Summary of the content on the page No. 1
Installation Instructions and
Use and Care Guide
30" (76.2 cm)
36" (91.4 cm)
42" (106.7 cm)
48" (121.9 cm)
Wall-Mount
™
Pro Line Range Hood
Quick Reference
IMPORTANT:
Table of Contents:
Read and save
Pages
2
Before you start
these instructions.
3 Product dimensions
3
Cabinet dimensions
3 Venting requirements
IMPORTANT:
5
Electrical requirements
Installer: Leave Installation Instructions with
the homeowner.
5 - 7
Installation steps
Homeowner: Keep Installation Instructions for
8
Use and Care I
Summary of the content on the page No. 2
Parts needed: WARNING — TO REDUCE THE Before you start... RISK OF FIRE, ELECTRIC • 2 U.L.- or C.S.A.- listed, 1/2" (12.5 mm) SHOCK, OR INJURY TO conduit connectors PERSONS, OBSERVE THE • power supply cable Your safety and the safety of FOLLOWING: • 1 wall or roof cap others is very important. Installation work and electrical • metal vent system We have provided many important wiring must be done by qualified safety messages in this manual and person(s) in accordance with all on your appliance.
Summary of the content on the page No. 3
Product dimensions Cabinet dimensions 12-1/32" (30.6 cm) vent cover (if used) 12" (30.5 cm) 30" (76.2 cm) hood: 30" (76.2 cm) 36" (91.4 cm) hood: 36" (91.4 cm) 42" (106.7 cm) hood: 42" (106.7 cm) 2-7/32" 48" (121.9 cm) hood: 48" (121.9 cm) (5.6 cm) min. cabinet opening widths 18-3/16" (46.2 cm) canopy 1-3/8" (3.5 cm) 13" (33 cm) cabinet depth 25-3/16" 30" (76.2 cm) hood: 29-7/8" (75.9 cm) 18" (45.7 cm) 30" (76.2 cm) min. bottom of (64 cm) 36" (91.4 cm) hood: 35-7/8" (91.1 cm) min. canop
Summary of the content on the page No. 4
Horizontal venting Vertical venting Venting methods This canopy range hood is factory set for roof cap vertical venting. For rear vent applications, the blower must be turned inside the range hood so 3-1/4" x 10" (8.3 cm x 25.4 cm) that the blower vents to the rear as indicated. vertical venting The blower is turned by removing two screws (roof or wall) 3-1/4" x 10" on each side of the blower, rotating the blower (8.3 cm x 25.4 cm) horizontal venting with the exhaust opening facing the rear and
Summary of the content on the page No. 5
Electrical requirements (COPPER WIRE ONLY) and separate 15-amp circuit, fused on Important: Observe all governing connections must conform with the both sides of the line. codes and ordinances. rating of the appliance as specified Do not ground to a gas pipe. It is the customer’s responsibility: on the model/serial rating plate. Check with a qualified electrician if •To contact a qualified electrical Wire sizes must conform to the you are not sure range hood is installer. requirements of the Nat
Summary of the content on the page No. 6
Vent and Electrical openings 2-7/8" (7.5 cm) 2-7/8" C L (7.5 cm) All vent openings are 3-1/4" x 10" (8.3 cm x 25.4 cm) 1-1/8" 2-7/8" (2.9 cm) (7.5 cm) 2-7/8" (7.5 cm) 9-11/16" Electrical (24.6 cm) opening 6-3/32" (15.5 cm) 30" (76.2 cm) hood 36" (91.4 cm) hood 6-3/32" 42" (106.7 cm) hood (15.5 cm) Electrical opening C L 48" (121.9 cm) hood 10-1/2" (26.7 cm) top of hood 5.The hood attaches to the wall 5a. Optional vent cover 18-9/16" 18-9/16" with the mounting screws located installation: Attach
Summary of the content on the page No. 7
5b. If chimney extension is 12. The brackets are also used WARNING used: Attach the extension brackets to adjust the level of the canopy. Excessive Weight Hazard as shown. Using a Phillips screwdriver, rotate the screw V2 to adjust the level of Use two or more people to move ceiling 10-5/8" the canopy. (27 cm) and install range hood. Failure to do so can result in back or other injury. 13. Connect vent system to brackets hood. Seal all joints with duct tape. 9. If roof or wall cap does not 14. I
Summary of the content on the page No. 8
16. Install the filters. 18. The canopy hood If range hood does not operate: controls are located on the right- • Remove the filters from the box Check that the circuit breaker hand underside of the canopy. and remove the white protective is not tripped or the house coating from the filters. fuse blown. Note: Use two hands to install Disconnect power supply. controls filter, one to pull and turn the Check that wiring is correct. knob, the other to hold the filter in place so that it doesn’
Summary of the content on the page No. 9
Opening the canopy hood Replacing the Halogen Cleaning lamps: control panel: Filters: 36" (91.4 cm) and 42" (106.7 cm) hoods The hood controls are located on shown. The filters should be washed the right-hand underside of the frequently. Place metal filters in canopy. dishwasher or hot detergent solution to clean. controls To remove filters: Note: Use two hands to remove filters, one to pull and turn the knob, the other to hold the filter so that it doesn’t fall onto the cooktop. • Pull knob f
Summary of the content on the page No. 10
Wiring diagrams For 30" (76.2 cm), 36" (91.4 cm) For 48" (121.9 cm) hoods and 42" (106.7 cm) hoods Warranty ® KitchenAid Range Hood Warranty LENGTH OF WARRANTY KitchenAid WILL PAY FOR LIMITED ONE-YEAR WARRANTY Labor and any parts of your range hood (except light bulbs and From Date of Purchase filters) which are defective in materials or workmanship. KitchenAid WILL NOT PAY FOR A. Consumable parts such as light bulbs and filters. B. Service calls to: 1. Correct the installation of the range hood
Summary of the content on the page No. 11
Requesting Assistance or Service To avoid unnecessary service calls, please check the “Check Operation” section. It may save you the cost of a service call. If you still need help, follow the instructions below. If you need assistance or service in U.S.A. Call the KitchenAid Customer Interaction Use and maintenance procedures • Center toll-free at 1-800-235-0665. Accessory and repair parts sales • Our consultants are available to assist you. Specialized customer assistance (Spanish • When callin
Summary of the content on the page No. 12
Requesting Assistance or Service Before calling for assistance or service, please check the “Check Operation” section. It may save you the cost of a service call. If you still need help, follow the instructions below. If you need assistance or service in Canada ✝ 2. If you need service ... 1. If the problem is not due to one of the items ✝ Contact your nearest KitchenAid Canada Appli- listed in “Check Operation” ... ance Service branch or authorized servicing Contact the dealer from whom you ou
Summary of the content on the page No. 13
Instructions d’installation et Guide d’utilisation et d’entretien Hotte d’aspiration pour cuisinière ™ Pro Line - montage mural 76,2 cm (30 po) 91,4 cm (36 po) 106,7 cm (42 po) 121,9 cm (48 po) Référence rapide IMPORTANT: Table des matières : Lire et conserver Pages 2 Avant de commencer... ces instructions. 3 Dimensions du produit 3 Dimensions des placards 3 Circuit de décharge de l’air IMPORTANT: 5 Alimentation électrique Installateur : Remettre les instructions d’installation au propriétaire
Summary of the content on the page No. 14
tiennent compte des dégagements de Pièces fournies : séparation nécessaires. Avant Vis de montage: d’effectuer un découpage, consulter Avant de 76,2 cm (30 po) = 2 Plaquettes d'obturation les instructions d’installation fournies 91,4 cm (36 po) = 2 (orifices de sortie) : par le fabricant de la cuisinière ou commencer. . . 106,7 cm (42 po) = 4 76,2 cm (30 po) = 1 table de cuisson. 121,9 cm (48 po) = 4 91,4 cm (36 po) = 1 Une prise de courant électrique reliée 106,7 cm (42 po) = 1 121,9 cm (48 po
Summary of the content on the page No. 15
Dimensions du produit Dimensions des placards 30,6 cm (12 1/32 po) 30,5 cm garniture (12 po) cache-conduit (option) 5,6 cm hotte 76,2 cm (30 po) : 76,2 cm (30 po) (2 7/32 po) 46,2 cm hotte 91,4 cm (36 po) : 91,4 cm (36 po) (18 3/16 po) hotte 106,7 cm (42 po) : 106,7 cm (42 po) hotte 121,9 cm (48 po) : 121,9 cm (48 po) distance libre min. entre les placards 3,5 cm hotte (1 3/8 po) hotte 76,2 cm (30 po) : 64 cm 75,9 cm (29 7/8 po) (25 3/16 po) profondeur distance min. entre hotte 91,4 cm (36
Summary of the content on the page No. 16
Configurations de Décharge à travers le toit Décharge horizontale à travers le mur circuit de décharge bouche de décharge La hotte d’aspiration est configurée à l’usine pour la décharge à travers le toit ou un mur. Pour conduit de 8,3 x 25 cm l’évacuation par l’arrière, il faut modifier l’orientation (3 1/4 x 10 po) - du ventilateur à l’intérieur de la hotte pour que le décharge à conduit de ventilateur rejette l’air par l’arrière. Pour cela, ôter les travers le toit 8,3 x 25 cm (3 1/4 x 10
Summary of the content on the page No. 17
Alimentation électrique Important : Respecter les prescriptions chaque conducteur. d’alimentation. Le calibre des de tous les codes et règlements en conducteurs (CUIVRE SEULEMENT) et Ne pas utiliser une tuyauterie de gaz vigueur. les pièces de connexion doivent être pour la liaison à la terre. compatibles avec la demande de C’est au client qu’incombe la En cas d’incertitude quant à la qualité courant de l’appareil spécifiée sur la responsabilité de : de la liaison à la terre de la hotte, plaque
Summary of the content on the page No. 18
• Déterminer la hauteur d’installation Ouvertures pour conduit d’évacuation et câble électrique de la hotte. 7,5 cm • Positionner la hotte contre le mur en 2-7/8" (2 7/8 po) (7.5 cm) faisant coïncider le bord inférieur de 7,5 cm 2-7/8" C L la hotte avec le sommet du dosseret. (7.5 cm) (2 7/8 po) All vent openings are Dimensions des ouvertures Marquer la position des quatre trous 3-1/4" x 10" (8.3 cm x 25.4 cm) 2,9 cm de décharge 8,3 x 25,4 cm 7,5 cm 1-1/8" 2-7/8 des angles. On recommande q
Summary of the content on the page No. 19
Raccordement au 7. Déterminer la hauteur appropriée tringle mur pour l’orifice de passage du câble réseau électrique d’alimentation; percer un trou de 32 mm (1 1/4 po) à cet endroit. Faire passer le câble à travers le trou selon V1 les prescriptions du Code national des AVERTISSEMENT installations électriques ou de la V2 norme CSA, ou des codes ou règlements locaux en vigueur. La longueur du câble devra être vis de suffisante pour qu’il soit possible de hotte montage réaliser les connexions adéq
Summary of the content on the page No. 20
vitesse), puis à la position « 2 » Contrôle du 16. Installer les filtres. (vitesse moyenne), puis à la position « 3 » (haute vitesse). • Sortir les filtres de la boîte et enlever fonctionnement la pellicule de protection blanche des Placer les commutateurs filtres. d’éclairage et du ventilateur à la 17. Mettre la hotte sous tension. position « 0 » pour commander Note : Lors de l’installation du filtre, l’arrêt du ventilateur et l’extinction tirer/faire tourner le bouton avec une de la lampe.
