Summary of the content on the page No. 1
MONITOR WITH DVD RECEIVER
KVT-829DVD
INSTALLATION MANUAL
© B54-4555-00/00 (EV)
Summary of the content on the page No. 2
Accessories 1 0 ..........1 ..........1 2 ! ..........1 ..........2 3 @ ..........1 ..........1 4 ..........1 5 ..........1 6 ..........2 7 ..........4 8 ..........4 9 ..........2 | 2 KVT-829DVD
Summary of the content on the page No. 3
Installation Procedure 1. To prevent short circuits, remove the key from the € ignition and disconnect the - terminal of the • If the power is not turned ON (or it is ON, but will be OFF battery. immediately), the speaker wire may have a short-circuit 2. Make the proper input and output wire or touched the chassis of the vehicle and the protection connections for each unit. function may have been activated. Therefore, the speaker 3. Connect the wire on the wiring harness. wire should be c
Summary of the content on the page No. 4
iPod Connection Monitor/Player unit Do not connect. USB device (commercially available) USB connector (iPod) USB device (commercially available) USB connector Accessory ! Wiring harness (Accessory 2) Ground wire (Black) Ground wire (Black) The cable (Accessory 3) is FUSE ( 5A ) fixed with a chassis using Connector A harness band (Accessory Battery wire (Yellow) BATT !). 8 6 4 2 Ignition wire (Red) 7 5 3 1 ACC 8 6 4 2 Accessory 0 7 5 3 1 (ISO–JASO) Accessory 4 Connector B Antenna Cord (ISO)
Summary of the content on the page No. 5
Receiver unit Accessory ! The cable (Accessory 3) is fixed with a chassis using Accessory 3 harness band (Accessory !). Receiver unit FM/AM antenna input Wiring harness (Accessory 1) ILLUMI Ground wire (Black) - (To car chassis) A REVERSE REMO.CONT MUTE A ANT CONT P. CONT Battery EXT. CONT If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power sou
Summary of the content on the page No. 6
Connecting Wires to Terminals Connector Function Guide 2WARNING Pin Numbers for Cable Colour Functions Connecting the ISO Connector ISO Connectors The pin arrangement for the ISO connectors depends on External Power the type of vehicle you drive. Make sure to make the proper Connector connections to prevent damage to the unit. A-4 Yellow Battery The default connection for the wiring harness is described in A-5 Blue/White Power Control 1 below. If the ISO connector pins are set as described i
Summary of the content on the page No. 7
System Connection To Relay Box Accessory @ Receiver unit ■ Front Preout • Audio left output (White) • Audio right output (Red) ■ Rear Preout • Audio left output (White) • Audio right output (Red) ■ Subwoofer Preout • Audio left output (White) • Audio right output (Red) ■ Audio/Visual input 2 • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) ■ Audio/Visual input 1 • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) ■ Rear View Camera Inpu
Summary of the content on the page No. 8
iPod iPod iPod AUDIO IN VIDEO IN Optional Accessory Connection iPod (commercially available) KCA-iP300V (Optional Accessory) Audio Input Resistance-free stereo type mini plug (3.5Ф) Audio Output (Black) Visual Input Resistance-free mini plug (3.5Ф) Monitor/Player unit Visual Output (Yellow) USB terminal USB terminal (iPod) iPod cannot be connected. USB terminal Receiver unit Accessory 3 Connection cable Connection cable (Included in the Disc changer) (Included in the Navigation System) Disc C
Summary of the content on the page No. 9
Installation for Monitor/Player Unit Firewall or metal support Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw Metal mounting strap Accessory 5 (commercially available) (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). Installation for Receiver Unit 1. Attach the installation brackets 9
Summary of the content on the page No. 10
Removing Monitor/Player Unit Removing the Hard Rubber Frame Removing the Unit (escutcheon) 1. Remove the hard rubber frame by referring to the removal procedure in the section . remove the two locks on the lower level. 2. Remove the Hex-head screw with integral washer Lower the frame and pull it forward as shown in (M4 × 8) on the back panel. the figure. 3. Insert the two removal tools 6 deeply into the Remo
Summary of the content on the page No. 11
Summary of the content on the page No. 12
