Summary of the content on the page No. 10
OPERATION IGNITION TRIGGER (OPTIONAL) This optional feature allows the unit to activate the panic mode if an unauthorized operator turns on the Ignition after the vehicle had been locked using the remote. This is similar to an alarm feature. To avoid an Ignition trigger, use the remote for BOTH LOCKING and UNLOCKING the vehicle. If system does trigger, press button #4 to reset. EMERGENCY OVERRIDE/VALET MODE (WITH OPTIONAL STARTER DISABLE FEATURE) If you have lost the transmitter or
Summary of the content on the page No. 11
GREEN (-) LOCK OUTPUT CS-845 RKE RED +12V FOR RELAYS FUSE (-) UNLOCK OUTPUT BLUE BOX IGN. SW BLUE: OVERRIDE RED: LED ACTIVATES ON 2nd PRESS OF UNLOCK BUTTON OVERRIDE/ PROGRAM SWITCH TO FACTORY HORN RELAY LED YELLOW +IGN SWITCHED "ON" VIOLET (-) PASSENGER UNLOCK OUTPUT 86 85 PARKING 87 LIGHTS BLUE WHITE 87A 30 (-) HORN OUTPUT + 10A MAX RELAYS NOT INCLUDED GREEN FUSE RED (-)AUX OUTPUT #2 15 A +12 VOLT POWER INPUT + - 86 85 87 BATTERY GRAY 87A 30 (-) AUX OUTPUT (TRUNK POP) BROWN OPTIONAL IGNIT
Summary of the content on the page No. 12
Summary of the content on the page No. 1
REMOTE KEYLESS ENTRY SYSTEMS
INSTALLATION & OPERATING INSTRUCTIONS
CS-845RKE / CS-855RKE
INTRODUCTION
CONGRATULATIONS on your choice of a Remote Keyless Entry System by Crimestopper Security Products
Inc. This booklet contains the information necessary for installing, and using your system. If any questions
arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number
below.
*IMPORTANT INFORMATION: Primary and Optional
Summary of the content on the page No. 2
INSTALLATION CAUTIONS & WARNINGS BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, AND BATTERY). DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering column, or any other moving parts in the vehicle. REMOVE MAIN SYSTEM FUSE(S) before jump starting the vehicle or charging the battery at high boost. DAMAGE MAY OCCUR TO SYSTEM IF PROPER PRECAUTIONS ARE NOT OBSERVED. COMPONENT
Summary of the content on the page No. 3
WIRING GRAY WIRE: (-) AUXILIARY REMOTE OUTPUT 1 (Optional, requires relay) Connect to terminal 85 of relay. Connect terminal 86 to constant. Connect terminal 87 to +12V or Ground depending on the type of circuit that needs to activated. Connect terminal 30 to the device/circuit to be activated. Controlled by pressing and holding Button (3) Trunk Pop for more than 1 second. GREEN WIRE: (-) AUXILIARY REMOTE OUTPUT 2 (Optional, requires relay) This wire connects the same way as Remote
Summary of the content on the page No. 4
CS-845 RKE POWER DOOR LOCK WIRING 3 PIN (WHITE): DOOR LOCK OUTPUT PLUG GREEN: (-) Negative LOCK pulse RED: +12V Coil Power for external relays (Term. 86). BLUE: (-) Negative UNLOCK pulse CS-845RKE NEGATIVE TRIGGER DOORLOCK WIRING CS-845RKE POSITIVE TRIGGER DOORLOCK WIRING GREEN GREEN FUSED RED RED +12V BLUE + BLUE 86 85 86 85 87 87 30 87A 30 87A FACTORY FACTORY L L POWER POWER LOCKING LOCKING UL UL RELAYS RELAYS CS-845RKE REV. POLARITY DOOR LOCK WIRING CS-845RKE AFTERMARKET DOOR LOCK
Summary of the content on the page No. 5
CS-855 RKE POWER DOOR LOCK WIRING 3 PIN (WHITE): DOOR LOCK OUTPUT PLUG GREEN: (-) Negative LOCK pulse / (+) Positive UNLOCK pulse RED: +12V Coil Power for external relays (Term. 86). BLUE: (-) Negative UNLOCK pulse / (+) Positive LOCK pulse CS-855 RKE NEGATIVE TRIGGER DOORLOCK WIRING CS-855 RKE POSITIVE TRIGGER DOORLOCK WIRING GREEN GREEN RED RED BLUE BLUE IN4001 IN4001 DIODES * DIODES * L FACTORY L FACTORY LOCK LOCK POWER POWER LOCKING LOCKING UL UL RELAYS RELAYS UNLOCK UNLOCK CS-85
Summary of the content on the page No. 6
CS-845/855 SEPARATE DRIVER’S DOOR UNLOCK DIAGRAMS REVERSE POLARITY DOOR LOCKS VIOLET GREEN FUSED +12V RED + BLUE 85 86 85 86 DRIVER'S 85 86 87 87 DOOR MOTOR 87 87A 30 87A 30 30 87A + + L L CUT UL UL CUT UNLOCK WIRE CUT NEGATIVE TRIGGER DOOR LOCKS VIOLET GREEN RED BLUE DRIVER'S 85 86 L L DOOR MOTOR 87 UL UL 30 87A FACTORY LOCK RELAYS +12V + FUSED CUT UNLOCK WIRE
Summary of the content on the page No. 7
TRANSMITTER PROGRAMMING rd 1. Turn Ignition ON and OFF 3 times quickly, leaving it ON the 3 time. (ON/OFF, ON/OFF, ON) Lights should flash once and one horn chirp. 2. Push the Program/Override Button for 5 seconds until you hear 3 horn chirps and lights flash 3 times. Release the Button. 3. Press the #1 (LOCK) on new transmitter – lights will flash for code learn confirmation. Repeat step 3 for up to 2 additional transmitters. The system will learn a total of 3 transmitter codes. 4.
Summary of the content on the page No. 8
OPTION PROGRAMMING To change programmable options: 1. Turn the Ignition ON, wait one second, and press the Override/Program button 5 times. 2. The system should flash the parking lights 8 times in quick succession. 3. Within the next few seconds, press the Override/Program button [again] the number of times that corresponds to the options chart below. Parking lights and/or optional LED should flash for each button press. Don’t lose count! 4. When you get to the desired option number, p
Summary of the content on the page No. 9
OPTION PROGRAMMING cont. 6. IGNITION TRIGGER This option controls the unit’s optional Ignition trigger feature. If selected to ON, then the vehicle’s horn will honk if an unauthorized operator turns on the Ignition after the vehicle had been locked with the remote. This function is similar to an alarm system. To avoid a trigger, use the remote for BOTH LOCKING and UNLOCKING the vehicle. If system accidentally triggers, press button #4 to reset. OPTION RESET PROCEDURE: Programmable
