Summary of the content on the page No. 1
MS2007.qxd 09/24/2002 1:24 PM Page 1
Summary of the content on the page No. 2
MS2007.qxd 09/24/2002 1:24 PM Page 2 ongratulations on your purchase of this Ungo System. Please read this manual thoroughly to familiarize yourself with your Csystem’s components and operation. Discuss any questions you might have with your installing dealer. Record the serial number of your Ungo System and keep all dealer records and receipts. Be sure to discuss the installation with the dealer so that you understand the specifics of the installation in your vehicle. CAUTIONS • USE OF T
Summary of the content on the page No. 3
MS2007.qxd 09/24/2002 1:24 PM Page 3 Table of Contents 1. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1 2. Remote Transmitters Remote Transmitter Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Optional Driver Door Priority Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Battery Replacement . . . . . . . . . . . .
Summary of the content on the page No. 4
MS2007.qxd 09/24/2002 1:24 PM Page 4
Summary of the content on the page No. 5
MS2007.qxd 09/24/2002 1:24 PM Page 1 About Your Ungo System The Ungo MS2007 is a state-of-the-art combination vehicle security and remote controlled car starter system. The MS2007 offers security features designed to deter and detect potential intrusions to your vehicle. It will alert and inform the driver and people in the vicinity of your vehicle when a zone is violated. The MS2007 will inform the user of any defective zones while arming, and in the event that the system is triggered, the M
Summary of the content on the page No. 6
MS2007.qxd 09/24/2002 1:24 PM Page 2 Remote Transmitters Remote Transmitter Layout LED Button 1 I II III Button 3 Button 2 IV Button 4 The Ungo MS2007 comes with a multi-function LCD Remote Transmitter featuring two-way communication with the vehicle. Each time a transmitter button is pressed, the LED will flash and the transmitter will beep to indicate that a transmission is taking place. If the transmitter is within two-way communication range, the LCD will display the status of the syste
Summary of the content on the page No. 7
MS2007.qxd 09/24/2002 1:24 PM Page 3 2. Press transmitter Button 2 to set the hour. 3. Press transmitter Button 3 to set the minutes. Hold Button 3 to advance the minutes rapidly. • The hour will be displayed followed by either an “A” or “P” to indicate AM or PM. 4. Press transmitter Button 4 to save the time setting. • The transmitter will play a tune to confirm the time is set. Setting the Alarm Clock The built-in alarm clock function that plays an alert tone when . To set the Alarm Clock
Summary of the content on the page No. 8
MS2007.qxd 09/24/2002 1:24 PM Page 4 2. Press and hold the Valet switch for 2-3 seconds. • The status LED and parking lights will flash 3 times. 3. Release the program switch. 4 Press Button 3* on each Remote Transmitter. 5. Turn off the ignition. Any transmitters that were previously learned to this system and not included in this procedure will no longer operate this system. Additional Remote Transmitters Additional Remote Transmitters for your MS2007 are available from your Author
Summary of the content on the page No. 9
MS2007.qxd 09/24/2002 1:24 PM Page 5 MS2007 Owner’s Manual - Page 5
Summary of the content on the page No. 10
MS2007.qxd 09/24/2002 1:24 PM Page 6 Security Features Remote Arming When Armed, the system monitors and protects 3 independent areas, or zones, including the doors, hood/trunk, and shock sensor. To Arm the system: 1. Turn off the ignition. 2. Press Button 1. • The siren/horn will chirp once.* • The doors will lock. • The parking lights will flash once. • The LCD will show and . • The LED will turn on red, indicating the doors, hood and trunk inputs are activated. * The siren chirp(s) du
Summary of the content on the page No. 11
MS2007.qxd 09/24/2002 1:24 PM Page 7 • The LCD will show and . • The LED will turn off. * The siren chirps and light flashes during disarming will alert you if the system had been triggered while armed. 2 chirps / 2 flashes = normal disarming 3 chirps / 3 flashes = Tamper Alert - system was triggered ** If the Passenger Unlock Feature is installed, pressing Button 2 will unlock only the driver’s door. Pressing the unlock Button 2 again unlocks all doors. Tamper Alert On Disarming, if the
Summary of the content on the page No. 12
MS2007.qxd 09/24/2002 1:24 PM Page 8 Passive Arming When the Arming Mode has been set for Passive Arming, the system arms itself automatically, each time the ignition is turned off and all of the doors, hood and trunk are closed. To start the Passive Arming Process: 1. Turn off the ignition.* • The status LED will begin to flash quickly. 2. Open the door and exit the vehicle. • Once all doors are closed and the dome light is turned off, the LED will turn off. 3. After 20 seconds, • The
Summary of the content on the page No. 13
MS2007.qxd 09/24/2002 1:24 PM Page 9 Emergency Override In case your Remote Transmitter becomes inoperable, or it is lost or stolen, you can still enter and drive your car by using the following procedure. Be sure that you have your ignition keys ready and that you know the location of the Override switch before you perform this procedure. To override the system: 1. Unlock the door using the key. 2. Enter the vehicle. • Because the system is armed, the system will trigger and the siren wi
Summary of the content on the page No. 14
MS2007.qxd 09/24/2002 1:24 PM Page 10 Remote Start Features Remote Starting To Remote Start the System: 1. Be sure the System is not in Valet Mode. 2. Press Button 4. • The LCD will show . • The parking lights will turn on. • The siren will chirp 3 times (if the system is Armed, the shock sensor will turn off). • The ignition will turn on. • The engine will start and run for the duration of its programmed Run Timer.* • The heater or air conditioner will turn on (if turned on prior to exiting
Summary of the content on the page No. 15
MS2007.qxd 09/24/2002 1:24 PM Page 11 3. Release the brake pedal. 4. Remove the key from the ignition switch. 5. You may now exit the vehicle, arm the alarm and lock the doors. To re-enter the vehicle and resume driver control: 1. Disarm the alarm by pressing Button 2 on the Remote Transmitter.* • The doors will unlock.* 2. Turn on the ignition. 3. Press the brake pedal to disengaged the MS2007. • The LED will turn off. *If optional keyless entry feature is installed. Auto Cold Starting T
Summary of the content on the page No. 16
MS2007.qxd 09/24/2002 1:24 PM Page 12 Other Features Valet Mode Allows you to temporarily disable the security system when the car is being service or turned over to a parking attendant. To turn Valet Mode on or off: 1. Turn on the ignition. 2. Press and hold the override switch. 3. While holding the override switch, turn off the ignition. • The siren will chirp once to indicate you have turned Valet Mode on. • The siren will chirp twice to indicate you have turned Valet Mode off. 4. Release
Summary of the content on the page No. 17
MS2007.qxd 09/24/2002 1:24 PM Page 13 Auxiliary Function This function will operate regardless of whether the system is armed or disarmed. To operate the auxiliary function, press Button 3. • The LCD will show . Remote Sensor Bypass The system can be set up so that in case of extreme weather conditions (such as high winds), the shock sensor can be temporarily bypassed using the Remote Transmitter, while the system is armed, to prevent false alarming. To Bypass the sensors: 1. After arming
Summary of the content on the page No. 18
MS2007.qxd 09/24/2002 1:24 PM Page 14 Notes Page 14 - MS2007 Owner’s Manual
Summary of the content on the page No. 19
MS2007.qxd 09/24/2002 1:24 PM Page 15 Reference Chart You can use this chart to quickly identify and interpret your system’s chirp indications and LED flashes. Output When Status 1 chirp arming normal arming 1 + 4 chirps arming door, hood, or trunk is open 2 chirps arming Valet Mode is on LED double flashes Valet Mode Starter Defeat Activated 2 chirps disarming normal disarming 3 chirps disarming Tamper Alert - system was triggered 1 LED flash after Tamper Alert door 2 LED flashes after Ta
Summary of the content on the page No. 20
MS2007.qxd 09/24/2002 1:24 PM Page 16 System Indications You can use these tables to quickly identify and interpret the MS2007’s parking light and LED indications. Status LED Indications Parking Light Indications Flashes Functions Flashes Functions Slow System is Armed 1 System is Armed Rapid Remote Started/Running 2 System is Disarmed Solid Valet mode 3 Auto Cold Starting engaged Double Auto Cold Starting engaged Triple System Armed & Remote Started Technical Data FCC ID: Specifications MP6
