and align holes in back of lid with hinge holes. Secure lid to hinges using four #10-24x3/8” 12 screws, 5mm flat washers, 5mm lock washers, and #10-24 hex nuts. NOTE: Fully secure one hinge with screws, washers and nuts, then secure remaining hinge. Sideburner lid #10-24 hex nut 5mm lock washer #10-24x3/8” screw 5mm flat washer Place burner cap onto sideburner. Attach sideburner 13 cap clip (B) and sideburner cooking grate into holes in drip pan. Next,
