Summary of the content on the page No. 1
3 30 00 00 0P PL LU US S S SE ER RI IE ES S
VEHICLE SECURITY SYSTEM
PRODUCT MANUAL
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Table o of C Contents 1. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 2. Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Adding/Replacing Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
Summary of the content on the page No. 5
About Y Your S System The ScyTek Galaxy 3000 Plus is a state-of-the-art vehicle security system featuring a built-in "ScyNet Network Port" that allows direct connection of optional accessory modules and a PC interface offering expanded system operation. With proper installation this system will provide superior protection and performance for many years to come. System Contents: • Main Unit with built-in ScyNet Network Interface Port • Two 5-Button Random Code Remote Transmitters • High Output
Summary of the content on the page No. 6
Remote T Transmitters Remote Transmitter Description LED Button 1 Button 2 Button 5 Button 3 Button 4 The Galaxy 3000 Plus is supplied with two 5-button Remote Transmitters used to control system operations. Note: Using the optional PC or Pocket PC interface with the network software, it is possible to reconfigure the functionality of the transmitter buttons. The standard (default) setting for operation of the transmitters is described below. Button 1 Arms the system and when held for 2 secon
Summary of the content on the page No. 7
Adding/Replacing Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below. Note: Up to 4 transmitters can be programmed to operate the system. To erase any previously stored transmitter codes, be sure to program all 4 transmitter memory locations. To program the transmitter(s): 1. Turn on the ignition key On, Off, On, Off, and back On. · The siren will chirp 3 times. 2. Press and h
Summary of the content on the page No. 8
System O Operation Remote Arming The system monitors 6 independent areas (zones) while armed: doors, hood, trunk, shock sensor, optional sensor input, and the network port for future expansion. To Arm the System: 1. Turn off the ignition. 2. Press Button 1. · The siren will chirp once.* · The doors will lock. · The parking lights will flash once. · The LED will turn on red, to indicate the starter defeat is activate. 3. 10 seconds after Arming: · The LED will start blinking to indicate that
Summary of the content on the page No. 9
Tamper Alert If the system was triggered while away, the LED will flash to indicate which zone triggered the system after disarming and turning on the ignition. The LED indication will repeat for 20 seconds. LED Flashes (60 seconds): 1 flash = optional sensor 2 flashes = shock sensor 3 flashes = network based sensor 4 flashes = door 5 flashes = trunk 6 flashes = hood (if network remote start module connected) 7 flashes = reserved for future use 8 flashes = reserved for future use 9 flash
Summary of the content on the page No. 10
Panic Mode In the event of an emergency the transmitter’s remote Panic feature can be used to instantly trigger the alarm. To activate the Panic Mode: 1. Press and hold Button 1 for 3 seconds. · The alarm will sound. · The parking lights will flash. · The doors will unlock* allowing access to the vehicle. 2. Press Button 2 to stop Panic Mode. * If the ignition is on when the Panic feature is activated, the doors will lock for personal safety. If not deactivated using Button 2, the Panic Mode w
Summary of the content on the page No. 11
To set the Emergency Override Code: 1. Turn on ignition. 2. Within 5 seconds, press the valet switch 5 times. · The siren will provide one long chirp, indicating that you have entered Programming. 3. Press the valet switch 4 times. · The siren will chirp each time the valet switch is pressed. 4. Within 5 seconds, press Button 3 on the transmitter. · The siren will chirp 3 times. 5. Press the valet switch the number of time equal to the desired code (from 1-15). 6. Turn off the ignition then arm
Summary of the content on the page No. 12
Extended F Features Ignition Door Locking For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on. If a door is open when the ignition is turned on, the Ignition Door Locking feature is disabled to protect against locking the keys inside the vehicle. Ignition Door Unlocking For added convenience, this feature automatically unlocks the doors after the ignition key is turned off. If
Summary of the content on the page No. 13
Remote Sensor Disable When parking the vehicle in areas susceptible to unwanted disturbance from animals or strong weather conditions that could cause the sensors to trigger, the sensor inputs can be temporarily bypassed using the Remote Transmitter, preventing possible false alarms. To disable the sensor inputs : 1. Arm the system normally. 2. Within 5 seconds of Arming the system, press the Arm button again. · The siren will chirp 5 times and the parking lights will flash 5 times to indicate
Summary of the content on the page No. 14
Page 10 - Galaxy 3000 Plus
Summary of the content on the page No. 15
System I Installation 1. Thoroughly read and become familiar with the installation instructions before beginning the installation. 2. Review system contents: Main Unit Two 5-Button Remote Transmitters Siren Shock Sensor Harnesses • 16-Pin main harness • 4-Pin shock sensor harness • 3-Pin door lock harness • LED harness • Override Switch harness • Brown Starter Defeat relay wire 3. Verify with the owner, the mounting locations for all visible components, including the LED and Override switch. 4.
Summary of the content on the page No. 16
Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment. Choose a mounting location that will not be easily accessible to a thief, and will not interfere with the operation of any vehicle components such as foot pedals, steering column, air vents, seat rails, etc. Do not mount the control unit until after setting the internal jumpers and performing a complete operation check of the system. After insta
Summary of the content on the page No. 17
System W Wiring 16-Pin Main Harness Pin 1 BROWN WIRE: Siren Output (+) 3A. The Brown wire must connect to the siren’s red wire. The Black siren wire must be grounded. Pin 2 BLACK WIRE: Ground Input (-). The Black wire must connect to a solid chassis ground. Clean away any paint or dirt to insure the best possible ground. Pin 3 ORANGE WIRE: Armed Output (–) 500mA. The Orange wire provides a ground output while armed to activate a optional circuit disable relay or other device such as a powe
Summary of the content on the page No. 18
Starter Defeat Connectors Using a volt/ohm meter locate the starter wire (normally a heavier gauge wire) at the ignition switch. This wire will show +12V only during cranking. When this wire is cut the vehicle will be unable to start. Locate the BROWN starter disable wire included with the wiring harness and cut in half. After cutting the vehicle’s Connect one half to the cut side vehicle’s starter wire coming from the key switch. Connect the other BROWN wire to the wire going to the starter.
Summary of the content on the page No. 19
Jumper S Settings Jumper Selections Carefully separate the top and bottom halves of the main unit case. Once the cover is removed, the polarity jumpers will be visible next to the parking light and dome light relays. Set the jumpers for the correct polarity output as described below, then reassembly the main unit case. Parking Light Output. Selects the polarity (+/-) for the output of the on-board Parking Light relay. Left Pin + Center Pin = positive Right Pin + Center Pin = negative Dome
Summary of the content on the page No. 20
System P Programming Entering System Programming To enter System Programming: 1. Turn on ignition. 2. Within 5 seconds, press the valet switch 5 times. · The siren will provide one long chirp, indicating that you have entered Programming. 3. Press the valet switch the number times equal to the System Parameter you want to change. · The siren will chirp each time the valet switch is pressed. 4. Within 5 seconds, press the transmitter button corresponding to the desired operating mode for that Sys
