Summary of the content on the page No. 1
PT1500MX / PT1550MX /
PT1501MX / PT1575S / PT1585P
Touch Screen LCD Monitors
USER’S GUIDE
www.planartouch.com
Summary of the content on the page No. 2
Important Recycle Instructions: Lamp(s) inside this product contains mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG. For more information on how to recycle your product, please vis
Summary of the content on the page No. 3
1 Table of Contents Usage Notice ........................................................................... 3 Precautions .........................................................................................3 Introduction ............................................................................. 4 About PT1500MX / PT1550MX / PT1501MX / PT1575S / PT1585P..4 Touch Screen for PT1500MX / PT1550MX..................................4 Touch Screen for PT1501MX....................................
Summary of the content on the page No. 4
2 Appendix................................................................................20 Troubleshooting.................................................................................20 Warning Signal..................................................................................21 No Signal ....................................................................................21 Going to Sleep .............................................................................21 Out of Range ....
Summary of the content on the page No. 5
3 Usage Notice Warning- To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture. Warning- Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Do: Turn off the product before cleaning. Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass c
Summary of the content on the page No. 6
4 Introduction About PT1500MX / PT1550MX / PT1501MX / PT1575S / PT1585P The PT1500MX / PT1550MX / PT1501MX / PT1575S / PT1585P is a 15” flat panel screen with an active matrix, thin-film transistor (TFT) liquid crystal display (LCD). Features include: Direct Analog signal input Active matrix TFT LCD technology 1024x768 XGA resolution 15” viewable display area 31.47 ~ 60.02 kHz horizontal scan 56 ~ 75 Hz high refresh rate 0.297mm x 0.297mm pixel pitch Auto adjustment f
Summary of the content on the page No. 7
5 Touch Screen for PT1500MX / PT1550MX 5-wire resistive touch screen for finger and stylus input Surface: Anti-glare treatment Interface: Dual RS-232 Serial/USB controller Durability: 35 million touches at a single point Hardness of surface: 3H Typical Operating force: 40g~200g when using a silicon rubber tipped pen with a 1 mm diameter minimum and a hardness of 60 degree. Transmittance: 82%±5% ® Driver: Windows 7, VISTA, XP, 2000, ME, 98, NT4.0, CE, XP Embedded, ® Linux,
Summary of the content on the page No. 8
6 Touch Screen for PT1585P Project capacitive touch screen for finger input only Surface: Glare treatment Interface: USB controller Transmittance: 90%±5% ® Driver: Windows 7, VISTA 64/32 bits, XP, 2000, CE, XP Embedded ® Express, Linux, Apple Mac OS
Summary of the content on the page No. 9
User’s Manual 7 Package Overview LCD Display Power Cord VGA Signal Cable RS-232 Cable USB Cable (A to A) Audio-in Cable (PT1500MX / PT1550MX (PT1550MX) PT1501MX / PT1575S only) USB Cable (A to B) Touch Screen Driver User’s Guide Installation CD-ROM Landing Strip DC Power Supply Cable Cover (sold separately) Screw
Summary of the content on the page No. 10
8 Installation Product Overview ► Front View PT1500MX/PT1550MX PT1585P PT1501MX/PT1575S ► PT1500MX/PT1550MX/PT1501MX/PT1575S Bottom View (Without Stand) ► PT1585P Bottom View (Without Stand)
Summary of the content on the page No. 11
9 Start Your Installation 1. Lay the LCD flat on an even surface. 2. Remove the stand back cover by pulling in the direction of the arrow as seen in step 2 diagram. 3. Move the stand into position as seen in step 3 diagram. 4. Connect the cables to the appropriate connectors as seen in Step 4 diagram. Use step 4-1 diagram if using the RS-232 serial connector. Use step 4-2 diagram if using the USB connector.
Summary of the content on the page No. 12
10 5. Take the optional cable cover and screw from the accessory box. Position all cables under the cover lip as seen in the step 5 diagram. 6. Using a Philips Head screwdriver, insert the screw (CBM M3x6) into the cable cover and monitor as seen in the step 6 diagram. 7. Re-attach the stand back cover to the LCD stand by pressing firmly until the tabs snap into place as seen in the step 7 diagram. You may also keep the cables in order by using the cable organizer.
Summary of the content on the page No. 13
11 Connecting the Display (Figure 12.1) To setup this display, please refer to the following figure and procedures. 1. Be sure all equipment is turned off. 2. Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet (12.1). 3. Connect the D-SUB cable from the display’s VGA input connector to the D-SUB connector of your host computer and tighten the screws (12.1). 4. Connect the Audio-In cable from the audio input port of your display t
Summary of the content on the page No. 14
12 (Figure 12.1) ► PT1500MX/PT1550MX/PT1501MX/PT1575S ► PT1585P
Summary of the content on the page No. 15
13 Kensington Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products. The Kensington lock is not included.
Summary of the content on the page No. 16
14 VESA Mount your monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which defines a physical mounting interface for flat panel monitors, and corresponding with the standards of flat panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your monitor. To mount the monitor on a UL certified swing arm or other mounting fixture, follow the instructions included with the mounting fi
Summary of the content on the page No. 17
15 Remove the Deskstand 1. Remove stand back cover. 2. Remove hinge cover 3. Remove 4 screws and then remove hinge.
Summary of the content on the page No. 18
16 User Controls Side Panel Controls OSD Menu off status Menu on status Key Menu appear Menu disappear / return to main item Brightness Main item select up / Adjust up Mute Main item select down / Adjust down Enter / Select sub-item function Power On / Off
Summary of the content on the page No. 19
17 How to Use the OSD Menus 1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the six functions in the main menu. 2. Choose the adjustment items by pressing the “Enter ” button. 3. Adjust the value of the adjustment items by pressing the “Up” or “Down” button. 4. With the OSD menu on screen, press “ Menu” button to return main menu or exit OSD. 5. The OSD menu will automatically close, if you have left it idle for a pre-set tim
Summary of the content on the page No. 20
18 (c.) When the “UP” or “Down” button is released, the previous setting will be saved and exit the “Lock/Unlock” menu automatically. Please note: a. When the OSD Lock function is selected, this indicates that all the buttons except “power” button are now disabled. b. When the Power Lock function is selected, this indicates that the power key is disabled; user can not to turn off the monitor by “Power” key.
