Summary of the content on the page No. 1
KOBE Brand Range Hood
Model No. RA3830S
RA3836S
RA-038 SERIES – 5” HEIGHT
INSTALLATION INSTRUCTIONS
AND OPERATION MANUAL
Summary of the content on the page No. 2
- READ AND SAVE THESE INSTRUCTIONS - CONTENTS Important Safety Instructions………………………………………………………………. 1 Components of Packages………………………………………………………………….. 3 Installation…………………………………………………………………………………… 4 Under the Cabinet Installation………………………………..……..…………………. 5 Stand Alone Installation…………………………………………..……..……………… 8 Operating Instructions…………………………………...…………………………………. 11 Maintenance…………………………………………………………………………………. 12 Specifications…………………………………………………….……..……
Summary of the content on the page No. 3
IMPORTANT SAFETY INSTRUCTIONS - PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION - WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, OBSERVE THE FOLLOWING: 1) Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction. 2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities. 3)
Summary of the content on the page No. 4
What to Do In The Event Of a Range Top Grease Fire - SMOTHER FLAMES with a close fitting lid, cookie sheet, or metal tray, and then turn off the burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911. - NEVER PICK UP A BURNING PAN – You may get burned. - DO NOT USE WATER, including wet dishcloths or towels – a violent steam blast will result. - Use an extinguisher ONLY if:
Summary of the content on the page No. 5
COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) Range Hood Box Duct Cover Box (Sold Separately) {A} KOBE Range Hood {F} KOBE Duct Cover (Model No. RA1020DC) {B} Warranty Registration Card {G} Screws Package {C} Instructions Manual {H} Duct Cover-Mounting Bracket {D} Oil Containers (Round) {I} Hood-Mounting Bracket {E} Oil Containers (Oval) {A} {F} {B}
Summary of the content on the page No. 6
INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation Calculate the length of the installation, before installing the hood. (All calculation is measure in inches). - FOR UNDER THE CABINET - TABLE 1 A = Height of Floor to Ceiling B = Height of Floor to Counter Top (Standard: 36”) C = Preferred Height of Counter Top to Hood Bottom (Recommended 27” to 30”) D
Summary of the content on the page No. 7
UNDER THE CABINET INSTALLATION SAFETY W ARNING HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING, OR SERVICING. Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. - Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. - A straight, short venting run will allow the hood to perform more efficiently.
Summary of the content on the page No. 8
Figure 3 2. NOTE: Be careful when using electrical screwdriver, damage on the hood may occur. Unscrew the six screws on the bottom casing. Remove the bottom casing as shown in Figure 4. If necessary, arrange the electrical wire to run through the 1” diameter hole on the hood. 3. Using references on Table 1 and measurements on page 15, center the hood in place beneath the cabinet and flush with the front of
Summary of the content on the page No. 9
7. Connect the electrical wires. - If necessary to hide the electrical wire connections, push wires back into the wiring box. Access the wire connections underneath the hood by removing the bottom casing from the six screws. Before reattaching the bottom casing, make sure wires do not slip between motors, impellers, or any moving parts to prevent any damage. Connect three wires (black, white and green) to house wires and cap with wire connectors. - Connect according to color: black
Summary of the content on the page No. 10
STAND ALONE INSTALLATION ***This installation only applied with the purchase of a duct cover. SAFETY W ARNING HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR SERVICING. Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. - Decide the location of the venting pipe from the hood to the outside. Refer to Figure 8. - A straight, sh
Summary of the content on the page No. 11
4. Using references on Table 2 and measurements on page 15, decide the leveling point of the hood. Position two mounting screws (not provided) on the wall, leaving 1/8” away from the wall as shown in Figure 11. 5. Align hood-mounting bracket to the two screws on the wall and hook hood into place. Tighten screws to secure hood to the wall. CAUTION: MAKE SURE THE HOOD IS SECURE BEFORE RELEASING. Hood- Mounting Mounting Screws Bracket
Summary of the content on the page No. 12
Attach Together Figure 14 Wiring to Power Supply SAFETY W ARNING RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. - Connect three wires (black, white and green) to house w
Summary of the content on the page No. 13
OPERATING INSTRUCTIONS This KOBE hood is equipped with three-switch controls, two powerful centrifugal turbine impellers with safety screens, two bright 12-volt 20-watt halogen lights, and four oil containers. The three control switches are Light Control, Speed Control, and the Power Control (On/Off). Refer to Figure 17. Figure 17 Light Control
Summary of the content on the page No. 14
MAINTENANCE CAUTION: NEVER PUT YOUR HAND INTO THE AREA HOUSING THE FAN WHILE THE FAN IS OPERATING. For the optimal level of operation, clean the range hood surface, safety screens, and oil containers regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. *** Regular care will help preserve its fine appearance. 1) Use only mild soap or detergent solutions. Dry surfaces using soft cloth. 2) If hood looks splotchy (stainless steel h
Summary of the content on the page No. 15
To Replace Light Bulb CAUTION: HALOGEN LIGHT UNIT MAY BE HOT! WAIT UNTIL UNIT IS COOL. 1) Make sure all control switches are off, and range hood is unplugged. 2) Use a flat head screwdriver to pop out the protective covering as shown in Figure 18. 3) Gently pull out the defective light bulb and discard. Light bulbs should be 12V 20W maximum. Refer to Figure 19. Push bulb securely into light socket. 4) Replace protective cover. 5) Plug in range hood.
Summary of the content on the page No. 16
SPECIFICATIONS MODEL / SIZE RA3830S / 30” RA3836S / 36” COLOR # 430 Commercial Grade Stainless Steel VOLTAGE 120V 60Hz NUMBER OF MOTORS 2 DESIGN 18-Gauge Seamless FAN TYPE Twin Turbine Impeller EXHAUST 6” Round CONTROLS Two Speed (Low & High) HALOGEN LIGHTS 12V 20W x 2 HOOD DIMENSION (RA3830S) 29-3/4” x 20-1/2” x 5-1/8” (W x D x H) (RA3836S) 35-1/4” x 20-1/2” x 5-1/8” OPTIONAL ACCESSORIES 1) Two-Piece Adjustable Duct Cover (W x D x H) (RA1020DC) 10-5/8” x 9-1/8”
Summary of the content on the page No. 17
MEASUREMENTS & DIAGRAMS ***All inch measurements are converted from millimeter. Inch measurements are estimated. ***All measurements in ( ) are millimeters. -FOR UNDER THE CABINET- 30” = Knockout Holes “A” 36” = Knockout Holes “A” & “B” -FOR STAND ALONE (WITH OPTIONAL DUCT COVER)- ***Hood-Mounting Bracket ***Duct Cover-Mounting Bracket
Summary of the content on the page No. 18
PARTS LIST MODEL NO.: RA3830S RA3836S NO. DESCRIPTION MODEL /SIZE PART NO. 1 6” Round Plastic Exhaust C1-0505-0001 2 Capacitor C1-0401-0120-01A 3 Transformer (Motor) C1-0402-0120-40 4 Screw (4 x 6 mm) C1-0708-0001 5 Screw (4 x 6 mm) C1-0708-0001 6 Power Cord C1-0406-0120 7 Screw (TS 4 x 18 mm) C1-0708-0004 8 Plastic Plate C1-0507-0201 9 Hood Casing RA3830S 10-03300 RA3836S 10-03360 10 Screw (3/16” x 5/8”) C1-0704-0004 11 Halogen Light (12V 20W M
Summary of the content on the page No. 19
MODEL NO.: RA3830S RA3836S 17
Summary of the content on the page No. 20
CIRCUIT DIAGRAM MODEL NO.: RA3830S RA3836S KEY CODE W = White BK = Black = Brown BR R = Red GR = Green Y = Yellow G = Grey B = Blue 18
