Summary of the content on the page No. 1
1
2
Diablo /AMX 68/AT-58 Owner's Manual 12/29/97
Summary of the content on the page No. 2
Summary of the content on the page No. 3
þ In te rior Light Il lu mi na tion Ca pa bil ity — When remotely disarmed , the alarm system turns on the interior lights for 30 seconds or until the ignition key is turned on (requires an optional relay). Multi- Zone Pro tec tion — Offers full perimeter security with separate þ trigger connections for the doors, hood and trunk (may require optional switches). Pre vi ous In tru sion Alert — Audibly warns you if the alarm was þ triggered while you were away. Spe cific In tru sion Iden ti fi ca t
Summary of the content on the page No. 4
þ Re mote Con trol Door Lock Ca pa bil ity — Allows you to lock and unlock your doors without using your key (may require optional relays). User Pro gram ma ble Pas sive Door Lock ing — Allows you to þ program the system to automatically lock the doors every time the alarm passively arms. þ Key less En try in Valet Mode — Allows you to control your door locks or activate an optional accessory while in valet mode (may require optional relays). Chan nel 2 Ac ces sory Out put — Allows you to add a
Summary of the content on the page No. 5
Operating Instructions n Remote Control — Each of the pair of remote controls is a miniature radio transmitter with a typical range of up to 100 feet. Obstructions, radio interference, cellular transmissions or a weak remote control battery may reduce the range or interrupt transmission. (If the system does not immediately respond, release and press the button again. This works better than holding the button down.) The second remote can be used by a second driver, or kept as a spare. n To Arm Th
Summary of the content on the page No. 6
n To Silently Arm or Disarm the System — Press remote button #3 for 1-2 seconds. n Si lent Arm In di ca tions. The parking lights will flash twice, the doors will lock, the starter will be disabled and the LED will flash slowly. n Si lent Dis arm In di ca tions. The parking lights will flash once, the doors will unlock, the starter will be enabled and the LED will turn off. n Interior Light Illumination Capability — When the alarm system is remotely disarmed, the vehicle's interior light(s) wi
Summary of the content on the page No. 7
n Turn off Valet Mode 1. Turn your ignition key to the "ON" position or start the vehicle. 2. Flick the valet switch to the "OFF" position. 3. The LED will turn off to indicate the alarm is no longer in Valet Mode. n User Programmable Passive Door Locking — The system will not automatically lock the doors when the alarm passively arms to prevent the keys and remote from accidentally being locked in the ve hi cle. If you pre fer, you can eas ily pro gram the alarm to auto mati cally lock the do
Summary of the content on the page No. 8
Summary of the content on the page No. 9
n How to Interpret the Chirps and Parking Light Flashes ─ When you press the remote control buttons, the system will respond with chirps (unless you have the chirp muting feature turned on or the system is in Valet Mode) and flashes of the parking lights to indicate the system status. An explanation of these chirp/flash acknowledgments is as follows: Num ber of chirps and flashes Meaning 1 Disarming of the alarm 2 Arming of the alarm 2 and then 4 Armed and there is a sensor malfunction (automati
Summary of the content on the page No. 10
Programming Alarm System Features All programmable alarm features are accomplished by turning the ignition key on (or starting the vehicle) and flicking the valet switch on and off a preset number of times. 1. Remove the alarm from Valet Mode. Programming cannot be accessed while the alarm is in Valet Mode, indicated by the LED on solid red. 2. Select the feature you wish to program from the "Programming Table for Alarm Features." Note the number of chirps. 3. Turn the ignition key to the "ON"
Summary of the content on the page No. 11
Summary of the content on the page No. 12
Pro gram ming Ta ble for Re mote Controls continued Fac tory # of Fea ture Re mote Con trol Sec on dary Ac tion Set ting Chirps All Channel Press button #1. The siren will chirp 1 time. Remote — 12 Learn control will operate at factory preset order. Instant Code Wait 3 seconds. The siren will chirp twice. All remote — 13 Deletion controls are erased from memory. 12 2 Diablo /AMX 68/AT-58 Owner's Manual 12/29/97
Summary of the content on the page No. 13
© Copyright 1998 Avital Technologies, Inc. 31-1241/98 13 2 Diablo /AMX 68/AT-58 Owner's Manual 12/29/97
