Summary of the content on the page No. 1
Z910DVD(K)Cover 02.12.13 6:30 PM Page 1
DVD-RECEIVER
Z910DVD[K]
INSTRUCTION MANUAL
Z910DVD[R]
This player has been designed to play back the DVD soft-
ware which has been encoded for specific region areas. It
cannot play back the DVD software encoded for other
region areas than the region areas for which it has been
designed.
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the
best performance from your new DV
Summary of the content on the page No. 2
Z910DVD(K)_U.S 02.12.13 6:40 PM Page 2 Contents Warning .......................................3 for Non-Fading Output........................22 Tuner features 4.Phase for Non-Fading Output..............22 Tuning .....................................................31 Safety precautions ......................4 Spatializer® Control Setting ..................22 Direct Access Tuning..............................32 Handling discs .............................6 Dual Zone System....................
Summary of the content on the page No. 3
Z910DVD(K)_U.S 02.12.13 6:40 PM Page 3 2Warning NOTE 2CAUTION Menu settings This equipment has been tested and found Use of controls or adjustments or Menu System.........................................50 to comply with the limits for a Class B digital performance of procedures other than those Security Code.........................................51 device, pursuant to Part 15 of the FCC Rules. Touch Sensor Tone.................................52 specified herein may result in hazardous The
Summary of the content on the page No. 4
Z910DVD(K)_U.S 02.12.13 6:40 PM Page 4 Safety precautions IMPORTANT INFORMATION 2WARNING 2CAUTION About the disc changer to be To prevent injury or fire, take the To prevent damage to the machine, connected: following precautions: take the following precautions: To connect a disc changer having the "O-N" • Insert the unit all the way in until it is fully • Make sure to ground the unit to a negative switch to this unit, set the "O-N" switch to locked in place. Otherwise it may fall out of 12V
Summary of the content on the page No. 5
Z910DVD(K)_U.S 02.12.13 6:40 PM Page 5 • The illustrations of the display and the Cleaning the Disc Slot NOTE panel appearing in this manual are As dust can accumulate in the Disc slot, examples used to explain more clearly how • If you experience problems during clean it occasionally. Your Discs can get the controls are used. Therefore, what installation, consult your Kenwood dealer. scratched if you put them in a dusty Disc appears on the display in the illustrations slot. • If the unit fai
Summary of the content on the page No. 6
Z910DVD(K)_U.S 02.12.13 6:40 PM Page 6 Handling Discs Playing a Disc that is dirty, scratched Storing Discs Checking New Discs for Burrs or warped can cause the sound to •Do not store discs in areas exposed to When playing a new disc for the first time, direct sunlight (such as a car seat or the check that there are not any burrs stuck to skip and the unit to operate dashboard) or other hot places. the perimeter of the disc or in the central incorrectly, resulting in worsened hole. discs with
Summary of the content on the page No. 7
Z910DVD(K)_U.S 02.12.13 6:40 PM Page 7 Do Not Load CD Accessories in Slot Do Not Use Special Shape Discs Do Not Use Discs with Sticker on the Do not use commercially available CD Be sure to use round shape Discs only for Labelled Side accessories that can be loaded into the disc this unit and do not use any special shape Do not use the disc with the label sticker slot, such as stabilisers, protective sheets, Discs. Use of special shape Discs may stuck on it. or CD cleaning discs, since they c
Summary of the content on the page No. 8
Z910DVD(K)_U.S 02.12.13 6:41 PM Page 8 Before Use This player has been designed to play back the DVD Icons on the DVD discs software which has been encoded for specific region Icon Description areas. It cannot play back the DVD software encoded for other region areas than the region areas for which it has Indicates the region code where the disc can be been designed. ALL played. The Z910DVD[K] (for USA and Canada) will playback any disc whose region number is (or ). 1 ALL Number of
Summary of the content on the page No. 9
Z910DVD(K)_U.S 02.12.13 6:41 PM Page 9 playback only, while some are P.B.C.-compatible and are capable of Track number (CD, VCD) various special playback control operations. This player can play both A track is also a section of video and audio recorded in a disc. The of these VCDs. numbers assigned to individual tracks are referred to as the track MPEG: Moving Picture Expert Group (DVD, VCD) numbers. This is an international standard for digital video and audio With most of music Discs, a t
Summary of the content on the page No. 10
Z910DVD(K)_U.S 02.12.13 6:41 PM Page 10 General features Power Release button Turning on the power: SRC/ Press the SRC (source) button. PWR OFF u ¢ S.A FM NOTE Turn the power on before carrying out the following procedures. Turning off the power: DSP AUD Press the PWR OFF button for at least one second. 3-D DAB PWR OFF NOTE The status of the Security Code function (page 51) is displayed XOVER DISP NAME.S MENU NF AUTO AME whenever the power is switched on. "CODE ON" : Security Code has been
Summary of the content on the page No. 11
Z910DVD(K)_U.S 02.12.13 6:41 PM Page 11 NOTE Attenuator • The mode switches to the next mode from any mode which This function allows you to turn down the volume quickly. cannot be used. Turning Attenuator On/Off: • The external disc control mode will differ depending on the unit Press the ATT button to switch the attenuator on and off. that is connected. When the attenuator is off, the volume returns to the original •You cannot use the AUX input function of the optional switching level. adap
Summary of the content on the page No. 12
Z910DVD(K)_U.S 02.12.13 6:41 PM Page 12 General features See "Icon/Spectrum analyzer Select" in the menu setting (page Switching Display Mode 53). You can select the display mode of this unit. •You cannot switch into the "Display Type C" during the standby mode. Changing the Display Mode: • When discs recorded by DTS are played spectrum analyzer isn’t Each time you press the DISP button, the display mode displayed. switches as follows: "Display Type A" Divide the display into the uppe
Summary of the content on the page No. 13
Z910DVD(K)_U.S 02.12.13 6:41 PM Page 13 name function (page 48). Note that depending on the unit, display may not be possible. • If you try to display the name of a disc that does not have one, "NO NAME" is displayed instead. • When there is an attempt to display the title of a disc for which the disc title/track title has not been recorded, "NO TEXT" is displayed for CD and "NO TITLE" is displayed for MD. • Depending on the type of characters of the CD Text, some characters may not be displa
Summary of the content on the page No. 14
Z910DVD(K)_U.S 02.12.13 6:41 PM Page 14 General features In External disc control mode: Switching the Lower Part Display This function switches the type of information on the lower part display when the display mode is "Display Type A". Spectrum Analyzer + Clock 1 Press the S.A button to enter the display control mode. Date + Function indicator 2 Each time you press the FM or AM button, the lower part display changes as follows: Disc name (DNPS) (only when being preset) + Function indicator I
Summary of the content on the page No. 15
Z910DVD(K)_U.S 02.12.13 6:41 PM Page 15 3 Press the S.A button to end the display control mode. Switching Full-Screen Display NOTE This function switches the type of information on the display when the display mode is "Display Type C". • For display mode selection, see "Switching display mode" (page 12). Each time you press the S.A button, the full screen display • If the display mode is set to "Display Type B", you can turn on changes as follows: or turn off the clock. • The same items canno
Summary of the content on the page No. 16
Z910DVD(K)_U.S 02.12.13 6:41 PM Page 16 General features Switching Display during the Standby mode Theft Deterrent Faceplate This function switches the type of information on the display The faceplate of the unit can be detached and taken with you, in standby mode. helping to deter theft. Removing the Faceplate: 1 Press the SRC button repeatedly to select the standby mode. "ALL OFF" is displayed when the standby mode is selected. 1 Press the release button and drop open the faceplate. 2 Each
Summary of the content on the page No. 17
Z910DVD(K)_U.S 02.12.13 6:41 PM Page 17 Audio effect control features 3-D AUD/Q ¢ FM DSP AUD 2CAUTION 3-D DAB PWR OFF Do not set the right side of the faceplate in the faceplate bracket first, when reattaching the faceplate. Doing so may cause the XOVER DISP NAME.S AUTO AME MENU NF connector on the faceplate bracket to malfunction. 2 Press the right side of the faceplate until it locks. 4 XOVER AM/NF Selecting mode Setting value — 17 —
Summary of the content on the page No. 18
Z910DVD(K)_U.S 02.12.13 6:41 PM Page 18 Audio effect control features System Q Speaker Setting You can recall the best audio setting preset for different types This function allows you to adjust the setting that is recalled of the music. with the System Q, according to types of speakers. Switching the Preset Sound Setting: 1 Press the SRC button repeatedly to select the standby mode. Each time you press the Q button, the preset sound setting "ALL OFF" is
Summary of the content on the page No. 19
Z910DVD(K)_U.S 02.12.13 6:41 PM Page 19 Audio Control Setting: 1.Bass Center Frequency Adjust various parameters of sound quality. Adjust the center frequency of the bass. Display and setting: 1 Press the AUD button for at least one second to enter the "Bass FRQ" : 60 / 70 / 80 / 100 (Only when the bass quality control mode. factor is set to 1.00, 1.25 or 1.50) / 150 (Only 2 Selecting mode when the bass quality factor is set to 2.00) Hz. Press either the FM or AM button. Each time the button
Summary of the content on the page No. 20
Z910DVD(K)_U.S 02.12.13 6:41 PM Page 20 Audio effect control features 9.Treble Level 5.Middle Center Frequency Adjust the treble level. Adjust the center frequency of the middle. Display and setting: Display and setting: "TRE" : - 9 – 0 – + 9 "MID FRQ" : 0.5 / 1.0 / 1.5 / 2.0 kHz. 10.Balance Level 6.Middle Level Adjust the balance level. Adjust the middle level. Display and setting: Display and setting: "Balance" : Left 15 – 0 – Right 15 "MID" : - 9
