Summary of the content on the page No. 1
In-Ground Basketball System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A.
Write Model Number
WARNING!
From Box Here:
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO PROPERTY.
Toll-Free Customer Service Number for U.S: 1-800-334-9111
Internet Address: http://www.hydra-rib.com
05/05 ID# M866041
1
Summary of the content on the page No. 2
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN WARNING SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and FAILURE TO FOLLOW THESE WARNINGS MAY RESULT follow these rules for safe operation of the system. IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. To ensure safety, do not attempt to assemble this system without following the Owner must ensur
Summary of the content on the page No. 3
PARTS LIST Item Qty. Part No. Description 1 1 968860 Pole 2 1 998850 Plate, Anchor, Black 3 1 Rim Assembly 4 1 Net 5 4 203017 Nut, Hex, 3/8-16 6 4 203300 Washer, Locking, 3/8 7 2 250001 Bolt, Hex, Tap, 3/8-16 x 4” Long 8 4 250002 Bolt, Hex, Tap, 3/8-16 x 2” Long 9 1 203457 Label, Logo, Vinyl, 2.3” x 2.7” 10 1 Backboard 11 1 200685 Label, Height Adjustment 12 1 204940 Screw Jack 11 13 2 220563 Screw, 1/4-20 x 1/2” Long, Rim Cover 14 1 808545 Rod, Spacer, 19.8”, Zinc 15 1 203641 Bolt, Hex, 1/2-13
Summary of the content on the page No. 4
HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #23 (1) Item #13 (2) Item #20 (1) Item #8 (2) Item #7 (2) Item #29 (4) Item #34 (4) HARDWARE IDENTIFIER (NUTS, WASHERS & SPACERS) Item #28 (3) Item #22 (10) Item #33 (4) Item #21 (16) Item #24 (9) Item #25 (13) Item #26 (1) Item #5 (4) HARDWARE IDENTIFIER (OTHER) Item #37 (1) Item #35 (1) Item #36 (1) ID# M866041 05/05 4
Summary of the content on the page No. 5
Ensure ground is level with playing surface, then dig pole hole. 1. 24" (61 cm) 48" (121.9 cm) WARNING! 24" (61 cm) GROUND SURFACE PLAYING SURFACE 48" (121.9 cm) CONTACT UTILITIES BEFORE DIGGING. 2. Install nut (25) to J-bolt (19) as shown. Repeat procedure 25 25 for remaining three J-bolts 2.75” 2 (19). (7 cm) IMPORTANT!: 19 25 Make sure nuts (25) are 2.75” (7 cm) from top of J-bolts Install threaded ends of J-bolts (19) through holes 3. in mounting plate (2) and secure as shown. 19 NOTE: Mak
Summary of the content on the page No. 6
Fill hole with concrete. Tamp down concrete to release air pockets 4. and build drainage hill. DRAINAGE HILL 1" (2.54 cm) PLAYING SURFACE SIDE VIEW Insert J-bolts (19) from mounting plate (2) into cement as shown. Move assembly around to release 5. any air pockets in cement, then rest mounting plate on cement drainage hill. Apply some pressure to level mounting plate on top of drainage hill. Level mounting plate and square with playing surface. Clean off any exc
Summary of the content on the page No. 7
Insert bushings (27) into areas 6. shown. 27 10 27 27 27 27 27 27 27 27 27 1 27 17 27 27 18 27 27 27 05/05 ID# M866041 7
Summary of the content on the page No. 8
Rest top of pole on a piece of scrap wood (not included) and line up holes in pole to holes in 7A. mounting plate (2) as shown. WARNING! PLAYING SURFACE THREE PEOPLE SCRAP WOOD REQUIRED FOR THIS (NOT INCLUDED) PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 2 PLAYING SURFACE Insert bolt (15) through holes in plate and pole and secure with nut (22). 7B. 1 15 22 ID# M866041 05/05 8
Summary of the content on the page No. 9
8. WARNING! TWO people are required to lift pole into position so that the rod (14) can be installed and secured by the THIRD person. While pole is being supported by TWO THREE PEOPLE capable adults, position rod (14) and lock REQUIRED FOR THIS into place with hitch pin (36) and cotter PROCEDURE. FAILURE pin (37). TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY Slide barrel washer (35) onto other end of AND/OR PROPERTY rod (14) and secure with washer (24) and DAMAGE. nut (25). Tighten u
Summary of the content on the page No. 10
9. While still in forward position, attach both upper and lower yokes (17 & 18) to pole as shown. WARNING! THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 22 21 17 18 21 28 ID# M866041 05/05 10
Summary of the content on the page No. 11
Attach elevator adjustment (12) to 10. lower yoke (18). WARNING! THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 18 22 21 12 26 21 20 05/05 ID# M866041 11
Summary of the content on the page No. 12
Attach elevator adjustment (12) to pole bracket. 11. WARNING! THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 21 21 23 22 33 33 12 ID# M866041 05/05 12
Summary of the content on the page No. 13
Attach backboard (10) to upper and lower 12. yokes (18 & 17). Then, hinge board to match up with holes in A. B. First attach board (10) to upper yoke (17), lower yoke (18), FIG. C, and secure with using TWO people to hold the board and hardware as shown in FIG. D. ONE person to attach hardware (FIG. A). Use hardware as shown in FIG. B. WARNING! THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. FIG. A FIG. C FIG. D 1
Summary of the content on the page No. 14
Remove rim cover (16), attach rim assembly (3) to backboard (10) and 13. reattach rim cover (16). IMPORTANT!: ** For rim assembly see instructions included with rim. Carefully cut and peel protective film away from board prior to attaching rim. 5 6 10 Rim Assembly 3 Refer To Instructions Included With Rim Hardware For Rim Assembly. 8 7 ID# M866041 05/05 14
Summary of the content on the page No. 15
10 9 87 14. Set-up For Left Side Set-up For Right Side Apply height indicator A. 30 30 labels (32 & 31) to height indicators (30). 10 10 9 7 9 87 8 31 10 10 32 7 9 8 9 87 Attach height indicators to lower yoke in area shown by tapping B. screws (29) into place with a rubber mallet. IMPORTANT!: 29 NOTE ORIENTATION OF HEIGHT INDICATORS: 10’ MARK SHOULD FACE AWAY FROM BACKBOARD. 29 Install net (4) to rim as shown. 15. 1. 2. 4. 3. 05/05 ID# M866041 15 10 9 78
Summary of the content on the page No. 16
Upright pole (1) by tightening nut (25). 16. Using 3/4” wrench, turn nut (25) clockwise to begin standing pole upright. Continue to turn nut (25) until pole has come to rest against washers (24) and pole is vertical. Once pole is in its final position, install washers (24) and nuts (25) onto J-bolts (19) and fully tighten to secure pole to base plate 1 WARNING! THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY 25 AND/OR PROPERTY 1 DAMAGE.
Summary of the content on the page No. 17
After pole has been secured to plate (2) loosen nut 17. (25), remove cotter pin (37), and pull out pin (36). This will allow the removal of the assembly bolt (14) which is no longer necessary for the remainder of the assembly and installation of system. WARNING: ONLY AFTER NUTS (24) HAVE BEEN FULLY TIGHTENED: Remove cotter pin (37) and pin (36) to remove assembly bolt (14) from bottom plate (2). 25 24 35 14 37 36 05/05 ID# M866041 17
Summary of the content on the page No. 18
18. Apply height adjust ment label (11). Adjust system by turning crank until desired height is reached per height indicator (30). WARNING! READ AND UNDERSTAND WARNING & HEIGHT ADJUSTMENT LABELS BEFORE USING THIS UNIT. FAILURE TO FOLLOW 30 OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY. 10 feet 12 (3.05 m) 11 ID# M866041 05/05 18
Summary of the content on the page No. 19
LIMITED LIFETIME WARRANTY ® Subject to proper installation and normal use, Hydra-Rib warrants, subject to limitations below, to the original retail ® purchaser all structural components of the Hydra-Rib system to be free of defects in material and workmanship for the duration of ownership by the original retail purchaser. Mercahndise must be shipped prepaid with a copy of proof of purchase to our factory for examination to see whether it needs to be repaired or replaced. Any labor costs, travel
