Summary of the content on the page No. 1
ASTRA 7E7
WITH SEPERATE
LOCK/UNLOCK BUTTONS
VEHICLE SECURITY SYSTEM
PRODUCT MANUAL
Summary of the content on the page No. 2
Limited Lifetime Warranty This vehicle security system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid. After the first 12 month warranty period there will be a maximum serv
Summary of the content on the page No. 3
Table of Contents 21. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 2. 2-way LCD Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 2-way LCD Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Adding/Replacing 2-way LCD Transmitters . . . . . . . .
Summary of the content on the page No. 4
Summary of the content on the page No. 5
About Your System Congratulations on your purchase of this State-of-the-Art Vehicle Security System from ScyTek Electronics. With proper installation this system will provide superior protection and performance for many years to come. System Contents: • Main Unit • One 5-Button 2-Way LCD Remote Transmitter • One 5-Button Random Code Remote Transmitter • 2-Way Pager Transceiver Antenna with built in LED light and Valet Switch (See page 23) • High Output 6-tone Siren • Dual Stage Shock Sensor
Summary of the content on the page No. 6
2-way LCD Remote Transmitter Description Button 1 Button 2 Button 3 Button 4 Button 5 The Astra’s 7E7 2-way LCD remote transmitter is offering increased range and confirmation of any activated feature. Page 1 Button 1 Arms and Locks* the system and when held for 5 seconds, activates the system’s Panic feature. Button 1 also locks the doors when the system is in Valet Mode. Button 2 Disarms and Unlocks* the system. Pressing Button 2 again operates the Passenger Unlock feature (if installed). B
Summary of the content on the page No. 7
LCD Transmitter Battery Replacement Your Astra Remote Transmitter uses a 1.5 volt AAA alkaline battery, which will require replacement in time. Depending on the amount of use, the battery may last up to three months before it needs replacement. When the battery needs replacing, the system’s operating range will decrease, the LCD display will show only one of three bars in the battery icon, or the display and sounds may suddenly stop and start as the battery voltage drops below minimum. In order
Summary of the content on the page No. 8
To disable the auto activate function: 1. Press and hold Buttons 2 and 3 until the remote beeps four times. · The fan and clock will be shown indicating timer is activated. 2. Press Button 1 to disable the timer. · The remote will beep three times to indicate the timer has been disabled. LCD Backlight Transmitter Button 5 is used for confirmation, transmitter programming, as well as activation of the LCD backlighting for use in the dark. Press button 5 to activate the LCD backlight. System Conf
Summary of the content on the page No. 9
VLT Valet mode function sets and resets the security system valet mode. * this function is enabled only when the security system is disarmed Set or reset the Valet mode: 1. Press and hold Button 6 until the display shows VLT. · The transmitter will beep six times. 2. Release Button 5. · The LCD panel will play a tone if the Valet mode was set “V" will be displayed indicating that the system is in Valet mode. · The transmitter will beep twice if the Valet mode was reset. “V" will turn off indicat
Summary of the content on the page No. 10
Remote Transmitters Remote Transmitter Description LED Button 1 Button 2 Button 4 Button 3 Button 5 The Astra 7E7 is supplied with one 5-button Remote Transmitter used to control system operations. Button 1 Arms the system and when held for 2 seconds, activates the system’s Panic feature. Button 1 also locks the doors when the system is in Valet Mode. Button 2 Disarms the system. Pressing Button 2 again operates the Passenger Unlock feature (if installed). Button 2 also unlocks the doors when
Summary of the content on the page No. 11
Adding/Replacing One-Way Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below. Note: Up to 4 transmitters can be programmed to operate the system. To erase any previously stored transmitter codes, be sure to program all 4 transmitter memory locations. To program the transmitter(s): 1. Turn on the ignition key On, Off, On, Off, and back On. · The siren will chirp 3 times. 2. Pres
Summary of the content on the page No. 12
System Operation Remote Arming The system monitors 4 independent areas (zones) while armed: doors, hood/trunk, shock sensor and optional sensor input. To Arm the System: 1. Turn off the ignition. 2. Press Button 1. · The siren will chirp once.* · The doors will lock. · The parking lights will flash once. · The LED will turn on, to indicate the starter defeat is activate. 3. 5 seconds after Arming: · The LED will start blinking to indicate that the doors and hood/trunk inputs are being monit
Summary of the content on the page No. 13
Tamper Alert If the system was triggered while away, the LED will flash to indicate which zone triggered the system after disarming and turning on the ignition. The LED indication will repeat 5 times. LED Flashes: 1 flash = optional sensor 2 flashes = shock sensor 3 flashes = not used 4 flashes = door 5 flashes = trunk 10 flashes = main power interrupt or system was reset example: flash-flash-pause-flash-flash-pause = shock sensor Silent Arming/Disarming The system can be programmed to op
Summary of the content on the page No. 14
Panic Mode In the event of an emergency the transmitter’s remote Panic feature can be used to instantly trigger the alarm. To activate the Panic Mode: 1. Press and hold Button 1 for 3 seconds. · The alarm will sound. · The parking lights will flash. · The doors will unlock* allowing access to the vehicle. 2. Press Button 1 or 2 to stop Panic Mode. * If the ignition is on when the Panic feature is activated, the doors will lock for personal safety. Emergency Override If the transmitter become
Summary of the content on the page No. 15
To Emergency Override the system using the code: 1. Follow steps 1-3 above. 2. Press the override switch a number of times equal to the Disarm code, and continue holding for 10 seconds on the last press. · The system will disarm. If the code is entered incorrectly, turn off the ignition and begin again. Automatic Rearming The automatic Rearming feature is designed to protect the vehicle in the event the system is accidentally disarmed. With the Automatic Rearming feature enabled, the alarm w
Summary of the content on the page No. 16
Extended Features Ignition Controlled Door Locks For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on, and unlock the doors after the ignition key is turned off. If a door is open when the ignition is turned on, the ignition locking feature is disabled to protect against locking the keys inside the vehicle. Dome Light Activation If the optional Dome Light Activation feature is i
Summary of the content on the page No. 17
System Installation 1. Thoroughly read and become familiar with the installation instructions before beginning the installation. 2. Review system contents: Main Unit One 5-Button One-Way Remote Transmitter One 5 Button Two-Way LCD Remote Transmitter Siren Shock Sensor Harnesses • 14-Pin main harness • 4-Pin shock sensor harness • 5-Pin door lock harness • LED harness / Receiver Harness/ Valet Switch harness • Starter Disable Harness 3. Verify with the owner, the mounting locations for all vis
Summary of the content on the page No. 18
Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment. Choose a mounting location that will not be easily accessible to a thief, and will not interfere with the operation of any vehicle components such as foot pedals, steering column, air vents, seat rails, etc. Do not mount the control unit until after setting the internal jumpers and performing a complete operation check of the system. After insta
Summary of the content on the page No. 19
System Wiring 14-Pin Main Harness Pin 1 RED WIRE: +12V Battery Input (15A Fuse). The RED wire must be connected to a clean source of continuous +12V power. Pin 2 WHITE WIRE: Parking Light Output (+/-) relay. Connect the White wire to the circuit that shows +12V or ground only when the parking lights are on and set the internal parking light relay jumper to the proper polarity. For parking light circuits exceeding 10 amps, a relay is required. For vehicle’s with independent left and right parkin
Summary of the content on the page No. 20
Plug in Connectors Starter Defeat Connectors Using a volt/ohm meter locate the starter wire (normally a heavier gauge wire) at the ignition switch. This wire will show +12V only during cranking. When this wire is cut the vehicle will be unable to start. Locate the BROWN starter disable wire included with the wiring harness and cut in half. After cutting the vehicle’s Starter circuit wire, connect one half to the cut side of the vehicle’s starter wire coming from the key switch. Connect the
