Summary of the content on the page No. 1
MODEL T100H
UV FLUORESCENCE SO ANALYZER
2
Addendum to T100 Operation Manual, PN 06807
© TELEDYNE ADVANCED POLLUTION INSTRUMENTATION
9480 CARROLL PARK DRIVE
SAN DIEGO, CA 92121-5201
USA
Toll-free Phone: 800-324-5190
Phone: 858-657-9800
Fax: 858-657-9816
Email: api-sales@teledyne.com
Website: http://www.teledyne-api.com/
Copyright 2011 PN 07265A DCN6038
Teledyne Advanced Pollution Instrumentation 25 March 2011
Summary of the content on the page No. 2
Summary of the content on the page No. 3
SAFETY MESSAGES Important safety messages are provided throughout this manual for the purpose of avoiding personal injury or instrument damage. Please read these messages carefully. Each safety message is associated with a safety alert symbol, and are placed throughout this manual; the safety symbols are also located inside the instrument. It is imperative that you pay close attention to these messages, the descriptions of which are as follows: WARNING: Electrical Shock Hazard HAZAR
Summary of the content on the page No. 4
Teledyne API - T100H Addendum to T100 Operation Manual CONSIGNES DE SÉCURITÉ Des consignes de sécurité importantes sont fournies tout au long du présent manuel dans le but d’éviter des blessures corporelles ou d’endommager les instruments. Veuillez lire attentivement ces consignes. Chaque consigne de sécurité est représentée par un pictogramme d’alerte de sécurité; ces pictogrammes se retrouvent dans ce manuel et à l’intérieur des instruments. Les symboles correspondent aux consignes suiv
Summary of the content on the page No. 5
WARRANTY WARRANTY POLICY (02024D) Prior to shipment, T-API equipment is thoroughly inspected and tested. Should equipment failure occur, T-API assures its customers that prompt service and support will be available. COVERAGE After the warranty period and throughout the equipment lifetime, T-API stands ready to provide on-site or in-plant service at reasonable rates similar to those of other manufacturers in the industry. All maintenance and the first level of field troubleshooting are
Summary of the content on the page No. 6
Teledyne API - T100H Addendum to T100 Operation Manual This page intentionally left blank. vi 07265A DCN6038
Summary of the content on the page No. 7
ABOUT THIS ADDENDUM This T100H addendum, PN 07265, is to be used in conjunction with the T100 manual, PN 06807; it is comprised of multiple documents, in PDF format, as listed below. Part Rev Name/Description No. 07265 A T100H Addendum to T100 Manual Appendix A Menu Trees (Refer to Appendix A of the T100 manual for 05244 B related software documentation). 06928 2011Mar24 Spare parts List (in Appendix B, this Addendum) 04527 2011Mar24 Recommended Spares Stocking Levels (in Appendi
Summary of the content on the page No. 8
This page intentionally left blank. viii 07265A DCN6038
Summary of the content on the page No. 9
TABLE OF CONTENTS 1. INTRODUCTION...............................................................................................................................11 1.1. T100H Documentation ............................................................................................................11 1.2. Using This Manual Addendum.......................................................................................................11 2. SPECIFICATIONS, APPROVALS & WARRANTY ...............
Summary of the content on the page No. 10
TABLE OF CONTENTS Teledyne API - T100H Addendum to T100 Operation Manual 10.3.2. Sensor Module Repair & Cleaning...........................................................................................47 10.3.2.1. Adjusting the UV Lamp (Peaking the Lamp).........................................................................48 10.3.2.2. PMT Hardware Calibration (FACTORY CAL) ........................................................................50 10.4. Technical Assistance .............
Summary of the content on the page No. 11
1. INTRODUCTION This addendum is based on the Model T100 Operators Manual (P/N 06807). In most ways the T100H analyzer is identical to the T100 in design and operation, therefore most of the basic set up information, operating instructions as well as calibration, maintenance, troubleshooting and repair methods are found in that manual. This addendum documents only those areas where the T100H is different in design or operating method from the T100. 1.1. T100H Documentation NOTE T
Summary of the content on the page No. 12
Introduction Teledyne API - T100H Addendum to T100 Operation Manual) Operation Instructions This section includes step by step instructions for operating the analyzer and using its various features and functions. Calibration Procedures General information and step by step instructions for calibrating your analyzer. Instrument Maintenance Description of preventative maintenance procedures that should be regularly performed on you instrument to assure good operating condition. Theory o
Summary of the content on the page No. 13
2. SPECIFICATIONS, APPROVALS & WARRANTY 2.1. Specifications Table 2-1: Model T100H Basic Unit Specifications Min/Max Range Min: 0-10 ppm Full scale (Physical Analog Output) Max: 0-5,000 ppm Full scale (selectable, dual ranges and auto ranging supported) 3 Measurement Units ppm, mg/m (user selectable) 1 Zero Noise 0.1 ppm (RMS) 1 Span Noise < 1% of reading (RMS) above 10 ppm 2 Lower Detectable Limit 0.2 ppm Zero Drift (24 hours) < 1 ppm Span Drift (24 hours) < 0.5% fo full
Summary of the content on the page No. 14
Specifications, Approvals & Warranty Teledyne API - T100H Addendum to T100 Operation Manual) 2.2. CE Mark Compliance Emissions Compliance The Teledyne Advanced Pollution Instrumentation UV Fluorescence SO Analyzer was tested and found to be 2 fully compliant with: EN61326 (1997 w/A1: 98) Class A, FCC Part 15 Subpart B Section 15.107 Class A, ICES-003 Class A (ANSI C63.4 1992) & AS/NZS 3548 (w/A1 & A2; 97) Class A. Safety Compliance The Teledyne-Advanced Pollution Instrumentation UV Fluo
Summary of the content on the page No. 15
3. GETTING STARTED 3.1. Unpacking and Initial Setup CAUTION To avoid personal injury, always use two persons to lift and carry the Model T100H. WARNING Ensure that the power source voltage and frequency match those of the instrument specs on the rear panel model label. Never disconnect electronic circuit boards, wiring harnesses or electronic subassemblies while the unit is under power. CAUTION – Avoid Warranty Invalidation Printed circuit assemblies (PCAs) are sensitive to
Summary of the content on the page No. 16
Getting Started Teledyne API - T100H Addendum to T100 Operation Manual) 3.1.1. Electrical Connections: For full details on the electrical connections of the T100H, please refer to the T100 user’s manual (#06807), Electrical Connections section. 3.1.1.1. External Pump The T100H is equipped with an external pneumatic pump. This pump is powered separately from the instrument via it’s own power cord. The pump has no ON/OFF switch and should begin operating as soon as it is plugged into a li
Summary of the content on the page No. 17
Teledyne API - T100H Addendum to T100 Operation Manual Getting Started 3.2. Pneumatic Connections NOTE To prevent dust from getting into the analyzer, it was shipped with small plugs inserted into each of the pneumatic fittings on the rear panel. Make sure that all dust plugs are removed before attaching exhaust and supply gas lines. Store for future use. Table 3-1: Inlet / Outlet Connector Descriptions REAR PANEL FUNCTION LABEL Connects the sample gas to the analyzer. When ope
Summary of the content on the page No. 18
Getting Started Teledyne API - T100H Addendum to T100 Operation Manual) 3.2.1.2. Connections with Internal Valve Options Installed There is no IZS option available for the T100H . An additional valve option (Option 50C - Zero & Two Span Points) is available on the T100H. The pneumatic set up for this option is: On/Off Source of Valves SAMPLE Gas VENT here if input is pressurized PUMP Sample Exhaust High Span Point Chassis Lo w Span Point External Zero Zero Air Filter Air Sc
Summary of the content on the page No. 19
Teledyne API - T100H Addendum to T100 Operation Manual Getting Started 3.2.2. T100H Layout EXHAUST GAS OUTLET PMT UV LAMP PUMP REACTION CELL UV Detector SAMPLE Particulate GAS INLET Filter CRITICAL FLOW ORIFICE 3 700 cm /min @ 7 In-Hg-A SAMPLE VACUUM PRESSURE PRESSURE SENSOR SENSOR FLOW CONTROL & PRESSURE SENSOR INSTRUMENT CHASSIS Figure 3-3: Internal Pneumatic flow for T100H in Basic Configuration 19 07265A DCN6038
Summary of the content on the page No. 20
Getting Started Teledyne API - T100H Addendum to T100 Operation Manual) Figure 3-4: T100H Layout (Basic Unit – No Valve Options) 20 07265A DCN6038
