Summary of the content on the page No. 1
3-251-485-11(1)
FM/AM Compact Disc Player
CDC-X237
Owner’s Record
For your convenience, record the serial number (you will find
them on the bottom side of your set) in the space provided
below. Please refer to them when you contact your AIWA
dealer in case of difficulty.
Model No. CDC-X237 Serial No.
2003 Sony Corporation
Summary of the content on the page No. 2
PRECAUTIONS TABLE OF CONTENTS THEFT PROTECTION .............................................. 2 •Use only in a 12-volt DC negative-ground electrical BASIC OPERATION, AUDIO AND CLOCK system. ADJUSTMENT ..................................................... 2 •Disconnect the vehicle’s negative battery terminal RADIO OPERATION ................................................. 3 while mounting and connecting the unit. CD PLAYER OPERATION ........................................ 4 •When replacing the
Summary of the content on the page No. 3
THEFT PROTECTION BASIC OPERATION, Take the front panel with you when leaving the car, and AUDIO AND CLOCK keep it in the supplied carrying case. ADJUSTMENT Detaching the front panel PWR/ATT Before detaching the front panel, remove the CD to SEL prevent possible damage to the unit. Jog dial (PUSH-SOURCE) 1 Press z to remove the CD. 2 Press and hold PWR/ATT until the unit turns off. 3 Press %. (Hold the panel with one hand to prevent accidentally dropping it.) 4 Remove the panel. DSPL TU (TUNER) +
Summary of the content on the page No. 4
Adjusting sound Setting the clock You can select the following modes for adjusting sound 1 Press and hold DSPL until the clock indicator depending on the music you listen to: BASS (low flashes on the display. frequencies), TRE (high frequencies), BAL (left/right), 2 Press + (to set hour) or – (to set minute), and then FAD (front/ rear) and H-BASS (high bass). turn Jog dial. 1 Press SEL repeatedly to select the mode to be 3 Press DSPL. adjusted. Pressing SEL cycles through the modes. The Displayi
Summary of the content on the page No. 5
Monaural mode Presetting stations manually When signals become weak, or FM reception becomes (Manual Memory) poor, the unit automatically switches to Monaural mode 1 Press TU (TUNER) repeatedly to select the desired to reduce noise. band (FM1, FM2, FM3, AM1, or AM2). Local mode 2 Press + or – to tune in to a desired station (see Local mode allows you to tune in only to strong stations “Tuning in to a station” as well for another tuning during Seek Tuning. method). 1 Press LO before you start see
Summary of the content on the page No. 6
Note Labeled-side up During Shuffle Play, pressing r allows you to skip only to the beginning of the current track, not to the previous track. AUXILIARY EQUIPMENT Track number Listening to a cassette/MD/MP3 portable player or other equipment You can listen to equipment connected to the unit. Refer to the operating instructions for the corresponding equipment for more detailed information. Elapsed playing time CD indicator Be sure to remove inserted CDs to prevent possible damage to the unit befo
Summary of the content on the page No. 7
TROUBLESHOOTING SPECIFICATIONS RADIO SECTION Error code (FM) In the following cases the corresponding error code Frequency Range: 87.5 MHz – 108 MHz indication appears. Follow the suggestions below to Usable Sensitivity: 12.7 dBf solve such problems. 50 dB Quieting Sensitivity: 17.2 dBf IF Rejection: 100 dB E03 Focus error. Check that the CD is loaded properly Frequency Response: 30 Hz – 15,000 Hz (right side up, etc.), and the CD contains valid S/N Ratio: 70 dB data. Stereo Separation: 35 dB at
Summary of the content on the page No. 8
http://www.aiwa.com/ Sony Corporation Printed in Thailand LIMITED WARRANTY Aiwa Strategic Accounts Partnership Inc. (“Aiwa”) warrants to the original consumer purchaser that this product is free of defects in material and workmanship at the time of purchase. WARRANTY PERIODS During the applicable LABOR warranty period, Aiwa will pay labor and service charges for the repair of defects or, at its option, will replace a defective product with a new or remanufactured equivalent product. During the
