Summary of the content on the page No. 1
Summary of the content on the page No. 2
Contents Preface .........................................................................................2 Installation....................................................................................4 Unpacking............................................................................................................................................................................... 4 Adjust height and angle of Tilt stand..........................................................
Summary of the content on the page No. 3
Preface This manual is designed to assist users in setting up and using the LCD Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form
Summary of the content on the page No. 4
Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean the LCD Monitor screen: -- Power off the LCD Monitor and unplug the AC Cord. -- Spray a non-solvent cleaning solution onto a rag. -- Gently clean the screen with dampened rag. 2. Do not place the LCD Monitor near a window. Exposing the monitor to rain water, moisture or sunlight can severely damage it. 3. Do not apply pressure to the LCD
Summary of the content on the page No. 5
Installation Unpacking Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot. After you unpack the LCD Monitor, make sure that the following items were included in the box: *
Summary of the content on the page No. 6
o Adjust height and angle of Tilt stand 40 The monitor screen may be raised or lowered and tilted (-5 to 40 degree). To raise or lower the monitor screen, place hands on each side of the monitor screen and lift or lower to the desired height as shown in the right figure. o 5 o 170 o 170 Figure 1-1 CAUTION: * When lowering the monitor screen avoid catching your hand and o o 40 -5 fingers between the monitor screen and the tilt stand base. o -5 o *The monitor screen can be tilted b
Summary of the content on the page No. 7
Connecting the AC Power 1. Connect the power cord to the LCD Monitor.(See Fig. 1-4) 2. Connect the power cord to an AC power source. 3. Turn the AC power switch to On. AC Power switch AC Power Jack Power Cord Figure 1-4 Connecting the USB Hub 1. Connect the “A“ end of the USB cable to your computer. 2. Connect the “B “end of the USB cable to the USB hub on the monitor. 3. Connect USB compliant products directly to the USB hub on the monitor. ( See Fig 1-5) Figure 1-5
Summary of the content on the page No. 8
Display Controls User Controls A brief description and the location of all LCD Monitor functions controls and indicators Figure 2-1 Push to turn ON or turn Off. 1 Activates OSD main menu. MENU 2 Exit OSD display / DV mode hot key. EXIT 3 Select DVI or D-SUB signal source. (Toggle Switch) SOURCE 4 Hot key for manually auto adjusting the display. AUTO 5 Green when the monitor is on, Amber when in power saving mode, and Dark when off. LED 6 A four direction key plus en
Summary of the content on the page No. 9
Adjusting the Monitor's Display The monitor has four function control buttons to select among functions shown on OSD menu, designed for easy user-viewing environments. OSD Function Menu To activate the OSD Main menu, simply press ”Menu” button , the menu diagram will pop up on the screen as shown on Fig. 2-2 Use the 4D+1 key to navigate through the function you want to adjust. Push the 4D+1 key to enter a sub-menu and adjust the value. Push the 4D+1 key again to exit the sub-menu.
Summary of the content on the page No. 10
Function Description Figure Function Function Description The following DV mode display setting can be selected by OSD DV MODE (STANDARD/TEXT/sRGB/MOVIE/GAMING/PHOTO) Default setting: TEXT Adjust the brightness. BRIGHTNESS Factory setting: 100.0% Adjust the image contrast. CONTRAST Factory setting:50.0% Adjust the sharpness. SHARPNESS Factory setting: 50% AUTO CONTRAST Adjust the CONTRAST to the optimal value for the (D-SUB or DVI-I video-input level automatically. Analog
Summary of the content on the page No. 11
Choose different color temperature (9300K, 7500K, sRGB, USER). Color Temperature Default is USER. USER mode adjustable. Adjust the contrast and brightness of each color of the white balance. RED GREEN Allows you to adjust the Red/Green/Blue color gain. BLUE GAIN RED GREEN Allows you to adjust the Red/Green/Blue color offset. BLUE OFFSET Adjust color depth, increasing this value makes pictures more colorful, decreasing makes pictures less colorful. SATURATION Adjustab
Summary of the content on the page No. 12
Provide information about resolution, H/V frequencies, Information and polarity of the input signal. This OSD informs the user the current signal that is displayed. Input Select This OSD will automatically turn off after 2 seconds or by pressing the “Exit” key. This OSD gives a warning when the selected input signal is not active. After power on or when the input signal become inactive, this warning appears. No signal OSD shall be shown after around 0.5sec from OSD Warnings v
Summary of the content on the page No. 13
This function gives warning about input resolution or refresh rate that the monitor cannot display. OSD Warnings If video signal is not at the proper timing when the OUT OF RANGE monitor powers on or input signal is changed, this message opens and it disappears after 45 seconds, or by "EXIT" key. When the monitor is displayed for the first time and the Auto Adjust resolution is 800x600 and above, the monitor will auto (Analog Input adjust itself. Only) To manually execute the
Summary of the content on the page No. 14
OSD Lock Out Function OSD Lock Function allows you to lock out the OSD menu and the button keys. To activates the OSD lock function, the monitor must be in a normal display mode and the information menu as shown in fig-2-4 must be activated. Then follow the instructions below. Figure 2-4 Option 1: OSD lock – all buttons be locked except the “POWER” button. Press “Exit Key + Menu Key + Soft power key” at same time The monitor will show an “OSD Lock Out” message, showing time a
Summary of the content on the page No. 15
Technical Information Specifications LCD Panel Size 26" Display Type Active matrix color TFT LCD Resolution 1920 x 1200 Display Dot 1920 x (RGB) x 1200 Display Area (mm) 550.08 x 343.8 (H x V) Display Color 16.7M (RGB 8 bit) Video Input Signal Analogue RGB ; Digital TMDS Input Impedance 75 Ohm ± 2% (VGA) Polarity Positive, Negative (VGA) Amplitude 0 - 0.7 ± 0.05 Vp (VGA) Multi-mode Supported Horizontal Frequency: 31 ~ 93.75kHz Vertical Frequency: 50 ~ 76 Hz Control Pow
Summary of the content on the page No. 16
Power Management Mode Power Consumption* AC Input LED Color DPM ON 135W maximum 240 VAC Green DPM OFF 2W maximum 240 VAC Amber DC switch off 1W maximum 240 VAC Dark Disconnected 2W maximum 240 VAC Dark Meeting VESA DPM requirements measured from AC Input end of AC power cord. Sync Input Analogue Signal Separate TTL compatible horizontal and vertical synchronization Polarity Positive and negative Plug & Play Supports VESA DDC2B functions External Connection Power Input (AC in
Summary of the content on the page No. 17
Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the most suitable available timing. FH (KHz) SYNC TOTAL ACTIVE SYNC FRONT BACK PIXEL FV (Hz) POLARITY (DOT / LINE) (DOT / LINE) WIDTH PORCH PORCH FOREQ.(MHz) TIMING NAME (DOT / LINE) (DOT / LINE) (DOT / LINE) 640x350 31.469 + 800 640 96 16 48 25.175 VGA-350 70.087 – 449 350 2 37 60 640x400 31.469 – 800 640 96 16 48 25.175 VGA-GRAPH 70.087 + 449 400 2 12 35 640x480 31.46
Summary of the content on the page No. 18
(75Hz) 75.06 – 915 870 3 3 39 1280x720 44.772 – 1664 1280 128 64 192 74.5 (60Hz) 59.855 + 748 720 5 3 20 1280x960 60 + 1800 1280 112 96 312 108 (60Hz) 60 + 1000 960 3 1 36 1280x960 70 + 1800 1280 112 96 312 126 (70Hz) 70 + 1000 960 3 1 36 1280x960 75 + 1800 1280 112 96 312 135 (75Hz) 75 + 1000 960 3 1 36 1280x1024 64 + 1688 1280 112 48 248 108 VESA-1024-60Hz 60 + 1066 1024 3 1 38 1280x1024 80 + 1688 1280 144 16 248 135 VESA-1024-75Hz 75 + 1066 1024 3 1 38 1360x768 75 + 1792
Summary of the content on the page No. 19
Troubleshooting This LCD Monitor has pre-adjusted using factory standard VGA timings. Due to the output timing differences among various VGA cards in the market, users may initially experience an unstable or unclear display whenever a new display mode or new VGA card is selected. Attention This LCD Monitor Supports Multiple VGA Modes. Refer to the Standard Timing Table for a listing of modes supported by this LCD Monitor. PROBLEM Picture is unclear and unstable The picture is u
Summary of the content on the page No. 20
Product Registration and Technical Support Register Your Planar Products Today Thank you choosing Planar. To assure you receive all the benefits of your Planar product and services, register your Planar product today. Visit our website to register your product at http://www.planar.com/support/product_registration.html Cables, Replacement Lamps, Accessories To find cables, replacement lamps and accessories for your Planar projector, LCD monitor, touch screen or other Planar products
