Summary of the content on the page No. 1
ASTRA 777
WITH SEPERATE
LOCK/UNLOCK BUTTONS
VEHICLE SECURITY SYSTEM
PRODUCT MANUAL
Summary of the content on the page No. 2
Limited Lifetime Warranty This vehicle security system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid. After the first 12 month warranty period there will be a maximum serv
Summary of the content on the page No. 3
Table of Contents 1. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 2. 2-way LCD Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 2-way LCD Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Adding/Replacing 2-way LCD Transmitters . . . . . . . . .
Summary of the content on the page No. 4
Summary of the content on the page No. 5
About Your System Congratulations on your purchase of this state-of-the-art vehicle security system from ScyTek Electronics. With proper installation this system will provide superior protection and performance for many years to come. System Contents: • Main Unit • One 5-Button 2-Way LCD Remote Transmitter • One 5-Button Random Code Remote Transmitter • 2-Way Pager Transceiver Antenna • High Output 6-tone Siren • Dual Stage Shock Sensor • Status LED • Coded Emergency Override/ Valet Switch
Summary of the content on the page No. 6
2-way LCD Remote Transmitter Description Button 1 Button 2 Button 3 Button 4 Button 5 The Astra’s 777 2-way LCD remote transmitter is offering increased range and confirmation of any activated feature. Page 1 Button 1 Arms and Locks* the system and when held for 5 seconds, activates the system’s Panic feature. Button 1 also locks the doors when the system is in Valet Mode. Button 2 Disarms and Unlocks* the system. Pressing Button 2 again operates the Passenger Unlock feature (if installed). B
Summary of the content on the page No. 7
Adding/Replacing 2-way LCD Transmitters (2 LCD remotes maximum) When adding an optional 2-way LCD transmitter to the system, follow these steps: 1. Turn on the ignition key On, Off, On, Off, On, Off, and back On. (Key On 4 times) · The siren will chirp 4 times. 2. Press and hold the Override switch for 5 seconds. · The siren will chirp 4 times. · The LED will illuminate. 3. Press Button 1 on the first transmitter, then on the second transmitter. · The siren will chirp once for each transmit
Summary of the content on the page No. 8
LCD Backlight Transmitter Button 5 is used for confirmation, transmitter programming, as well as activation of the LCD backlighting for use in the dark. Press button 5 to activate the LCD backlight. System Confirmation The 2-way transmitter's confirmation feature allows the current vehicle status to be displayed at any time. To display system status: 1. Press and hold Button 5 until the display shows CON. · The transmitter will beep once. 2. Release Button 5. · The transmitter will beep once. ·
Summary of the content on the page No. 9
VLT Valet mode function sets and resets the security system valet mode. * this function is enabled only when the security system is disarmed Set or reset the Valet mode: 1. Press and hold Button 6 until the display shows VLT. · The transmitter will beep six times. 2. Release Button 5. · The LCD panel will play a tone if the Valet mode was set “V" will be displayed indicating that the system is in Valet mode. · The transmitter will beep twice if the Valet mode was reset. “V" will turn off indicat
Summary of the content on the page No. 10
Remote Transmitters Remote Transmitter Description LED Button 1 Button 2 Button 5 Button 3 Button 4 The Astra 777 is supplied with one 5-button Remote Transmitter used to control system operations. Button 1 Arms and Locks* the system and when held for 5 seconds, activates the system’s Panic feature. Button 1 also locks the doors when the system is in Valet Mode. Button 2 Disarms and Unlocks* the system. Pressing Button 2 again operates the Passenger Unlock feature (if installed). Button 2 al
Summary of the content on the page No. 11
Adding/Replacing One-Way Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below. Note: Up to 4 one-way transmitters can be programmed to operate the system. Any previously stored transmitter code will be erased if it is not programed within the following sequence. To program the transmitter(s): 1. Turn on the ignition key On, Off, On, Off, and back On. · The siren will chirp 3 tim
Summary of the content on the page No. 12
System Operation Remote Arming The system monitors 4 independent areas (zones) while armed: doors, hood/trunk, shock sensor and optional sensor input. To Arm the System: 1. Turn off the ignition. 2. Press Button 1. · The siren will chirp once.* · The doors will lock. · The parking lights will flash once. · The LED will turn on, to indicate the starter defeat is activated. 3. 5 seconds after Arming: · The LED will start blinking to indicate that the doors and hood/trunk inputs are being moni
Summary of the content on the page No. 13
Tamper Alert If the system was triggered while away, the LED will flash to indicate which zone triggered the system after disarming and turning on the ignition. The LED indication will repeat 8 times. LED Flashes: 1 flash = optional sensor 2 flashes = shock sensor 3 flashes = not used 4 flashes = door 5 flashes = trunk 10 flashes = main power interrupt or system was reset example: flash-flash-pause-flash-flash-pause = shock sensor Silent Arming/Disarming The system can be programmed to op
Summary of the content on the page No. 14
Panic Mode In the event of an emergency, the transmitter’s remote Panic feature can be used to instantly trigger the alarm. To activate the Panic Mode: 1. Press and hold Button 1 for 5 seconds. · The alarm will sound. · The parking lights will flash. · The doors will unlock* allowing access to the vehicle. 2. Press Button 2 to stop Panic Mode. * If the ignition is on when the Panic feature is activated, the doors will lock for personal safety. Emergency Override If the transmitter becomes lost
Summary of the content on the page No. 15
6. Turn off the ignition then arm the system. 7. Disarm the system using the new Override Code to permanently store the new code. Note: If the code set procedure is not properly performed, turn off the ignition and begin again. The override code will not be permanently stored until the code is used to disarm the system. Automatic Rearming The Automatic Rearming feature is designed to protect the vehicle in the event the system is accidentally disarmed. With the Automatic Rearming feature enabl
Summary of the content on the page No. 16
Extended Features Ignition Controlled Door Locks For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on, and unlock the doors after the ignition key is turned off. If a door is open when the ignition is turned on, the ignition locking feature is disabled to protect against locking the keys inside the vehicle. Dome Light Activation If the optional Dome Light Activation feature is i
Summary of the content on the page No. 17
System Installation 1. Thoroughly read and become familiar with the installation instructions before beginning the installation. 2. Review system contents: Main Unit 1 One-Way 5-Button Remote Transmitter 1 Two-Way 5 Button LCD Transmitter Siren Shock Sensor Harnesses Reciever Antenna • 14-Pin main harness • 4-Pin shock sensor harness • 3-Pin door lock harness • LED harness • Valet Switch harness • Receiver Harness 3. Verify with the owner, the mounting locations for all visible components, inc
Summary of the content on the page No. 18
Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment. Choose a mounting location that will not be easily accessible to a thief, and will not interfere with the operation of any vehicle components such as foot pedals, steering column, air vents, seat rails, etc. Do not mount the control unit until after setting the internal jumpers and performing a complete operation check of the system. After insta
Summary of the content on the page No. 19
System Wiring 14-Pin Main Harness Pin 1 RED WIRE: +12V Battery Input (15A Fuse). The RED wire must be connected to a clean source of continuous +12V power. Pin 2 WHITE WIRE: Parking Light Output (+/-) relay. Connect the White wire to the circuit that shows +12V or ground only when the parking lights are on and set the internal parking light relay jumper to the proper polarity. For parking light circuits exceeding 10 amps, a relay is required. For vehicle’s with independent left and right parkin
Summary of the content on the page No. 20
Plug-in Connectors 3-Pin White Door Lock Connector: Plug-in connector port for door lock harness or optional door lock relay module. · BLUE WIRE - negative unlock output (-) 500mA. · GREEN WIRE - negative lock output (-) 500mA. 2-Pin Red Connector: Plug-in connector port for LED. Mount the LED in an area where it may be easily seen from either side of the vehicle. 2-Pin Blue Connector: Plug-in connector port for valet switch. Mount the valet switch in an area that is easily accessible from the
