Summary of the content on the page No. 1
RS900 / RS901 SERIES V
OPERATING INSTRUCTIONS
CONGRATULATIONS on your choice of a CoolStart™ Remote Engine Starter by Crimestopper Security Products Inc.
This booklet contains the information necessary for using & maintaining your remote start system. If any questions
arise, contact your installation dealer or Crimestopper Security Products Inc. at (800) 998-6880.
**IMPORTANT NOTES:- RS901 MODEL**
RS901 Model is an add-on/expansion unit, without remote
Summary of the content on the page No. 2
TABLE OF CONTENTS Operation Cautions & Warnings…….……………..….…………………………………….……………………………2 Using the Remote Transmitter…………………………………………………………………………………..….…….3 Remote Engine Control…………….…..…………………………………………………………………….………….3-7 Convenience and Safety Features……………………………….……………………………………...……..………8-9 Transmitter Programming….…………….……………………………………………….………………………...……10 2 Vehicle Operation.…………………………………….………………...……………………..…………….…………11 Troubleshooting “Before You Call” Section……………..…………
Summary of the content on the page No. 3
USING THE REMOTE TRANSMITTER (RS900) The transmitter supplied with this system has Four (4) buttons / channels. The button configuration is Factory-set and unchangeable. (RS901 model does not include remote transmitters: For add-on / OEM use only) #2 UNLOCK #1 LOCK #5 CAR 1-2 START #3 TRUNK #4 REMOTE START TRANSMITTER BUTTONS REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - SUCCESSFUL START: 1) Press and release the remote start button. (For RS901 models, activate Green Start inp
Summary of the content on the page No. 4
SOLID FLASH 1X AFTER IGN START 3 STARTER SEC. THEN SOLID REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - UNSUCCESSFUL START In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then attempts nd rd to restart the engine a 2 and 3 time. For hard starting engines, the unit will allow a starter crank time of up to13 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to 13 seconds to help preven
Summary of the content on the page No. 5
START IDLE DOWN MODE: This mode allows the unit to take over operation of the parked vehicle while the ignition key is removed and you exit the vehicle. The vehicle is put into a remote running condition before you exit and it will remain running for the programmed run time or until you come back. Examples: • You pull up to a convenience store for a quick stop, "Idle Down" mode keeps engine running when you exit the vehicle, (with keys in hand) remote lock doors or arm alarm. When you r
Summary of the content on the page No. 6
SOLID IGN START OFF UNLOCK ENTERING A VEHICLE DURING “IDLE-DOWN” or “INFINITY RUN” MODES: 1) With engine running in "IDLE DOWN" (parking lights ON), unlock door via remote or key. 2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset) 3) Turn Ignition to ON/RUN position, then depress brake pedal to reset the Remote Starter. Parking lights will turn off indicating the Remote Start is OFF and Vehicle is running by the Key. Drive away as normal. FLASH 2X
Summary of the content on the page No. 7
2) Parking Lights will start flashing, and doors will unlock. 3) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running. 4) The vehicle’s parking lights will flash for the programmed run time of 12, 24, or 36, or 48 minutes and then switch to solid while motor runs indefinitely or until fuel supply runs out. IGN START OFF FLASH FOR PROGRAMMED 2X RUN TIME, THEN SOLID TIMED 4 HOUR SELF START MODE This mode allows the vehicle to be programmed to self-sta
Summary of the content on the page No. 8
6) The vehicle will Start by itself every 4 hours until driven with key or started via the remote control. SOLID START LIGHTS OFF 5 SEC. WITHIN 10 SEC. UNLOCK PRESS 1X FLASH 4X IGN START OFF LOCK CONVENIENCE AND SAFETY FEATURES KEYLESS ENTRY (POWER DOOR LOCK CONTROL, Optional) This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) through the transmitter for safety and convenience. Note: This feature may require extra labor and/or p
Summary of the content on the page No. 9
the remote control must still be utilized to operate the Starter disable feature. REMOTE PANIC (When used with Optional HORN HONK) For personal safety this unit now includes a panic feature. To sound the vehicle car horn, press the Lock Button on the remote for more than 2 seconds. The vehicle horn will honk along with flashing parking lamps for 1 minute. Reset Remote Panic by pressing either the lock or unlock button. HORN CHIRP/HONK OUTPUT (Optional: with Horn connection/Horn option
Summary of the content on the page No. 10
of an external relay. This system must be programmed to allow the relay to work as a starter disable. PASSIVE STARTER DISABLE (Optional) This RS900 includes a programmable feature to allow the Optional Starter Disable to activate automatically 1 minute after the ignition is turned off. This programmable feature may provide insurance discounts or meet an insurance requirement in your providence. HOOD OPEN SAFETY (Requires grounding hood pin installation) Prevents the engine being Remo
Summary of the content on the page No. 11
th and 4 flashes for the 4 code. If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise turn key off and close hood. See diagram below. TRANSMITTER PROGRAMMING: IGN OFF WAIT FOR (GRAY WIRE GROUNDED) 4 FLASHES PRESS 4X's IGN OFF START FLASH 2, 3, or 4 X's RS900 V 2-VEHICLE OPERATION The RS-900 V system can be used for 2 car operation. A single RS900V remote can control two independent vehicles with RS900 V systems installed. SETUP: See dia
Summary of the content on the page No. 12
CAR I / CAR II OPERATION CAR I Slide START CAR II RS 900 V TROUBLESHOOTING: “BEFORE YOU CALL” SECTION UNIT WILL NOT ATTEMPT A START (KEYLESS ENTRY STILL FUNCTIONS NORMALLY): The unit is in Valet mode. Turn Ignition ON, press and hold valet/programming button for 6 seconds then turn key off. Unit is now out of valet mode and should perform a remote start. If optional LED indicator is installed, then i
Summary of the content on the page No. 13
NO RESPONSE FROM REMOTE TRANSMITTERS: (4 Parts) 1. Check for proper power/ground wiring connections at module. 2. Check Antenna Module connection. The antenna module included with this system must be plugged in. 3. Transmitters may need to be programmed to the unit. See transmitter programming steps on Page 10. 4. Check transmitter Batteries and replace if necessary. UNIT CRANKS VEHICLE BUT ENGINE NEVER STARTS: (2 parts) 1. In extreme cold or severe weather conditions, the unit may t
