Summary of the content on the page No. 1
IM605
July, 1997
Square Wave TIG 175
For use with machines having Code Numbers: 10456
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However, your
overall safety can be increased by
proper installation ... and thoughtful
operation on your part. DO NOT
INSTALL, OPERATE OR REPAIR
THIS EQUIPMENT WITHOUT
READING THIS MANUAL AND
THE SAFETY PRECAUTIONS
CONTAINED THROUGHOUT.
And, most importantly, think before
you act and be careful.
OPERATOR’
Summary of the content on the page No. 2
i i SAFETY WARNING CALIFORNIA PROPOSITION 65 WARNINGS For Diesel Engines: Diesel engine exhaust and For Gasoline Engines: The engine exhaust from some of its constituents are known to the State this product contains chemicals known to the of California to cause cancer, birth defects, and State of California to cause cancer, birth defects, other reproductive harm. or other reproductive harm. ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHIL
Summary of the content on the page No. 3
ii ii SAFETY ELECTRIC SHOCK can kill. ARC RAYS can burn. 3.a. The electrode and work (or ground) circuits 4.a. Use a shield with the proper filter and cover are electrically “hot” when the welder is on. plates to protect your eyes from sparks and Do not touch these “hot” parts with your bare the rays of the arc when welding or observing skin or wet clothing. Wear dry, hole-free open arc welding. Headshield and filter lens gloves to insulate hands. should conform to ANSI Z87. I standards. 3.b. In
Summary of the content on the page No. 4
iii iii SAFETY WELDING SPARKS can CYLINDER may explode cause fire or explosion. if damaged. 6.a. Remove fire hazards from the welding area. 7.a.Use only compressed gas cylinders If this is not possible, cover them to prevent containing the correct shielding gas for the the welding sparks from starting a fire. process used and properly operating Remember that welding sparks and hot regulators designed for the gas and materials from welding can easily go through small cracks pressure used. All hos
Summary of the content on the page No. 5
iv iv SAFETY zones où l’on pique le laitier. PRÉCAUTIONS DE SÛRETÉ 6. Eloigner les matériaux inflammables ou les recouvrir afin de Pour votre propre protection lire et observer toutes les instructions prévenir tout risque d’incendie dû aux étincelles. et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- 7. Quand on ne soude pas, poser la pince à une endroit isolé de antes: la masse. Un court-circuit accidental peut provo
Summary of the content on the page No. 6
v v for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ��� Thank You as much pride as we have in bringing this product to you! Please Examine Carton and Equipment For Damage Immediately When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims for material damaged in shipment must be made by the purchaser against the transportation company at the time the shipment
Summary of the content on the page No. 7
vi vi TABLE OF CONTENTS Page SAFETY .........................................................................................................................i-iv INSTALLATION SECTION .................................................................................................1 TECHNICAL SPECIFICATIONS......................................................................................1 SELECT SUITABLE LOCATION ................................................................................
Summary of the content on the page No. 8
1 1 INSTALLATION TECHNICAL SPECIFICATIONS - Square Wave TIG 175 (K1582-1 only) INPUT - SINGLE PHASE ONLY Standard Input Current at Code Voltage Rated Output Number 240/380/415/1/50/60 54/33/30 AC/DC Stick & DC TIG, 71/41/37 AC TIG 10456 Additional Lincoln Rating 220-240/400-415/1/50/60 54/30 AC/DC Stick & DC TIG, 71/37 AC TIG RATED OUTPUT Duty Cycle Amps Volts at Rated Amperes GTAW 25% Duty Cycle 150 14.8 V AC/DC 40% Duty Cycle 125 14.5 V AC/DC 60% Duty Cycle 110 14.3 V AC/DC 100% Duty Cycle 85
Summary of the content on the page No. 9
2 2 INSTALLATION Read entire installation section before starting MACHINE GROUNDING AND HIGH FRE- installation. QUENCY INTERFERENCE PROTECTION Safety Precautions The welder must be grounded. See your local and national electrical codes for proper grounding methods. WARNING The high frequency generator, being similar to a radio ELECTRIC SHOCK can kill. transmitter, can be blamed for radio, TV and electronic � Only qualified personnel should equipment interference problems. These problems perform
Summary of the content on the page No. 10
3 3 INSTALLATION Refer to the Technical Specifications page at the begin- a) A metal underground water pipe in direct contact ning of this section. Fuse the input circuit with the recom- with the earth for ten feet or more. 1 mended super lag fuses or delay type circuit breakers. Using fuses or circuit breakers smaller than recommended b) A 3/4” (19mm) galvanized pipe or a 5/8” (16mm) may result in “nuisance” shut-offs from welder inrush currents solid galvanized iron, steel or copper rod driven
Summary of the content on the page No. 11
4 4 INSTALLATION INPUT LEADS L1 & L2 USE Electrode/Gas Output Receptacle on the front of the INSULATED BARREL RING TERMINALS TO FIT #10-32 welder and turn it clockwise until it is tight. This is a STUDS PROVIDED. quick connect terminal and also provides the gas con- nection for the shielding gas to the torch.
WARNING (DO NOT To avoid receiving a high frequency shock, keep the REMOVE) TIG torch and cables in good condition. __________________________________________ WORK
Summary of the content on the page No. 12
5 5 INSTALLATION REMOTE CONTROL CONNECTION A remote control receptacle is provided on the case front of the welder for connecting a remote control to tm to the machine. A Foot Amptrol , foot activated remote control, is included with the Square Wave TIG 175. Refer to the Optional Accessories section of this man- ual for other available remote controls. CONNECTIONS FOR STICK (SMAW) WELDING STICK ELECTRODE CABLE AND WORK CABLE CONNECTION Refer to Included Equipment in the Operation Section of this
Summary of the content on the page No. 13
6 6 OPERATION SAFETY PRECAUTIONS GENERAL DESCRIPTION Read and understand this entire section before operat- The Square Wave TIG 175 is a constant current, single ing the machine. range AC/DC TIG (GTAW) arc welding power source with built-in arc starter / stabilizer. It also has stick welding (SMAW) capability. The Square Wave TIG 175 is recommended for the WARNING TIG (GTAW) and stick (SMAW) welding processes within its output capacity of 12 to 175 amps, on both ELECTRIC SHOCK AC and DC polarit
Summary of the content on the page No. 14
7 7 OPERATION CONTROLS AND SETTINGS All operator controls and adjustments are located on the front of the Square Wave TIG 175. Refer to Figure B.1 and corresponding explanations. FIGURE B.1 - CONTROL PANEL 1. POWER SWITCH & LIGHT 1 2. TIG/STICK SWITCH 3. POLARITY SWITCH 4 4. CURRENT CONTROL 5. OVER TEMPERATURE LIGHT 6. REMOTE CONTROL CONNECTOR 7. ELECTRODE/ GAS OUTPUT RECEPTACLE 8. WORK CABLE & CLAMP 2 3 5 7 6 8 1. POWER SWITCH & LIGHT - Turns power on or CAUTION off to the welder
Summary of the content on the page No. 15
8 8 OPERATION 6. REMOTE CONTROL CONNECTOR - This connector REMOTE CONTROL OPERATION provides connection for a remote control. See Remote Control Operation in this section of the manual. A Foot Amptrol™ is included with the Square Wave TIG 175 for remote current control while TIG welding. An 7. ELECTRODE/GAS OUTPUT RECEPTACLE - This optional Hand Amptrol may also be used. An optional quick connect receptacle provides electrical connec- Arc Start Switch may be used to start and stop the tion to
Summary of the content on the page No. 16
9 9 OPERATION to weld through the complete range of 12 to 175 amperes in WARNING AC TIG or DC- TIG requiring only one electrode, a 3/32” 2% thoriated tungsten. In Stick Mode the output terminal and WELDING IN STICK MODE electrode will be electrically hot whenever the power switch is turned 1. Put the electrode holder and cable quick connect on. plug into the electrode output receptacle. Turn clock- wise until tight. Connect the work clamp to the work piece. 6. Adjust the Current Control to the
Summary of the content on the page No. 17
10 10 ACCESSORIES OPTIONAL ACCESSORIES TIG Torch Parts Kits - Parts kits are available for the K964-1 Undercarriage with Pivoting Single Gas LA-9 and LA-17 TIG torches. These kits include back Cylinder Platform - This undercarriage features a piv- cap, collets, collet bodies, nozzles and tungstens. oting platform to easily load and unload the gas cylin- Order KP507 for LA-9 torches der without lifting. It was designed specifically for the Order KP508 for LA-17 torches Square Wave TIG 175 power s
Summary of the content on the page No. 18
11 11 MAINTENANCE ommended. If the contacts are replaced reset the SAFETY PRECAUTIONS gap spacing to 0.015. Refer to figure C.1. Note in highly dirty environments where there is an abun- dance of conductive contaminants, use a low pres- sure air stream to clean the spark gap. Do not dis- WARNING turb the factory setting. ELECTRIC SHOCK can kill. 8. Inspect gas hose and inlet fitting for cracks or leaks. � Only qualified personnel should perform this maintenance. 9. Replace any unreadable lab
Summary of the content on the page No. 19
12 12 TROUBLESHOOTING HOW TO USE TROUBLESHOOTING GUIDE WARNING Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel. Unauthorized repairs performed on this equipment may result in danger to the technician and machine operator and will invalidate your factory warranty. For your safety and to avoid Electrical Shock, please observe all safety notes and precautions detailed throughout this manual. ________________________________________________________________
Summary of the content on the page No. 20
13 13 TROUBLESHOOTING Observe all Safety Guidelines detailed throughout this manual PROBLEMS POSSIBLE AREAS OF RECOMMENDED (SYMPTOMS) MISADJUSTMENTS(S) COURSE OF ACTION OUTPUT PROBLEMS Machine is Dead - 1. Make certain that the input No Output - No Fan power switch is in the “ON” position and machine is plugged in. 2. Check the input voltage at the machine. Input voltage must match the rating plate and voltage connection. Refer to Reconnect Procedure in the Installation sec- tion of this man
