Summary of the content on the page No. 1
5000RS P PLUS S SERIES
VEHICLE SECURITY SYSTEM
WITH REMOTE START
PRODUCT MANUAL
Summary of the content on the page No. 2
Limited L Lifetime W Warranty This vehicle security system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid. After the first 12 month warranty period there will be a maximum se
Summary of the content on the page No. 3
Table o of C Contents 1. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 2. Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Adding/Replacing Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
Summary of the content on the page No. 5
About Y Your S System The ScyTek Galaxy 5000RS Plus is a combination vehicle security and remote starting system featuring a built-in "ScyNet Network Port" that allows direct connection of optional accessory modules and a PC interface offering expanded system operation. With proper installation this system will provide superior protection and performance for many years to come. The Galaxy 5000RS Plus’ built-in remote start feature is designed to offer maximum convenience by remote starting yo
Summary of the content on the page No. 6
Remote T Transmitters Standard Remote Transmitter Description LED Button 1 Button 2 Button 5 Button 3 Button 4 The Galaxy 5000RS Plus is supplied with two 5-button Remote Transmitters used to control system operations. Note: Using the optional PC or Pocket PC interface with the network software, it is possible to reconfigure the functionality of the transmitter buttons. The standard (default) setting for operation of the transmitters is described below. Button 1 Arms the system and when held
Summary of the content on the page No. 7
Adding/Replacing Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below. Note: Up to 4 transmitters can be programmed to operate the system. To erase any previously stored transmitter codes, be sure to program all 4 transmitter memory locations. To program the transmitter(s): 1. Turn on the ignition key On, Off, On, Off, and back On. (Key On 3 times) · The siren will chirp 3 times
Summary of the content on the page No. 8
Optional 2-way LCD Remote Transmitter Description Button 1 Button 2 Button 3 Button 4 Button 5 The Galaxy 5000RS Plus is compatible with the optional 2-way LCD remote transmitter, offering increased range and confirmation of any activated features. Button 1 Arms and Disarms the system and when held for 2 seconds, activates the system’s Panic feature. Button 1 also locks/unlocks the doors when the system is in Valet Mode. Button 2 Activates the Remote Start feature. Button 3 Activates the Auxi
Summary of the content on the page No. 9
LCD Transmitter Battery Replacement Your Galaxy Remote Transmitter uses a 1.5 volt AAA alkaline battery, which will require replacement in time. Depending on the amount of use, the battery may last up to six months before it needs replacement. When the battery needs replacing, the system’s operating range will decrease, the LCD display will show only one of three bars in the battery icon, or the display and sounds may suddenly stop and start as the battery voltage drops below minimum. In order t
Summary of the content on the page No. 10
System O Operation Remote Arming The system monitors 6 independent areas (zones) while armed: doors, hood, trunk, shock sensor, optional sensor input, and the network port for future expansion. To Arm the System: 1. Turn off the ignition. 2. Press Button 1. · The siren will chirp once.* · The doors will lock. · The parking lights will flash once. · The LED will turn on red, to indicate the starter defeat is activate. 3. 10 seconds after Arming: · The LED will start blinking to indicate that
Summary of the content on the page No. 11
Tamper Alert If the system was triggered while away, the LED will flash to indicate which zone triggered the system after disarming and turning on the ignition. The LED indication will repeat 8 times. LED Flashes (60 seconds): 1 flash = optional sensor 2 flashes = shock sensor 3 flashes = network based sensor 4 flashes = door 5 flashes = trunk 6 flashes = reserved for future use 7 flashes = reserved for future use 8 flashes = reserved for future use 9 flashes = reserved for future use
Summary of the content on the page No. 12
Panic Mode In the event of an emergency the transmitter’s remote Panic feature can be used to instantly trigger the alarm. To activate the Panic Mode: 1. Press and hold Button 1 for 3 seconds. · The alarm will sound. · The parking lights will flash. · The doors will unlock* allowing access to the vehicle. 2. Press Button 2 to stop Panic Mode. * If the ignition is on when the Panic feature is activated, the doors will lock for personal safety. If not deactivated using Button 2, the Panic Mode w
Summary of the content on the page No. 13
To set the Emergency Override Code: 1. Turn on ignition. 2. Within 5 seconds, press the valet switch 5 times. · The siren will provide one long chirp, indicating that you have entered Programming. 3. Press the valet switch 4 times. · The siren will chirp each time the valet switch is pressed. 4. Within 5 seconds, press Button 3 on the transmitter. · The siren will chirp 3 times. 5. Press the valet switch the number of time equal to the desired code (from 1-15). 6. Turn off the ignition then arm
Summary of the content on the page No. 14
Remote S Start F Features Remote Starting To Remote Start the System: 1. Be sure the system is not in Valet Mode. 2. Press and hold Button 4 for three seconds. · The parking lights will turn on. · The LED will flash rapidly. · The engine will start and run for the duration of its programmed Run Time.* · The heater or air conditioner will turn on (if turned on prior to exiting the vehicle). *If the engine fails to start on the first attempt, it will repeat the starting procedure 2 more times.
Summary of the content on the page No. 15
Summary of the content on the page No. 16
Extended F Features Ignition Door Locking For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on. If a door is open when the ignition is turned on, the Ignition Door Locking feature is disabled to protect against locking the keys inside the vehicle. Ignition Door Unlocking For added convenience, this feature automatically unlocks the doors after the ignition key is turned off. If
Summary of the content on the page No. 17
System I Installation 1. Thoroughly read and become familiar with the installation instructions before beginning the installation. 2. Review system contents: Main Unit Two 5-Button Remote Transmitters Siren Shock Sensor Harnesses • 6-Pin starter harness • 20-Pin main harness • 4-Pin shock sensor harness • 3-Pin door lock harness • LED harness • Override Switch harness 3. Verify vehicle is equipped with electronic fuel injection, and starts/idles normally before installation. 4. Determine if veh
Summary of the content on the page No. 18
Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment. Choose a mounting location that will not be easily accessible to a thief, and will not interfere with the operation of any vehicle components such as foot pedals, steering column, air vents, seat rails, etc. Do not mount the control unit until after setting the internal jumpers and performing a complete operation check of the system. After instal
Summary of the content on the page No. 19
System W Wiring 6-Pin Starter Harness Pin 1 RED WIRE A: Main Power Input A (+). Connect to the battery or constant power wire at the ignition switch with a minimum 30 Amp supply. Remove the fuse until the installation is complete and all wiring is checked. Pin 2 RED WIRE B: Main Power Input B (+). Connect to the battery or constant power wire at the ignition switch with a minimum 30 Amp supply. Note: if connecting at the ignition switch it is highly recommended to use separate power wires for
Summary of the content on the page No. 20
Pin 9 BLACK WIRE: Ground Input (-). The Black wire must connect to a solid chassis ground. Clean away any paint or dirt to insure the best possible ground. Pin 10 RED WIRE: Module Power Input (+). Connect to a constant source of +12V. Pin 11 VIOLET WIRE: Positive Door Input (+). Connect to the door switch circuit wire that shows +12V when the door is open. This type of door circuit is usually found on Ford vehicles. Pin 12 GREEN WIRE: Negative Door Input (-). Connect to the door switch cir
