Summary of the content on the page No. 1
Summary of the content on the page No. 2
Contents Preface .........................................................................................2 Installation ...................................................................................4 Unpacking.......................................................................................................................................................................................4 Package Overview .........................................................................
Summary of the content on the page No. 3
Preface This manual is designed to assist users in setting up and using the LCD Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form,
Summary of the content on the page No. 4
Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean LCD Monitor screen; -- Power off LCD Monitor and unplug the AC Cord. -- Spray a non-solvent cleaning solution onto a rag. -- Gently clean the screen with dampened rag. 2. Do not place the LCD Monitor near a window. Exposing the monitor to rain water, moisture or sunlight can severely damage it. 3. Do not apply pressure to the LCD scr
Summary of the content on the page No. 5
User’s Manual Installation Unpacking Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot. After you unpack the LCD Monitor, make sure that the following items were included in the b
Summary of the content on the page No. 6
Viewing Angle Adjustment +90° The LCD Monitor is designed to allow users to have a comfortable viewing angle. The viewing angle can be adjusted -2° from -2°to +90°.(See fig. 1-1) Figure 1-1 Warning Do not force the LCD Monitor over its maximum viewing angle settings as stated above. Attempting this will result in damaging the Monitor and Monitor stand. Detaching LCD Monitor from Its Stand Unscrew screws from the base support column and pull down the hinge to release. F
Summary of the content on the page No. 7
Connecting the AC Power 1. Connect the power cord to the LCD Monitor.(See Fig. 1-5) 2. Connect the power cord to an AC power source. Figure1-5 Connecting the Audio Cable 1. Connect the audio cable to the "LINE OUT" jack on your PC's audio card or to the front panel's “AUDIO OUT” jack of your CD ROM drive. (See Fig. 1-6) Connect the other end of the audio cable to the LCD Monitor's "LINE IN" jack. Figure1-6 Connecting the USB Cable 1. Connect the USB cable to y
Summary of the content on the page No. 8
Display Controls User Controls A brief description and the location of all LCD Monitor functions controls and indicators: Figure 2-1 Power LED will be Green when monitor is on, be yellow when in power saving 1 mode, be dark when monitor in off mode. Power ON/OFF switch. Push to power on or power off. (Toggle switch) 2 Shows main OSD menu/ Enter key (in OSD menu)/ Audio mute and unmute 3 Menu/Enter ( must activate Volume OSD first, push ▲ / ▶ then Menu/Enter) Shows Volume
Summary of the content on the page No. 9
Adjusting the Monitor's Display Main OSD Sub Main Menu icon Sub Menu item Description Menu item STANDARD Default Setting. Reflects native display capability. Displays scenes in clearest detail. Pictures and MOVIE photographs appear in vibrant colors with sharp detail. Preset Mode GAME Enhances color. Optimal balance of brightness and contrast TEXT prevent eyestrain. The most comfortable way to read onscreen text PHOTO Enhances colors and emphasize fine detail. Adjusts
Summary of the content on the page No. 10
FULL Selects wide format for display. Expansion Mode ASPECT Selects 4:3 format for display. Auto adjusts the H/V Position, Phase and Clock of Auto Adjustment picture. (available in analog mode only) Adjusts the horizontal position. H. Position (available in analog mode only) Adjusts the vertical position. V. Position (available in analog mode only) Adjusts picture Clock. Clock (available in analog mode only) Adjusts picture Focus. Phase (available in analog mode o
Summary of the content on the page No. 11
Shows the resolution, H/V frequency and input port Information of current input timing. Icon Function Description CIE coordinated Color Temperature of 9300°K Sets the CIE coordinate color temperature to 9300°K 9300 CIE coordinated Color Temperature of 7500°K Sets the CIE coordinate color temperature to 7500°K 7500 CIE coordinated Color Temperature of 6500°K Sets the CIE coordinate color temperature to 5000°K 5000 Three colors (Red, Green, Blue) can be Sets the settings to a by u
Summary of the content on the page No. 12
OSD Lock Out Function When monitor is in normal display, you can enable the “OSD LOCK OUT” function. Option 1: OSD & Power button lock-all 5 buttons including the “POWER” button are locked. Press and hold the “Auto/Exit” and “ ”buttons at the same time for 3 seconds to lock all 5 buttons The monitor will show an “OSD LOCKED !” message for 5 seconds and the message will disappear automatically. OSD LOCKED Repeat this step to unlock. Option 2: OSD Lock – al
Summary of the content on the page No. 13
Technical Information Specifications LCD Panel Size 19W" Display Type Active matrix color TFT LCD Resolution 1440 x 900 Display Dot 1440x (RGB) x 900 Display Color 16.7M with FRC or Dithering Video Input Signal Analog RGB 0.7Vp-p Input Impedance 75 Ohm ± 2% Polarity Positive, Negative Amplitude 0 - 0.7 ± 0.05 Vp Horizontal Frequency: 30 ~ 80 kHz 30~80kHz Multi-mode Supported Vertical Frequency: 56 ~ 75 Hz 56~75Hz Control Power switch (hard and soft types) On/Off swit
Summary of the content on the page No. 14
Power Management Mode Power Consumption* AC Input LED Color DPM On 42 W maximum 240 VAC Green DPM Off 2 W maximum 240 VAC Yellow DC switch off 1 W maximum 240 VAC Dark *Meeting VESA DPM requirements measured from AC Input end of AC power cord. Sync Input Analog Separate TTL compatible horizontal and vertical TMDS Signal synchronization. -- Polarity Positive and negative Plug & Play Supports VESA DDC2B DDC/CI functions External Connection Power Input (AC input) A
Summary of the content on the page No. 15
Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the most suitable available timing. SYNC FRONT BACK FH (KHz) SYNC TOTAL/ ACTIVE PIXEL TIMING NAME WIDTH PORCH PORCH FV (Hz) POLARITY (DOT / LINE) FOREQ.(MHz) (DOT / LINE) 640x350 31.469 + 800 640 96 16 48 25.175 VGA-350 70.087 – 449 350 2 37 60 640x400 31.469 – 800 640 96 16 48 25.175 VGA-GRAPH 70.087 + 449 400 2 12 35 640x480 31.469 – 800 640 96 16 48 25.175 VGA-480 59.94 – 52
Summary of the content on the page No. 16
SYNC FRONT BACK FH (KHz) SYNC TOTAL/ ACTIVE PIXEL WIDTH PORCH PORCH TIMING NAME FV (Hz) POLARITY (DOT / LINE) FOREQ.(MHz) (DOT / LINE) 1024x768 60.023 + 1312 1024 96 16 176 78.75 VESA-768-75Hz 75.029 + 800 768 3 1 28 1024x768 60.24 – 1328 1024 96 32 176 80 1152x864 54.054 + 1480 1152 96 40 192 80 (60Hz) 59.27 + 912 864 3 13 32 1152x864 63.851 + 1480 1152 96 32 200 94.499 (70Hz) 70.012 + 912 864 3 1 44 1152x864 67.5 + 1600 1152 128 64 256 108 (75Hz) 75 + 900 864 2 2 32 1152
Summary of the content on the page No. 17
Troubleshooting This LCD Monitor has been pre-adjusted using factory standard VGA timings. Due to the output timing differences among various VGA cards in the market, users may initially experience an unstable or unclear display whenever a new display mode or new VGA card is selected. Attention This LCD Monitor Supports Multiple VGA Modes. Refer to the Standard Timing Table for a listing of modes supported by this LCD Monitor. PROBLEM Picture is unclear and unstable The picture i
Summary of the content on the page No. 18
Touch Screen Driver Installation The PJT155R/ PJT175R/ PJT195RW is available with USB connection. The touch software is located on the enclosed CD-ROM for these operating systems: Windows® 7, VISTA, XP, 2000, ME, 98, NT4.0, CE, XP Embedded, Linux, Apple® Mac OS Please Note: The PJT155R/ PJT175R/ PJT195RW is Microsoft® Windows® HID (Human Interface Device) compatible if you use the USB touch screen interface. No additional software driver is required for general operation of the touc
Summary of the content on the page No. 19
PJT155R/ PJT175R/ PJT195RW Install Instructions If you are using a PC running Windows® 7, VISTA, XP, 2000, ME, 98, NT4.0, follow the instructions below: 1. Power on the PC. 2. Be sure the USB cable is connected from the PC to the LCD display. 3. Download the driver online and execute. 4. Follow the step-by-step instructions as shown on the pop-up windows. If you are using a PC running Windows® XP Embedded, follow the instructions below: Express: 1. Power on the computer. 2. Make s
Summary of the content on the page No. 20
Product Registration and Technical Support Register Your Planar Products Today Thank you choosing Planar. To assure you receive all the benefits of your Planar product and services, register your Planar product today. Visit our website to register your product at http://www.planar.com/support/product_registration.html Cables, Replacement Lamps, Accessories To find cables, replacement lamps and accessories for your Planar projector, LCD monitor, touch screen or other Planar products
