Summary of the content on the page No. 1
Summary of the content on the page No. 2
Table of Contents Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Using Your XL2000 Security System . . . . . . . . . . . . . . . . . . . . . . . 3 4-Button/4-Channel Remote Control . . . . . . . . . . . . . . . . . . . . . 3 How to Interpret the Chirps and Parking Light Flashes . . . . . . . . . . . 4 How to Interpret the LED Status Indicator . . . . . . . . . . .
Summary of the content on the page No. 3
Standard Features ● FACT™ — False Alarm Control and Test — eliminates recurring false alarms ● Lifetime Warranty ● $3,OOO Theft Protection Guarantee (see guarantee card for details) ● 4-Button/8-Channel Remote Control ● AntiScan™ — blocks electronic scanners from disarming the alarm ● Multiple-Car Control — allows you to command several alarms with the same remote ● MultiRemote™ Recognition — useful for other drivers, since the system will ac- cept up to 4 Clifford remote controls of any types
Summary of the content on the page No. 4
Using Your XL2OOO Security System 4-Button/8-Channel Remote Control The 4-button/8-channel remote control is a miniature radio transmitter with a range of up to 100 feet. Obstructions, interference or a weak battery will reduce the range. The remote control is the key to your security system. It is a user-friendly device that transmits eight distinct and unique digital codes: channels 1-4 with the red slide switch in the up position, and channels 5-8 with the switch down. Use it to arm or disarm
Summary of the content on the page No. 5
TO ACTIVATE AN As previously noted, button II (switch up) can control another OPTION WHEN option when the system is disarmed. This is most commonly THE ALARM IS used for an optional remote trunk release. DISARMED . . . . . . . TO ACTIVATE AN Button IV (switch up) and I-IV with the switch down, may ac- OPTION tivate another remote controlled option, such as the Clifford In- REGARDLESS OF telliStart™ (remote engine starter accessory), electric garage ALARM STATE . . . . . door or another Cliff
Summary of the content on the page No. 6
Secured Valet Mode Whenever the alarm is put in secured valet mode, all of the alarm functions are bypassed since it prevents AutoArming and accidental activation of the alarm. You should use the valet mode whenever your car is either to be serviced by mechanics, handed over to car wash personnel or driven by valet attendants. It also comes in handy if you ever lose your remote control or its battery dies. If you have the AutoArming feature set on, when fueling your car, either put the alarm in
Summary of the content on the page No. 7
Smart AutoTesting™ Each time you remotely arm your vehicle, it will perform a series of tests on all triggers and sensors. If a trigger malfunction is found, you will be visually and audibly alerted immediately with 4 chirps and flashes instead of the usual 2. If a sensor is malfunctioning, you will receive the usual 2 chirps and flashes, then, a few seconds later, there will be 4 chirps and flashes. Specific Malfunction Identification: The system not only tells you if the prob- lem is a trigger
Summary of the content on the page No. 8
FACT™— False Alarm Control and Test With FACT, you’ll never experience repeated false alarms. If your six-sound siren goes off, DO NOT remotely disarm the system while the siren sounds; allow it to run for the full siren duration. Before sounding the siren a second time, the system automatically checks for another activated trigger. Should the siren sound again, you will know for sure that someone is tampering with your vehicle. (To disable FACT, see User-Selectable Features on pages 9-10.) Dual
Summary of the content on the page No. 9
AntiScan Car thieves use electronic scanners that rapidly transmit one remote control code after another to defeat ordinary alarms. AntiScan prevents scanners from disarming your system. Automatic Fault-Proof Starter Interrupt The system automatically prevents engine starting while the system is armed but allows you to start it even in the unlikely event of a full system failure (other manufacturer’s alarms may leave you stranded). Multi-Level Chirp Control Whenever you wish, you may lower the v
Summary of the content on the page No. 10
User-Selectable Features Your XL2000 vehicle security system allows you to set many of its features to your own personal preferences. We have made the programming procedures very simple: to make a change, you just flick the valet switch a few times. The system comes from the factory with all of its features pre-programmed as noted in the table below and on page 10. To change any of the settings, use the procedure noted. To restore the feature to its factory setting, just repeat the procedure: 1.
Summary of the content on the page No. 11
# of Program Factory Secondary flicks & completion Feature setting action Result chirps confirmation 1 chirp 3 Siren Change duration from 30 10 30 sec. — seconds after Duration to 60 seconds or vice-versa last step 1 chirp 3 Tampering Change state from 11 OFF — seconds after Warning OFF to ON or vice-versa last step FACT — 1 chirp 3 False Alarm Change state from 12 ON — seconds after Control and OFF to ON or vice-versa last tap Test Add a New Button I/channel 1 code of Remote to Press remote c
Summary of the content on the page No. 12
User-Programmable Remote Controls Your system will respond to as many as four remote controls regardless of each remote control’s individual digital coding. Thus, you can buy additional remote controls, including the super-high-security 4.3-billion-code Premier™ remote controls, from any Authorized Clifford Dealer. To add a new remote control to the system, use the procedures noted in the User-Selectable Features section on pages 9-10. To Erase Unwanted Remote Control Codes If your remote contro