Summary of the content on the page No. 1
H-CMMD4040
MULTIMEDIA DVD RECEIVER WITH MOTORIZED 7 TFT DISPLAY AND BUILT-IN
TV-TUNER
Instruction manual
DVD 7 TFT
Summary of the content on the page No. 2
Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents Tabl of contents........................................................................................................................................2 Importansafeguards.................................................................................
Summary of the content on the page No. 3
Important safeguards · Using the device at temperature below -10º may cause the breakage of the device. BEFORE USING PLEASE HEAT UP THE PASSENGER COMPARTMENT TO THE RECOMMENDED TEMPERATURE! · Read carefully through this manual to familiarize yourself with this high-quality sound system. · Disconnect the vehicle's negative battery terminal while mounting and connecting the unit. · When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage ra
Summary of the content on the page No. 4
Installation/ connection First complete the electrical connections, and then check them for correctness. Installation opening This unit can be installed in any dashboard having an opening as shown on the picture. The dashboard should be 4.75 5.56 mm thick in order to be able to support the unit. 1. Insert mounting collar into the dashboard, and bend the mounting tabs out with a screwdriver. Make sure that lock lever is flush with the mounting collar (not projecting outward). 2. Secure the r
Summary of the content on the page No. 5
Electrical connection Amplifier jacks 5
Summary of the content on the page No. 6
Caution: Do not interchange the connection of the wiring!!! For some car models you may need to modify wiring of the supplied power cord. Contact your authorized car dealer before installing this unit. Using the ISO Connector 1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated. 2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit. 3. Cut
Summary of the content on the page No. 7
Panel controls Front panel 1. PWR/MOD button Press POWER button to turn the power on, press and hold for 2 seconds to turn the power off. 2. Adjust angle +/- 3. TFT display 4. WIDE button. Press it to choose screen format - 16:9 or 4:3 5. RESET button 6. OPEN button. Press it to open display 7. EJECT button 8. VOL knob Rotate VOL knob to adjust the volume. 9. IR sensor 10. PRESET STATION [1-6] buttons 7
Summary of the content on the page No. 8
11. SET button (Multi-functional key) 12. Navigation knob (AF, TA, PTY, EON) 13. PLAY/PAUSE button Use this button to start playback. Press it to pause playback. 14. RPT button Use this button to play current track repeatedly. 15. INT button Press it to start intro playing (10 seconds). 16. SEEK +/- (Auto scanning, seek up/down, fast reverse/forward) Use these buttons to enter the manual tuning mode/ seek tuning mode. Use this button to search for the beginning of the previous/ next track, for b
Summary of the content on the page No. 9
Remote control 1. MODE button 2. POWER button 3. BND button 4. Directional buttons for menu selection 5. ENTER button 6. STOP/REVERSE button 7. AMS/PAUSE button 8. ST button 9. LOC/PLAY button 10. VOL +/- button 11. PBC button 12. OSD (On Screen Display) button 13. Digit area 14. PANEL ANGLE ADJUST button 15. OPEN DISPLAY button 16. TITLE button (for DVD only) 17. SUB.T button (for DVD only) 18. SETUP button 19. ANGLE button (for DVD discs only) 20. MUTE button 21. ZOOM button (for DVD/VCD only)
Summary of the content on the page No. 10
24. AUDIO button 25. GOTO button Changing the battery 1. Press the catch and at the same time pull out the battery tray. 2. Insert the 1 x lithium battery, type CR 2025 3V battery with the stamped (+) mark facing upward. Insert the battery tray into the remote control. Warning: Store the battery where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately. Do not recharge, short, disassemble or heat the battery or dispose it in a fire. Do not expose or
Summary of the content on the page No. 11
General operation Reset the unit Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press the RESET button by using a ball-point pen or a similar tool to restore the unit to the original factory settings. Power button Press POWER/MODE button on the unit or POWER on the RC to turn the unit on. Press the POWER/MODE button for 3 seconds to switch off the power. Note: After the unit is off, the volume level and radio current settings will be memorized,
Summary of the content on the page No. 12
- BALANCE control Press the VOL 4 times, then rotate to adjust the balance level. - FADER control Press the VOL 5 times, then rotate to adjust the fader level. - LOUDNESS control Rotate the knob clockwise to activate LOUD ON, rotate anticlockwise to activate LOUD OFF. - EQ control Rotate the knob clockwise to choose the equalizer mode: OFF, POP, ROCK, CLAS, JAZZ. Or press SEL button to increase or decrease the volume, balance, treble, bass, fader control level. Note: · If turning off the power a
Summary of the content on the page No. 13
ST selector During the radio mode press the ST button on the RC to switch left speaker/right speaker/stereo. Adjust angle Press the Adjust angle +/- buttons on the front panel or button on the RC to adjust the TFT Panel angle to your need. Screen setting Press the WIDE button on the front panel to set the screen format: 16:9 or 4:3. Open TFT screen Press the OPEN button on the front panel or OPEN SCREEN button on the RC, TFT panel will be opened automatically. Press again to close. Setting Knob
Summary of the content on the page No. 14
Digital tuner Note: RDS (Radio Data System) service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available, either. Band selection Press MODE button to select Radio mode. Press BND button on the RC once or more to select: FM1, FM2, FM3, FM (OIRT), MW1, MW2. Display will show the wave band, frequency and preset station number if already stored. Manual/ automatic tuning · Manual tuning: Press the +/- buttons on the fron
Summary of the content on the page No. 15
AMS (Auto Memory Store) function · Preset scan: press AMS/PAUSE on the RC to scan all preset stations in the memory of the current band and stay on each memory stations for about 5 seconds. The memory location indicator on the LCD will flash during the process. To stop preset scan, press this button again. · Auto memory store: press AMS/PAUSE on the RC for more than 2 seconds to enter auto store mode. The radio will automatically store the 6 strongest available stations to the 6 preset memories
Summary of the content on the page No. 16
PTY (Program Type) 1. Rotate the navigation knob to choose PTY function. The previous PTY type is shown. 2. Press PTY once again to enter the MUSIC type or press twice to enter the SPEECH type, then use buttons 1 - 6 to select the desired program type (see the following table). 3. When PTY is selected, the radio starts to search corresponding PTY information, and stops if the corresponding PTY information is detected. If there are no keys entered for 2 seconds, previously selected PTY is searche
Summary of the content on the page No. 17
Local/Distance Control In radio mode, press the LOC/PLAY button on the RC to select local or distance reception. a. LOC ON showing on the display, means local reception is turned on; b. _DX_ showing on the display, means distant reception is turned on. Local and distance reception setting can facilitate the radio reception, depending on the location in which the radio is being used. TV operations TV tuning (only when TV antenna is connected) At first, press MODE button to switch the set to TV
Summary of the content on the page No. 18
Glossary PBC (PlayBack Control) PlayBack Control is a menu recorded on the disc with SVCD or VCD2.0 format. For the discs contained PBC, it can playback interactive software with the menu displayed on TV. And if the disc contains still images, it can playback high definition of still image. Title The title is the important part of DVD disc. The memory volume of the disc is rather big, that makes possible to record several films on one disc. For example, if a disc contains three films, they may b
Summary of the content on the page No. 19
Disc operations Discs for playback · This unit can play all digital audio CD, DVD/SVCD/VCD/HDCD/MP3/MP4/WMA/CDDA/ Picture-CD/JPEG/CD-R/-RW/DVD±R/±RW. · The following file types are supported: Audio files: MP3 (*.mp3) WMA (*.wma) Video files: MP4 (*.avi, DIVX3.11/4.0/5.0/6.0 and XVID) MPEG 2(*.vob) MPEG 1(*.dat) Picture file: JPEG (*.jpg) · ISO 9660 or ISO 9660 +Joliet format - Max. 30 characters · Max. Track number is 448 · Max. nested directory is 8 levels ·
Summary of the content on the page No. 20
Playing/ pausing To ensure good system performance, wait until the unit finishes reading the disc information before proceeding. Press the PLAY/ PAUSE button on the front panel or LOC/PLAY on the RC to start the playback. Pause In pause mode press the PLAY/ PAUSE button on the front panel or AMS/PAUSE on the RC to resume the playback. STOP Press button to suspend playback. Press it again the stop playback. Press PLAY/PAUSE to resume playback. Playing the previous/ next track 1. During playback p
