Summary of the content on the page No. 1
EXCELLENCE
by
H-CMD4007
MULTIMEDIA DVD/CD/MP3 RECEIVER WITH BUILT-IN 3” TFT DISPLAY AND TV TUNER
Instruction manual
DVD/CD/MP3 3” TFT -
Summary of the content on the page No. 2
Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents Table of contents ...............................................................................................................................................2 Important safeguards .....................................................................
Summary of the content on the page No. 3
Important safeguards Using the device at temperature below -10º may cause the breakage of the device. Before using please heat up the passenger compartment to the recommended temperature! Disconnect the vehicle's negative battery terminal while mounting and connecting the unit. When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit. Do not attempt to disassemble the unit. Laser beams from
Summary of the content on the page No. 4
Accessories Mounting Bracket (Half Sleeve) 1 pc Mounting Screw M5 1 pc Rubber 1 pc Removable Trim Ring equipped on the unit 1 pc Remote Control 1 pc Release key 2 pcs Screws 4 pcs Mounting strap 1 pc USB cable 1 pc Protective case 1 pc Customer information 1 pc Warranty card 1 pc Instruction manual 1 pc 4
Summary of the content on the page No. 5
Installation/connection This unit can be installed in any dashboard having an opening as shown on the picture. The dashboard should be ~ 4.5 – 5.5 mm thick in order to be able to support the unit. First complete the electrical connections, and then check them for correctness. Installation opening 1. Insert the unit holder into the dashboard. 2. Select the appropriate tabs and bend them the tabs 90 degrees to secure the holder in place. 3. Secure the rear of the unit. Fix the rear of the unit to
Summary of the content on the page No. 6
Electrical connection Caution: Do not interchange the connection of the wiring! For some car models you may need to modify wiring of the supplied power cord. Contact your authorized car dealer before installing this unit. 6
Summary of the content on the page No. 7
Controls Front panel 1. PWR/BACK button 2. / buttons 3. VOL knob/MENU button 4. PTY/ME/PLAY/PAUSE button 5. IR window 6. TFT display 7. AMS button 8. REL button 9. TA/SET/RPT button 10. AF / MOD button 11. BAND button 12. AV IN button 13. USB slot 7
Summary of the content on the page No. 8
Inner panel 14. SD/MMC slot 15. Disc loading slot 16. EJECT button 17. RESET button 8
Summary of the content on the page No. 9
Remote control 1. POWER button 2. MODE button 3. DISP button 4. P/N button 5. SETUP button 6. / , / , , ENTER buttons 7. TITLE button 8. PLAY button 9. ANGLE/SCAN button 10. VOL-/VOL+ buttons 11. CLEAR button 12. RPT/SEEK- button 13. 10+ button 14. (0-9) number buttons 15. GOTO button 16. BACK button 17. MUTE button 18. SLOW+ button 19. SLOW- 20. MENU button 21. PBC button 22. STOP button 23. AMS/PROG button 26. BAND/A-B button 24. RDM/SEEK+ button 27. ST/AUDIO button 25. LOC/SUB-T button
Summary of the content on the page No. 10
Changing the battery 1. Pull out the battery tray. 2. Insert the 1 x lithium battery, type CR 2025 3V battery with the stamped (+) mark facing upward. Insert the battery tray into the remote control. Warning: Store the battery where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately. Do not recharge, short, disassemble or heat the battery or dispose it in a fire. Do not expose or bring into contact the battery with other metallic materials. Doing
Summary of the content on the page No. 11
General operations Reset the unit Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press REL button to remove the detachable front panel. Using a ballpoint pen or other pointed object, press RESET button to complete the initialization procedure. Power on/off Press PWR/BACK button on the panel or POWER button on the RC to turn the unit on. Press it for a long time on the panel or press shortly on the RC to turn the unit off. Note: After the unit i
Summary of the content on the page No. 12
Press / buttons on the panel or press the cursor buttons on the RC to select the submenu: AUDIO => PICTURE => SETUP. Press MENU button on the panel or ENTER button on the RC to enter the submenu selected. Press / buttons on the panel or press the cursor buttons on the RC to select the setting: For AUDIO submenu: VOLUME => BASS => TREBLE => BALANCE => FADER => EQ => LOUD => SUB.W. For PICTURE submenu: BRIGHT => CONTRAST => COLOR => TINT => DEFAULT. For SETUP submenu: SYSTEM => CLOCK. W
Summary of the content on the page No. 13
Digital tuner operations Note: RDS (Radio Data System) service availability varies with areas. Please understand if RDS service is not available in your area, the following service is not available, either. Band selection Press BAND/A-B button on the RC or BAND button on the panel to select a band: FM1, FM2, FM3, MW1 (AM1), MW2 (AM2). Display will show the wave band and frequency. Automatic/ Manual tuning Automatic tuning: Press / buttons to start auto searching the station. Manual tuning: Pres
Summary of the content on the page No. 14
Note: Press repeatedly ME/PLAY/PAUSE button to change sequence number of stored station. To recall a station: - Select a band (if needed) - Press a number button (1-6) briefly to recall a stored station. Or: - Select a band (if needed) - Press SET/RPT button to select the stored station. Preset scan function Press AMS button on the panel or PROG/AMS button on the RC to scan all preset stations in the memory of the current band and stay on each memory stations for several seconds. To stop preset
Summary of the content on the page No. 15
AF: Alternative frequencies – frequency list of broadcasting station transmitting the same program. AF function Press AF button to switch on/off mode. Symbol “AF” will appear on the display. Note: The tuner will return to Alternative Frequencies whenever the reception signals getting worse. “Alarm” will be displayed when an emergency broadcasting is received. Meanwhile sound output level will be adjusted to the preset output level automatically when the volume control is set at minimum. PTY func
Summary of the content on the page No. 16
Disc/USB/MMC/SD operations Disc glossary PBC (PlayBack Control) PBC is a menu recorded on the disc with SVCD or VCD2.0 format. For the discs contained PBC, it can playback interactive software with the menu displayed on TV. And if the disc contains still images, it can playback high definition of still image. Title The title is the important part of DVD disc. The memory volume of the disc is rather big, that makes possible to record several films on one disc. For example, if a disc contains thre
Summary of the content on the page No. 17
Discs for playback This unit can play disc types: DVD/DVD±R/DVD±RW/CD/CD-R/CD-RW. Compatible with formats: DVD/SVCD/VCD/HDCD/MP3/MP4/WMA/CDDA/Picture-CD/JPEG/MPEG4. The following file types are supported: Audio files: MP3 (*.mp3) WMA (*.wma) Video files: MP4 (*.avi, DIVX3.11/4.0/5.0/6.0 and XVID) MPEG 2(*.vob) MPEG 1(*.dat) Picture file: JPEG (*.jpg) ISO 9660 or ISO 9660 +Joliet format - Max. 30 characters Max. Track number is 448 Max. nested directory i
Summary of the content on the page No. 18
Loading a disc 1. Turn the power on. 2. Press REL button on the panel to open the front panel. 3. Insert the disc with the printed side facing upward into the slot. 4. Close the front panel. 5. Press MODE button to select the DVD mode. The monitor will show the disc content. The DVD disc will play automatically. When the MP3 disc is loaded, press PLAY to start the playback. 6. To eject the disc, first press REL button to open the front panel. 7. Press EJECT button on the base to eject the disc.
Summary of the content on the page No. 19
After inserting the disc, playback will start automatically. Or press ME/PLAY/PAUSE button on the panel or PLAY button on the RC to start playback. Press ME/PLAY/PAUSE button on the panel to go into pause mode. In pause mode press it again or press PLAY button on the RC to resume the playback. Stop playback During playback press STOP button on the RC to stop playback. Press ME/PLAY/PAUSE button on the panel or PLAY button on the RC to start playback for the place where it was stopped. Press STOP
Summary of the content on the page No. 20
Repeat A-B function (for DVD/VCD discs) 1. During playback, press the BAND/A-B button on the RC at the starting point of section you want to repeat. 2. Press the BAND/A-B button again at the ending point of the section you want to repeat. Section A-B repeating starts. 3. Press the button again to cancel the A-B repeat function. Random playback (for CD/VCD/MP3 only) During disc playback press the RDM/SEEK+ button on the RC to select start random playback. Press again to cancel. TV type select Pre
