Summary of the content on the page No. 1
CAPPUCCINO, COFFEE, and SOUP DISPENSERS
GB POUROVER models:
•GB1P
•GB2P
•GB3P
•GB4P
OPERATION MANUAL
• Specifications 2
• Installation and Operating Instructions 3
Adjustments 4
•
Test & Troubleshooting 8
•
Maintenance 9
•
Cleaning and Sanitizing 10
•
Parts Identification & Illustration 11
•
Wiring Diagrams 14
•
Cecilware sells value... Worldwide
45 -05 20th Avenue, Long Island City, NY 11105
Summary of the content on the page No. 2
Electrical Specifications Number of Receptacle Circuit Model No. Volts Phase Hz Watts Heaters Amps Nema No. Breaker GB1P, GB2P, GB3P 120V 1 60 1.8KW 1 15 5-15R 15A GB4P GB1P, GB2P, GB3P, 120/240V 1 50/60 3.0KW 1 15 L14-20R** 20A GB4P or 240V 50/60 3.0KW 15 L6-20R 20A 120V, 1.8 KW, 15A, Nema 5-15R standard on all models; 3.0 KW, 120/240V units available ** 120/240V, 3 pole, 4 wire grounding type Twist-Plug Receptacle. For 240V units, Use L6-20R, 2 pole, 3 Wire Twist-P
Summary of the content on the page No. 3
START UP INSTRUCTIONS FOR GB POUROVER CAPPUCCINO DISPENSER (see illustration 9-3 for clarification) I. INSTALLATION INSTRUCTIONS This equipment is to be installed to comply with the applicable Federal, State, or local plumbing codes having jurisdiction. In addition: 1. A quick disconnect water connection or enough extra coiled tubing (at least 2x the depth of the unit) so that the machine can be moved for cleaning underneath. 2. An approved back flow prevention device, such as a
Summary of the content on the page No. 4
III. PRIMING - AUTOFILL - Water Selection Switch - Toggle Down (See Back Panel) 1. Plug into power outlet. 2. Turn Heater Switch ON. 3. Allow 10 to 15 minutes for water to reach dispense temperature of 185°F. Heater Indicator Light (red) goes ON when heater is on (see lower front panel). 4. Fill hopper with product. 5. Place cup under dispenser. 6. Push and hold Dispense Button (green) until water flow s from mixing chamber 7. Machine is primed and ready to go.
Summary of the content on the page No. 5
HOPPER COVER CD106 AUGER GEAR – FOR RECTANGULAR HOPPERS: CD117 [Used With Nylon Auger CD130] CD117 [Used With Wire Auger CD101 &CD130] FRONT BUSHING: Rectangular Hoppers: CD277 [ Ø22.5 mm ] CD306 [ Ø17 mm ] Square Hoppers: CD102 [ Ø22.5 mm w/O-Ring CD103] CD131 [ Ø22.5 mm w/O Ring] AUGERS: 5 mm X 17mm Pitch w/O-Ring CD139] CD130 Nylon Auger [Ø22. CD101 Wire Auger [Ø22.5 mm X 17mm Pitch] Used for Cappuccino Fast Flow & Soup. PRODUCT GUIDE: CD70A White, CD272
Summary of the content on the page No. 6
DRINK SIZE ADJUSTMENTS (OPTIONAL FEATURE) a. Manual Dispense Machines: Hold down the Dispense Button until desired amount is dispensed. b. Automatic Machines with Programmable "Teach me" Timers [L576A or L582A]: The timer is programmable from the dispense button. Programming For Automatic Dispense 1. Turn Power Switch ON (toggle switch inside door). 2. Press and Hold [red] Stop Button with one hand. 3. Press and Hold [green] Dispense Button with other hand.
Summary of the content on the page No. 7
TEST A) Water Inlet Valve Test Turn power off. If the water level rises inside the tank, the Water Inlet Valve Check Valve Check Valve Check Valve is leaking. Disconnect wires from the Water Inlet Valve coil and connect a 2 wire Ass’y L463A Ass’y L463A Ass’y L463A line cord to the terminals. Plug it into a 115V outlet. If water flows in and stops when you pull it out, the Valve is working fine. Repeat this test a few times. The Hose Nut Ass’y K491A problem may be in the
Summary of the content on the page No. 8
TROUBLESHOOTING GUIDE FOR GB-POUROVER WARNING: To reduce the risk of electrical shock unplug the dispenser power cord before repairing or replacing any internal components of the unit.. Before any attempt to replace a component be sure to check all electrical connections for proper contact. PROBLEM PROBABLE CAUSE REMEDY 1 A Dispensing unit unplugged Reconnect dispensing unit Light Display B No power from Terminal Block Check the Terminal Block for loose wire not lit. C Defective B
Summary of the content on the page No. 9
MAINTENANCE To Replace The Picture / Duratran GB w/ Metal Doors Only: Lift up the two end tabs on top of door with a pointed object or flat head screwdriver. Pull the entire picture frame out. Open up the two clear panels and replace picture. Tuck clear plastic panel inside bracket at top. Be sure to tuck clear panel under bracket before sliding frame ass'y inside door. The longer metal tab side goes in the front. DURATRAN FRAME ASS'Y To Replace The Fluorescent Bulb: DURATR
Summary of the content on the page No. 10
CLEANING AND SANITIZING Sanitizing: All sanitizing agents in the food zone must comply with 21 CFR 178.1010. All food dispensing units should be sanitized periodically. All parts to be sanitized must be cleaned first. To prepare a sanitizing solution: Add 2 Tsp. Of Liquid Clorox Bleach (5.25% Concentration) To 1 gallon Of Water At Room Temperature (70°- 90°F). Note: Always start with a unopened bottle of Clorox Bleach since the solution from an opened bottle has a short life span
Summary of the content on the page No. 11
RESERVOIR AND TANK ASSEMBLY 1 2 Q174Q RESERVOIR ASSEMBLY ITEM P/N QTY DESCRIPTION 1. Q174A 1 P.O.-LINE TANK(GB3M/ICAP) 2. L499P 1 FLOAT SWITCH 70-V-A 3 3. M461A 3 DIRECT MOUNTING SEAL (.466 ID) 4. K402A 1 LEVEL CONTROL, 4 5. P410A 1 PROBE SEAL 6. K535A 1 LEVEL CONTROL PROBE 5 7. K525A 1 ELBOW ASS'Y-1/2" OD S.S. 90° 8. RI71A 1 UPPER TANK MOUNT BRACKET 6 7 8 9 HOT WATER TANK ASSEMBLY ITEM P/N QTY DESCRIPTION 10 9 P446A 4
Summary of the content on the page No. 12
DESCRIPTION AND LOCATION OF COMPONENTS (GB3P SHOWN) 62 61 60 1 59 2 58 3 57 56 55 4 54 53 5 6 52 7 8 51 50 9 49 48 47 46 10 45 11 44 12 43 13 42 14 41 15 CCW 16 40 CCW 17 39 CCW 18 38 37 19 20 21 23 25 26 28 29 30 31 32 33 34 35 36 22 24 27 12
Summary of the content on the page No. 13
ITEM DESCRIPTION GB1P GB2P GB3P 1 WATER BOTTLE 3 gal / OR 6 gal M518A / M519A M518A / M519A M518A / M519A 2 RESERVOIR /COVER 97128 97128 97128 3 RESERVOIR ASSY Q174Q Q174Q Q174Q 4 SILICONE HOSE - RESERVOIR TO TANK M540A M540A M540A 5 SILICONE HOSE - BREATHER TUBE TO BREATHER TUBE M541A M541A M541A 6 SILICONE HOSE - HOSE BARB TO RESERVOIR M542A M
Summary of the content on the page No. 14
DOOR UNIT N MAIN UNIT N N N N L1 N L1 N N L1 N N L1 N L1 14
Summary of the content on the page No. 15
DOOR UNIT N + + MAIN UNIT N N N N L1 N L1 N N L1 N N L1 N L1 15
Summary of the content on the page No. 16
DOOR UNIT N N N N N L1 N L1 N N L1 N N L1 N L1 16
Summary of the content on the page No. 17
DOOR UNIT N + + + MAIN UNIT N N N N L1 N L1 N N L1 N N L1 N L1 17
Summary of the content on the page No. 18
DOOR UNIT N + + MAIN UNIT N N N N L1 N L1 N N L1 N N L1 N L1 18
