Fisher-Price BOUNCE 'N PLAY ACTIVITY DOME 79534 user manual

Summary of the content on the page No. 1

BOUNCE ’N PLAY
ACTIVITY DOME
Model Number: 79534, 79545, 79546
Please save these instructions for future reference.
Tool needed for assembly: Phillips Screwdriver (not included).
Use only for a child who is unable to push up on hands and knees, pull up or sit unassisted.
Product features may vary from picture above.

Summary of the content on the page No. 2

WARNINGS WARNING Failure to follow these warnings and the assembly instructions could result in serious injury or death. • Never leave child unattended. ® • To prevent suffocation from entrapment, use only the Fisher-Price pad provided. Never use additional padding or mattress. • To prevent falls, use only for a child who is unable to push up on hands and knees, pull up or sit unassisted. • To prevent strangulation: _ Never place items with a string, such as hood strings or pacifier cords, aroun

Summary of the content on the page No. 3

® ® PARTS Metal Canopy Stay Pad 2 Covers 3 Toys (Toys may be different than shown) 2 Base Wires Base Spring - 4 Plastic Mesh Cover Stay 13 M5 x 1 /16" Screw - 2 CAUTION 5 In its unassembled state, this 8 M6 x 1 / " Screw - 8 product contains small parts. Adult assembly is required. M5 Lock Nut - 2 M6 Lock Nut - 8 SHOWN ACTUAL SIZE 3

Summary of the content on the page No. 4

ASSEMBLY IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. Button Hole Plastic Mesh Frame Cover Stay 3 1 Middle Hole Middle Hole Mesh Cover Frame Tube Frame Tube • Position the ends of the frame tubes against the middle holes Base in a frame. • Open the base and position it upr

Summary of the content on the page No. 5

ASSEMBLY Metal Canopy Stay 5 7 Cover Upper Hole • Tighten the screws with a Phillips screwdriver. Do not over-tighten. Slot Tab • Repeat this procedure to attach the other ends of the frame tubes to the frame on the other side of the base. Protruding Side Frame 13 M5 x 1 /16" Screw -2 M5 Lock Nut -2 6 Lower Hole • Position one end of the metal canopy stay against the upper hole in a frame. 13 • Insert an M5 x 1 /16" screw through the hole in the cover. Spring • Fit the end of the screw through

Summary of the content on the page No. 6

® ASSEMBLY USE To Unfold Toys Canopy 8 Fasteners 1 Pad Fastener Sides of Base Wire • Position the product upright on a flat surface. • Grasp both sides of a base wire. • Pull both sides of the base wire outward and then let the base wire rotate down. Note: If the base wire does not freely rotate down, pull the sides • Fasten the pad fasteners to the base fasteners. of the base wire further outward. • Lift the canopy. • Attach the toys to the canopy fasteners. IMPORTANT! Assembly is now complete,

Summary of the content on the page No. 7

® ® USE Using the Mesh Cover Zipper 3 Mesh Cover Up 5 Canopy Up Frame Groove Base Wire • Push down on the product to be • Adjust the canopy and mesh cover up. sure each side of the base wire is • While holding the mesh cover up, fasten the zipper closed. in the correct position. The base Correct wire should rest in the groove in each frame. To Fold for Portability • Repeat Use steps 1 - 3 to unfold the other base wire. Using the Canopy 6 Canopy Up Frame 4 Canopy Down Groove Groove Sides of Base

Summary of the content on the page No. 8

USE CARE The pad and toys are machine washable. Wash the pad and toys separately in cold water on the gentle cycle. Do not use bleach. Base Wire Tumble dry separately on low heat and remove promptly. The fabric and frame may be wiped clean using a mild cleaning 7 solution and a damp cloth. • Rotate the base wire up. • Repeat this procedure to fold the other base wire. If you have any questions about this product: In CANADA: Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.