Summary of the content on the page No. 1
49-851.fm Page 1 Thursday, August 19, 1999 10:56 AM
Cat. No. 49-851
OWNER’S MANUAL
Please read before using this equipment.
TD-1500
Auto Theft Deterrent System
Summary of the content on the page No. 2
49-851.fm Page 2 Thursday, August 19, 1999 10:56 AM INTRODUCTION The TD-1500 Auto Theft Deterrent System is a starter disable module that helps prevent auto theft or unauthorized vehicle use. It quickly connects to your vehicle’s ignition system, and has an easy-to-use remote for arming and disarming. The armed indicator shows when the system is on, to deter would-be thieves from attempting to break in. BEFORE YOU BEGIN It is important that you know where to find constant power, vehicle groun
Summary of the content on the page No. 3
49-851.fm Page 3 Thursday, August 19, 1999 10:56 AM INCLUDED ITEMS Your TD-1500 includes the following items. Be sure you have all items before you begin installation. Wiring Harness Main System Status Indicator with Bracket and Harness Disarm Two-Button Remote Double-Sided Tape Wire Ties Wire Tap-In Connectors 3
Summary of the content on the page No. 4
49-851.fm Page 4 Thursday, August 19, 1999 10:56 AM INSTALLING THE SYSTEM As you install the system, see the “Wiring Diagram” on Page 11. CONNECTING TO THE STARTER WIRES The starter wire connects the ignition switch to the starter so- lenoid. Follow these steps to find this wire. 1. Using the starter solenoid’s color coded wires as a guide, locate the wire that goes from your vehicle’s ignition (key) switch to the solenoid. This wire is usually found under the dashboard where the wires conne
Summary of the content on the page No. 5
49-851.fm Page 5 Thursday, August 19, 1999 10:56 AM 4. Start your vehicle. The test light should light or the meter should indicate voltage only while the engine is crank- ing (not while it is stopped or running). 5. If the test fails, contact the Auto Security Helpline at 1- 800-598-2527 for assistance in finding the correct wire. 6. Turn off the engine. Then cut the wire you located in Steps 2–4 at a point where there are several inches of wire on each side of the cut. Note: If you cut the
Summary of the content on the page No. 6
49-851.fm Page 6 Thursday, August 19, 1999 10:56 AM CONNECTING TO POWER 1. Touch the negative lead from a 12-volt test light or DC voltmeter to a metal part of your vehicle and use the pos- itive lead (with a wire-piercing probe adapter) to probe for an existing wire that has 12 volts when your vehicle’s ignition is off. 2. Use one of the supplied wire tap-ins to connect the sys- tem’s red wire to the wire you located in Step 1, then replace the fuse. 3. Connect the system’s black wire to a m
Summary of the content on the page No. 7
49-851.fm Page 7 Thursday, August 19, 1999 10:56 AM 2. If you are using the supplied bracket, clean the mounting surface with denatured alcohol and allow it to dry. Peel the backing off of one side of the double-sided tape and press it onto the bottom of the bracket. Then peel off the adhesive backing from the other side of the tape and press the bracket onto the dash. If you are mounting the indicator in the dash’s front 5 panel, drill a /16-inch hole at the selected location, tak- ing care
Summary of the content on the page No. 8
49-851.fm Page 8 Thursday, August 19, 1999 10:56 AM USING THE SYSTEM ACTIVATING THE REMOTE CONTROL You must train the system to respond to the supplied remote control. To activate the remote control, immediately after ap- plying power, press DISARM on the remote. The system beeps twice. If the system loses power, the system stops responding to the remote. To reactivate it, simply press DISARM on the re- mote after power is restored. Your system can learn two remote codes if you want to add a
Summary of the content on the page No. 9
49-851.fm Page 9 Thursday, August 19, 1999 10:56 AM CARE AND MAINTENANCE To enjoy your starter kill module for a long time: • Keep the module dry. If it gets wet, wipe it dry immedi- ately. • Handle the module gently and carefully. Don’t drop it. Modifying or tampering with the starter kill module’s internal components can cause a malfunction and invalidate its war- ranty. If your starter kill module is not performing as it should, take it to your local RadioShack store for assistance. REPLAC
Summary of the content on the page No. 10
49-851.fm Page 10 Thursday, August 19, 1999 10:56 AM SPECIFICATIONS System Power . . . . . . . . . . . . . . . . . . . . . . . . 9–16 Volts DC Current Draw . . . . . . . . . . . . . . . . . . . . . . 22 mA (Disarmed) Pulsed 40 mA (Armed) Maximum Switched Current . . . . . . . . . . . . . . . . . . 30 Amps Remote Control Battery . . . . . . . . . . . . . . . . . . . . . . . 12 Volt 3 3 1 Size (HWD) . . . . . . . . . . . . 3 /8 × 2 /8 × 1 /8 Inches (System) 11 5 1 2 /16 × 1 /16 × /2 Inches
Summary of the content on the page No. 11
49-851.fm Page 11 Thursday, August 19, 1999 10:56 AM WIRING DIAGRAM Power Harness Yellow — Antenna Red — +12 Volts Black — Ground To the To the Ignition Switch Starter Solenoid Cut the wire going from the Ignition Switch to the Starter Solenoid. 11 Status Indicator White — To Starter Red/Black — To Switch
Summary of the content on the page No. 12
49-851.fm Page 12 Thursday, August 19, 1999 10:56 AM RadioShack Limited Warranty This security product is warranted against manufacturing defects in material and workmanship for ninety (90) days from the date of pur- chase from RadioShack company owned stores and authorized RadioShack franchisees and dealers. Within this period RadioShack will repair the security product without charge for parts and labor. Simply bring your RadioShack sales slip as proof-of-purchase date to any RadioShack sto
