Summary of the content on the page No. 1
EZ-30DP/31DP/33DP/34DP
1-WAY SYSTEM
DP SERIES II (Data Port)
OPERATING INSTRUCTIONS
**IMPORTANT NOTES:- FOR EZ-30DP MODEL ONLY**
EZ-30DP Model is an add-on/expansion unit, without remotes or an antenna that must be controlled by an existing
alarm or keyless entry system. The “Infinity Run” feature is not available on an EZ-30DP system. Most of the
remote start features can be controlled through an existing factory or aftermarket remote keyless entry or alarm
system. Pressing an au
Summary of the content on the page No. 2
TABLE OF CONTENTS Operation Cautions & Warnings…….……………..….…………………………………….…………………………2 Using the Remote Transmitter…………………………………………………………………………………...…….3 Status LED……………………………………………………………………………………………………………….4 Remote Engine Control…………….…..…………………………………………………………………….……….3-8 Turbo Timer Mode……………………………….……………………………………...……….………………………9 Convenience and Safety Features……………………………….……………………………………...……..…10-11 Transmitter Programming….…………….…………………………………………….…………………………....…12 2 Veh
Summary of the content on the page No. 3
USING THE REMOTE TRANSMITTER #2 #2 #1 UNLOCK UNLOCK REMOTE START #1 #1 LOCK LOCK FLASHLIGHT FLASHLIGHT FLASHLIGHT VEHICLE 2 VEHICLE 2 VEHICLE 2 #3 TRUNK EZ START EZ START EZ START #3 #4 REMOTE REMOTE START EZ-34DP II START EZ-31DP II EZ-33DP II For EZ-30DP II The EZ-30DP II model does not include remote transmitters, as it is designed for the expansion of a “parent” remote keyless or alarm system. For EZ-31DP II The transmitter supplied with this system has 1 button, flashlight and ca
Summary of the content on the page No. 4
STATUS LED LED Operation: (install option) LED will flash when remotely locking your doors. LED will remain solid in Valet Service mode. REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - SUCCESSFUL START: 1) Press the remote start button for at least 1/2 second (*default). (For EZ-30DP II models, consult your installer). 2) Parking lights flash once, return solid, and the Ignition/Acc circuits turn on. 3) After a few seconds the Starter Motor engages. The parking lights and Acc circui
Summary of the content on the page No. 5
REMOTE ENGINE CONTROL TURNING OFF A REMOTE STARTED ENGINE: 1) Engine is running in Remote Start (Parking lights ON). 2) Press and release the remote start button or double press (If option #6 is on). (For EZ-30DP II model, activate Green Start input wire.) 3) Engine & parking lights OFF, Doors re-lock/re-arm. ENTERING YOUR REMOTE STARTED VEHICLE: 1) With engine running, Unlock system with remote (If equipped) or open door with key. 2) Enter vehicle and be careful not to step on br
Summary of the content on the page No. 6
REMOTE ENGINE CONTROL IDLE DOWN MODE - EXITING THE VEHICLE: 1) With vehicle engine running with key, press the Remote Start button for at least one second or twice if set for Double press (For EZ-30DP II model activate Green remote start input wire.) 2) Parking Lights will turn ON. 3) Doors will unlock, or if brake pedal is being depressed, doors will unlock when it is released. 4) Turn OFF Ignition and remove key. Engine should remain running. 5) Exit vehicle then remote lock doors if
Summary of the content on the page No. 7
REMOTE ENGINE CONTROL INFINITY RUN MODE (NOT AVAILABLE ON EZ-30DP II MODEL) This mode can only be activated when "Idle Down" procedure. The Infinity Run mode allows the vehicle engine to remain running INDEFINITELY after the programmed run time elapses. This mode will allow the vehicle to be left running and unattended without the ignition key in the switch preventing the vehicle from being stolen. This mode can be beneficial to law enforcement or commercial trucks that need to remai
Summary of the content on the page No. 8
REMOTE ENGINE CONTROL SELECTABLE HOURLY COLD-START MODE – EXITING THE VEHICLE: 1) Engine should be running with the Key. Press the Remote Start button for at least 1 second. (For EZ-30DP II model, activate Green start input wire.) Lights will turn on signaling the remote start has turned on and doors will unlock. 2) Within 10 seconds press and release the valet/program button once for each hourly increment (1 time = 1hour, 2X = 2 hours, 3X = every 3 hours, 4X = every 4 hours). 3) Par
Summary of the content on the page No. 9
TURBO TIMER MODE (OPTIONAL) The optional Turbo Timer mode allows the EZ Start system to keep a Turbo or Turbo Diesel vehicle running for 1 to 5 minutes [selectively] after you remove the key, exit the vehicle, and lock the doors remotely. This is handy for turbo cool-down without the need for expensive turbo timers. This mode requires the use of an extra part called a momentary switch/button that is not included with the kit. Check with your installer about adding this feature. NOTE:
Summary of the content on the page No. 10
CONVENIENCE AND SAFETY FEATURES KEYLESS ENTRY (POWER DOOR LOCK CONTROL, Optional) This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) via remote control for safety and convenience. Note: This feature may require extra labor and/or parts to install. Press the Lock or Unlock transmitter button as you leave or come near the vehicle. Parking lights will flash once for lock and twice for unlock. If vehicle is running by the remote start sy
Summary of the content on the page No. 11
CONVENIENCE AND SAFETY FEATURES VALET MODE / STARTER DISABLE OVERRIDE Before servicing your vehicle or handing the keys over to a Valet we recommend putting the unit into valet mode. The remote start function WILL NOT operate when in Valet mode. To enter Valet mode, turn the key to the ON position, press and hold Program/Valet switch for 5-6 seconds. The LED will turn on solid and the system is now in valet. Perform this procedure again to exit of Valet mode. The keyless entry will s
Summary of the content on the page No. 12
TRANSMITTER PROGRAMMING Note: All transmitter codes must be learned at time of programming!! The EZ-34 learns up to 4 different transmitter codes. 1. Turn key to the ON position. (Pink wire must be connected.) 2. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. 3. Press button #1 of the transmitter to be coded. You should get 2 light flashes indicating the unit is waiting for a nd rd 2 code, then press button #1 of a second
Summary of the content on the page No. 13
2-VEHICLE OPERATION & PROGRAMMING A single EZ-30 SERIES II remote can control two different vehicles with EZ-30 SERIES II systems installed. SETUP: Follow the “Transmitter Programming” steps on the second vehicle below. Program Car #2’s existing remotes, then quickly press the Car #2 side button on your remote before pressing the lock button on your remote to program it to Car VEHICLE #2 #2. Once your remote is programmed to the second Press side button vehicle, press the car #2 si
Summary of the content on the page No. 14
TROUBLESHOOTING: “BEFORE YOU CALL” SECTION UNIT WILL NOT ATTEMPT A START (KEYLESS ENTRY STILL FUNCTIONS NORMALLY): The unit is in Valet mode. Turn Ignition ON, press and hold valet/programming button for 6 seconds then turn key off. Unit is now out of valet mode and should perform a remote start. If optional LED indicator is installed, then it will be on solid when in Valet and OFF when out of Valet. UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START: The unit senses a fault
Summary of the content on the page No. 15
TROUBLESHOOTING: “BEFORE YOU CALL” SECTION VEHICLE STARTS BUT “CHECK ENGINE” LIGHT COMES ON OR ENGINE RUNS BADLY: (2 parts) 1. Many 1995-UP General Motors cars/trucks require a secondary ignition circuit for the Transmission computer and other on board systems. If the vehicle is started without this wire energized, there may be a “Check Engine” or “Service Engine Soon” light on the dash. This may cause damage if the vehicle is driven in this condition. Check with installer to see if thi
Summary of the content on the page No. 16
REMOTE START DIAGNOSTICS If the system flashes the parking lights one to three times and doesn’t attempt remote, it means the following: 1 Parking Light Flash = Problem with Brake Switch. 2 Parking Light Flashes = Problem with Hood Switch. 3 Parking Light Flashes = Valet Service Mode. www.crimestopper.com ONLINE TECHNICAL SUPPORT Phone (800) 998-6880 www.crimestopper.com/techweb05.html FAX (805) 581-9500 © 2006 Crimestopper Security P
