Summary of the content on the page No. 1
9
7 8
5 6
4
1 2 3
0
NCR 7455 Retail Terminal
Release 1.0
Site Preparation
18427
B005-0000-1286
Issue A
Summary of the content on the page No. 2
The products described in this book are licensed products of NCR Corporation. NCR is a registered trademark of NCR Corporation. Pentium is a registered trademark of Intel Corporation. It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software, and firmware become available. NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of
Summary of the content on the page No. 3
Site Preparation i Preface Audience This book is written for hardware installer/service personnel, system integrators, and field engineers. Notice: This document is NCR proprietary information and is not to be disclosed or reproduced without consent. Safety Warnings This equipment is intended for use with an IT power system with a line-to- line voltage of 240 V or less. Fuse Replacement Caution: For continued protection against risk of fire, replace only with the same type and ratings of fuse.
Summary of the content on the page No. 4
ii Site Preparation Lithium Battery Warning Caution: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type as recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. Attention: Il y a danger d'explosion s'il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d'un type recommandé par le constructeur. Mettre au rébut les batteries usagées conformément aux in
Summary of the content on the page No. 5
Site Preparation iii This book contains the information necessary for the preparation of a site that conforms to NCR specifications. It is very important that the site complies with the requirements specified in the document because, once the equipment has been installed, deficiencies in site preparation or the problems caused by these deficiencies are much more difficult to detect and correct. Further, failure to comply with these requirements or to take proper steps to protect equipment agains
Summary of the content on the page No. 6
iv Site Preparation Finally, only the customer can know the full extent of damage that may be caused to his business by reason of failure of the equipment which is to be installed. For this reason, it is the customer’s responsibility to ascertain the extent of any possible damage to his existing or planned business, and to effect full insurance in for all eventualities. References • NCR 7455 Retail Terminal User’s Guide (B005-0000-1285) • NCR 7455 Retail Terminal Service Guide (B005-0000-1339) •
Summary of the content on the page No. 7
Site Preparation v Table of Contents Introduction.........................................................................1 Interpreting the Model Number.......................................2 Related Site Preparation Data ...........................................3 How to Order ......................................................................4 Customer Responsibilities 5 AC Store Wiring Requirements
Summary of the content on the page No. 8
vi Site Preparation NCR 5972 2x20 Remote Post Customer Display....17 NCR 5973 International Remote Post Customer Display.........................................................................18 NCR 5972 Remote Table-Top Customer Display ..19 NCR 2336-K007 External CD-ROM Drive ..............20 NCR 2336-K008 USB RS-232 Port Server ................20 Component Weights.........................................................21 Ventilation Clearance.................................................
Summary of the content on the page No. 9
Site Preparation vii AC Power Line Transient Protection 1 Data Line Transient Protection .........................................2
Summary of the content on the page No. 10
viii Site Preparation Revision Record Issue Date Remarks A April 01 First issue
Summary of the content on the page No. 11
Site Preparation ix Radio Frequency Interference Statements Federal Communications Commission (FCC) Information to User This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
Summary of the content on the page No. 12
x Site Preparation Declaration of Conformity NCR Corporation Manufacturer’s Name NCR Corporation Manufacturer’s Address Retail Solutions Division 2651 Satellite Boulevard Duluth, GA 30096-5810 Information Technology Equipment Type of Equipment Class 7455 Model Number 100-240 V, 2.0 A, 50-60 Hz Electrical Ratings (Input) NCR Corporation, 1700 South Patterson Boulevard, Dayton, OH 45459, USA, declares that the equipment specified above conforms to the referenced EU Directives and Harmonized Stand
Summary of the content on the page No. 13
9 8 7 6 4 5 1 2 3 0 Site Preparation Introduction 18427 This document provides the information necessary to prepare a site to NCR specifications prior to installing a terminal. The site must be properly prepared before the retail terminal is installed because site preparation deficiencies may be difficult to detect and correct after installation. The terminal consists of separate pieces that may be combined in a variety of configurations. Certain combinations are mutually exclusive. You must det
Summary of the content on the page No. 14
2 Site Preparation Interpreting the Model Number NCR Model 74xx 22 XX 80 01 Language 01 = International English Power Required 80 = 110 -240 VAC 50/60 Hz Operating System 00 = No OS 01 = Windows 03 = MS/DOS Processor 22 = Base Unit with 12.1" LCD (Release 1) 18043
Summary of the content on the page No. 15
Site Preparation 3 Related Site Preparation Data AC Power and Communications Wiring Title Order Number NCR Ethernet Communications Wiring Guide BST0-2118-82 NCR Terminal AC Power Wiring Guidelines BST0-2115-53 Peripherals Title Order Number NCR 7158 Thermal Receipt/Impact Printer B005-0000-1112 NCR 7162 Thermal Receipt Printer Owner’s Guide B005-0000-1067 NCR 7166 Thermal Receipt/Impact Printer B005-0000-1002 NCR 7194 Thermal Receipt Printer Owner’s Guide B005-0000-1094 NCR 7196 Thermal Receipt
Summary of the content on the page No. 16
4 Site Preparation How to Order Information Products are available through several different channels. You need an order form if you are using fax, e-mail, or mail order. Order forms are available to NCR personnel through QuickLook. In QuickLook, click on Forms & Templates, then select Information Products Order Form. Web Sites • http://inforetail.AtlantaGA.NCR.COM (NCR only) • http://www.info.NCR.COM (Anyone) Online Order • Connect System (NCR only) Phone Order • 800-543-2010 (US area) • 622-37
Summary of the content on the page No. 17
Site Preparation 5 Customer Responsibilities Before the system can be installed, the customer must do or provide the following: • When required by NCR, provide the NCR Customer Services representative with appropriate drawings that indicate: − Location of the equipment − Site wiring (power and communications, paths and lengths) − Location of other equipment that may generate electrical noise, electromagnetic interference, or heat. • Make building alterations necessary to meet wiring and other si
Summary of the content on the page No. 18
6 Site Preparation AC Store Wiring Requirements The customer must provide suitable AC power for the retail terminals, associated equipment, and devices. A dedicated unswitched power line dedicated to the NCR equipment installation is recommended. Refer to the Workstation and Peripherals AC Wiring Guide (BSTO- 2115-53) for store AC wiring requirements. The AC outlet must be installed near the retail terminal and easily accessible to the operator. LAN Communications The terminal supports Ethernet
Summary of the content on the page No. 19
7 8 9 4 5 6 1 2 3 0 Site Preparation 7 System Configuration Diagram NOTE: 7837 connect Serial Only to RS-232 or Wedge 7837 7448 Customer 5972-1000 5972-2000 Display Customer Customer Display Display 5973 International Customer Display PS/2 or USB Keyboard CRT Operator or Customer Display Parallel/ VGA PS/2 LCD Wedge * NOTE: 7158 & 7196 connect Serial KBD to RS-232 or USB Aux Aux Power Power RS-232 Transaction Printers Parallel * * USB 7194 7196 7166 7158 7455 7162 Cash Drawer LAN
Summary of the content on the page No. 20
8 Site Preparation Physical Considerations This section presents the following retail terminal information: • Operating and service clearance requirements • Display mounting considerations • Retail terminal and component dimensions • Component weights • Airflow requirements • Power requirements
