Clam Corp CLAM 6800 8202 user manual

Summary of the content on the page No. 1

M o d e l N o .

- 8 2 0 2 -

S p e c i f i c a t i o n s
H e i g h t - 7 6 i n c h e s ( 1 0 ” p a c k e d )
▪
▪ D e p t h - 7 2 i n c h e s
W i d t h - 9 6 i n c h e s ( 4 4 ” p a c k e d )
▪
Weight – 1 0 0 l b s .
▪
p / n 1 0 8 3 3 1

Instruct ion No. 102487












- Clam Customer Service Information -

NOTICE!! - ONCE USED, THIS SHELTER CANNOT BE RETURNED TO THE STORE. IF YOU HAVE A
WARRANTY CLAIM, HAVE YOUR SALES RECEIPT READY AND

Summary of the content on the page No. 2

SAFETY INSTRUCTIONS Please fully understand and follow all safety instructions outlined in this booklet. Failure to do so could result in severe injury. Death from asphyxiation may result from use of oxygen depleting heaters. Open all vents for • Do not use open flame heaters in your ice shelter. fresh air ventilation. Open vents for cross ventilation. Injury or death may result from fire if tent fabric is exposed to open flame. • Ice Armor fabric will melt when contact

Summary of the content on the page No. 3

(Parts on this page are NOT actual size.) PARTS IDENTIFICATION #5 HOOP POLE PART 101236 #3 SQUARE POLE PART 101655 #7 SPREADER TUBE PART 101244 #8 DOME POLE PART 101247 #25 A SUPPORT BRACE #26 B SUPPORT BRACE PART 101197 PART 101192 Page 3

Summary of the content on the page No. 4

(Parts below this box ARE shown actual size.) PARTS IDENTIFICATION #21 1" WASHER #15 NYLOCK NUT #28 KEPS NUT PART 101206 PART 101163 PART 101191 #24 3/4" SCREW #44 3/4" SCREW #27 CARRIAGE BOLT PART 101212 PART 101088 PART 101209 #12 1-3/4" BOLT PART 101211 Page 4

Summary of the content on the page No. 5

CLAM 6800 EXPLODED VIEW Page 5

Summary of the content on the page No. 6

ASSEMBLY INSTRUCTIONS BEFORE ATTEMPTING TO USE THIS PRODUCT ON THE ICE practice setting up and taking down at home in the comfort of a heated area. Repeat several times until comfortable. This will make your on-ice set-up much easier. NO TOOLS ARE NEEDED FOR ASSEMBLY OF YOUR CLAM 6800. 1. INITIAL SET-UP a. Open the Clam 6800 and lay on a flat level surface. b. Lift up the two hoop pole sections until the snap button locks into place. Lock the braces. See Diag

Summary of the content on the page No. 7

ASSEMBLY INSTRUCTIONS 5. DISMANTLING YOUR CLAM a. To take your Clam 6800 down, repeat steps 1–3 in reverse order. Lay all the poles on one side of the base. Fold the tent into the base, making sure you don’ t fold or crease the windows as that could cause them to crack. b. Close up the base and secure the rubber latches. Note: Continuous pulling behind a four wheeler or snowmobile will result in premature wear of the base. We recommend a ski or slide system be mounted to the base

Summary of the content on the page No. 8

ASSEMBLY DIAGRAMS DIAGRAM B DIAGRAM C Spreader Tubes Page 8

Summary of the content on the page No. 9

ASSEMBLY DIAGRAMS DIAGRAM D Dome Pole DIAGRAM E Page 9

Summary of the content on the page No. 10

ASSEMBLY DIAGRAMS DIAGRAM F Page 10

Summary of the content on the page No. 11

- Safety Instructions - Please fully understand and follow all safety instructions as outlined. Failure to do so could result in severe injury or death. Do not use open flame heaters in your ice shelter. Injury or death may result from fire if tent fabric is ▪ exposed to open flame. The tent is not fireproof, but the fabric is treated with a fire retardant that meets CPAI-84 specifications. Application of any foreign substance may render the flame retardant properties ineffective. Ic

Summary of the content on the page No. 12