Summary of the content on the page No. 1
D
™
Grow With Me Grow With Me
Grow With Me
RC Rally RC Rally
RC Rally
Model Number 77306
Please keep this instruction sheet for future reference,
as it contains important information.
Requires four "C" (LR14) alkaline batteries for control tower; four "AA"
(LR6) alkaline batteries for car; and one 9V (6LR61) alkaline battery
for remote controller (batteries not included).
Adult assembly is required.
Tool required for assembly:
Phillips screwdriver (not included).
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
Summary of the content on the page No. 2
Parts Double Flag 2 Flags Handle Ring of Fire Remote Controller Control Holder Tower Ramp Handle Support 4 Stadium Crash Gate Lights Car Remote Controller 2 Ramp Rails Starting Ramp Dirt Track 3 Cones 5 Barrels 3 Hay Flexible Bales Track 5 8 #6 x / " Screw - 7 Label sheet not shown. Shown Actual Size 2
Summary of the content on the page No. 3
Battery Installation Control Tower Car Battery Compartment Door Battery Compartment Door 1.5V x 4 1.5V x 4 “AA” (LR6) “C” (LR14) Shown Actual Size Shown Actual Size • Locate the battery compartment on the bottom of the car. • Locate the battery compartment on the back of the control tower. • Loosen the screw in the battery compartment door with a Phillips • Loosen the screws in the battery screwdriver. Remove the battery compartment door with a Phillips compartment door. screwdriver. Remove the
Summary of the content on the page No. 4
Battery Installation Remote Controller • Locate the battery compartment on the back of the remote controller. • Loosen the screw in the battery compartment door with a Phillips screwdriver. Remove the battery compartment door. • Insert one 9V (6LR61) alkaline Battery battery, as indicated inside the Compartment Door battery compartment. • Replace the battery compart- ment door and tighten the screw with a Phillips screwdriver. Do not over-tighten. 9V 9V (6LR61) Shown Actual Size 4
Summary of the content on the page No. 5
When To Replace Batteries If this toy is working slowly or erratically, it’s likely that batteries need to be replaced. While it is possible that all batteries may need replace- ment, the batteries that will need replacement most often are the batteries in the car, followed by the remote controller, and then the control tower. For more information, see the troubleshooting guide beginning on page 19. Battery Tips • We recommend using alkaline batteries for longer battery life. • Do not mix old a
Summary of the content on the page No. 6
Assembly WARNING This product contains small parts in its unassembled state. Adult assembly is required. 1 2 Handle Pegs Double Flag Handle Support Handle Support • Fit the handle onto the handle support as shown. • Position the handle support so 3 the pegs are facing you. • With the checkered side facing down, fit the double flag on to the pegs on the handle support. • Insert three screws through the holes in the handle and into the handle support. Tighten the screws with a Phillips screwdriv
Summary of the content on the page No. 7
Assembly 4 5 Handle Assembly Control Tower Handle Starting Ramp Pegs Tab Starting Remote Ramp Controller Holder • Insert the handle and starting • "Snap" the remote controller ramp into the matching holes in holder onto the tab on the bottom the control tower as shown. of the starting ramp, as shown. • Lift the control tower storage • Insert and "snap" the pegs on compartment door. Insert two the bottom of the handle screws through the control tower assembly into the matching holes and into the
Summary of the content on the page No. 8
Assembly 6 7 Ring of Fire Ramp Ramp Tabs Peg Peg Hole Ramp Ramp Hole Ramp Rail Rail Assembly • Insert and "snap" the tabs on • Gently squeeze the ring of fire the ramp into the matching to insert the pegs on either slots in a ramp rail. end into the matching holes at the top of the ramp assembly, • Repeat this procedure to as shown. attach the other ramp rail. 8
Summary of the content on the page No. 9
Label Decoration Proper label application will help keep labels looking their best! When applying labels, keep the following guidelines in mind: • Wash hands before applying labels. • Before applying labels, wipe the surface of the toy with a clean, dry cloth to remove dust or oils. • For best results, avoid repositioning a label once it has been applied. • Apply labels as shown in the illustration. One-time assembly is now complete. 4 2 3 4 3 8 11 10 9 7 12 1 5 12 6 9
Summary of the content on the page No. 10
Mode I - Beginner Driver Mode I is for a beginner or younger driver. Automatic Course Control always keeps the car hugging the track, even over obstacles. Just press the remote controller button to go and release to stop. Setting Up The Track Control Tower End of Track Plug Plug Hint: For best performance, use this toy on a smooth, flat surface. We do not recommend use on a deep, pile carpet. This toy is designed for indoor use only. • Unfold the flexible track into an oval shape and place it be
Summary of the content on the page No. 11
Mode I - Beginner Driver Ring of Fire Ramp Crash Gate Flag Stadium Light Dirt Track • Note the grooves on the edges of the crash gate, the ring of fire ramp and the dirt track. • Fit the grooves on these three obstacles onto the flexible track. Place the obstacles anywhere you like, but be sure to keep them on the outside of the track, as shown. Hint: For best performance, space the obstacles equally around the course. • Fit the four stadium lights anywhere onto the track. • Fit the two flags
Summary of the content on the page No. 12
Mode I - Beginner Driver Let’s Go Mode Switch Reset Switch On/Off On/Off Button Button ON/OFF Button Speed Control Switch • Slide the mode switch on top • Locate the reset switch on the of the car to I for beginner back of the control tower. driver mode. • Slide the reset switch ON . • Locate the speed control switch • Locate the ON/OFF button on on the bottom of the car. the front of the control tower. • Slide the switch to either slow • Press the ON/OFF button to speed or fast speed . turn
Summary of the content on the page No. 13
Mode I - Beginner Driver Battery Installation Battery Installation Battery Installation Battery Installation WARNING Arrows To prevent entanglement, keep hair away from wheels. • Note the arrows on the starting ramp. Forward • Press the forward button on the remote controller. The car moves around the track, hugging all the way without steering! Hint: The car only travels forward • Place rear wheels of the car on in Mode I - Beginner Driver. The the starting ramp, making sure reverse butt
Summary of the content on the page No. 14
Mode II - Pro Driver Mode II is for a more experienced driver who has acquired better manual skills. In this mode, your child can take full control of steering and direction. For some challenging fun, your child can set up an off road course and use the remote controller wheel to steer around obstacles. Setting Up The Track Mode Switch ON/OFF Button • For off-road fun, place the starting Speed Control Switch ramp, dirt track, ring of fire or • Slide the switch on the top of crash gate in any l
Summary of the content on the page No. 15
Mode II - Pro Driver Wheel Reset Switch Forward Reverse • Press the forward button ON/OFF on the remote controller.The Button car moves forward. • Press the reverse button on the remote controller. The car • Turn the control tower power moves backward. on to hear sound effects each • Use the wheel on the remote time the car drives over the controller to maneuver around starting ramp. the track or past obstacles. • Be sure the reset switch on the Note: The range of the remote control tower i
Summary of the content on the page No. 16
Storage 3 1 Storage Door • Fold up the track, as shown. • Lift the control tower storage compartment door. 4 • Place the barrels, cones, hay bales and road flags into the control tower storage compart- ment and door. Close the door. 2 Track Track • Slide the track over the starting ramp. • Remove the flexible track from both sides of the control tower. 16
Summary of the content on the page No. 17
Storage 5 7 Dirt Track Crash Ring of Gate Fire Ramp • Fit the dirt track to the crash • Fold the ring of fire down onto gate as shown. the ramp. • Fit the ring of fire ramp onto 6 the dirt track as shown. Control Tower 8 Hook Dirt Track • Slide the edges of the dirt track into the grooves in the handle support and control tower. • Attach the car to the hook on the handle support as shown. 17
Summary of the content on the page No. 18
Storage Care • Keep the car tires clean for best performance. 9 • Wipe this toy with a clean cloth dampened with a mild soap and water solution. Do not immerse this toy. • This toy has no consumer serviceable parts. Do not take this toy apart. • Do not drop this toy on a hard surface. • Fit the stadium lights onto the track as shown. 10 • Place the remote controller in the holder as shown. 18
Summary of the content on the page No. 19
Troubleshooting Guide Symptom Solution Car moves very slowly • Battery power in the car may be weak. Replace all four batteries with fresh, alkaline batteries. • The wheels may be dirty. Wipe them with a clean cloth dampened with a mild soap and water solution. In Mode I, the car runs • Battery power in the control tower may be weak. closer and closer to Replace all four batteries in the control tower with the track; or car keeps fresh, alkaline batteries. hitting track • The car may be going a
Summary of the content on the page No. 20
Troubleshooting Guide Symptom Solution • The car mode switch may be set to off O. Be sure the Car does not respond to the remote controller mode switch on the car is set to l or ll . • The power indicator on the car is off, and the car may have turned off automatically. Press the ON/OFF button on the car to turn it on again. The button should light up. • If the ON/OFF button on the car is lit, battery power in the remote controller may be weak. Replace the battery in the remote controller with a
