Summary of the content on the page No. 1
HMLCD15
15-inch LCD Monitor
User Manual
Video Systems
www.honeywellvideo.com
1-800-796-CCTV
© 2004 Honeywell International Inc.
All rights reserved. No part of this publication may be reproduced by
any means without written permission from Honeywell Video Systems.
The information in this publication is believed to be accurate in all
respects. However, Honeywell Video Systems cannot assume
responsibility for any
Summary of the content on the page No. 2
SECTION 5: SPECIFICATIONS ISSUE DATE REVISIONS A April 2004 Initial Release (PCN 1630) LCD Type TFT Color XGA Screen 15” (diagonal) Size PC Input Signal RGB Analog Type 15-Pin D-Sub Sync H-Freq 31.5~60KHz V-Freq 56-75Hz Display Color 16,777,216 Resolution 1024 × 768 (75Hz) OSD Controls Auto Geometry, Auto Brightness, Contrast, H/V Position, etc. Power Management VESA DPMS Power Consumption 30W (max) Power Saving Mode Under 1W
Summary of the content on the page No. 3
4.4 LIMITED WARRANTY FCC COMPLIANCE STATEMENT Honeywell International Inc. ("Seller"), 1305 Waters Ridge Drive, Lewisville, TX 75057, INFORMATION TO THE USER: This equipment has been warrants this monitor to be in conformance with its own plans and specifications and to tested and found to comply with the limits for a Class A digital be free from defects in materials and workmanship under normal use and service for a device, pursuant to Part 15 of the FCC rules. These limits are per
Summary of the content on the page No. 4
SECTION 4: TROUBLESHOOTING AND MAINTENANCE EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol within 4.1 TROUBLESHOOTING an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous No Power voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. • Make sure the Power cable is plugged to the wall and the back of the monitor. The exclamation point wit
Summary of the content on the page No. 5
NOTES: WARNINGS Installation and servicing should be performed only by qualified and experienced personnel. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. SAFEGUARDS This product is made with consideration of the maximum safety of users. However, in order to prevent all possible accidents and financial lost, the monitor must be installed in the appropriate environment. Read instructions and follow all safeguards. POWER WARNINGS 1. Insert the
Summary of the content on the page No. 6
SAFEGUARDS, CONTINUED 3.4 GETTING OPTIMAL PICTURE Step 1: Window’s background or “H” character should be displayed 2. Do not place candlelight, mosquito coils, or cigarettes on top of the on your screen. monitor or install it close to heating appliances. Doing so may damage the product or create a fire danger. The product should be situated away from heat sources such as radiators, heat Step 2: Adjust the screen to the center of the Display (LCD) by using registers, stoves, or ot
Summary of the content on the page No. 7
3.3 ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE, SAFEGUARDS, CONTINUED CONTINUED CLEANING AND GENERAL USAGE Using HOTKEY 1. For added protection of this unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it Frequent adjustments such as auto-geometry, Brightness, from the wall outlet and disconnect the cable system. This will Contrast, Audio-volume, Audio-Mute, and Source (selected in prevent damage to the unit due to lightning and p
Summary of the content on the page No. 8
PURCHASE INFORMATION 3.3 ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE, CONTINUED Date Purchased: OSD Menu Description OSD Horizontal Position Select OSD Menu horizontal position. Serial Number: Vertical position Select OSD MENU vertical position. Timeout Time after which OSD MENU leaves screen. Location Installed: Transparency Adjust the transparency of the OSD Menu. English Language French Select one of the five languages. German Italian Spanish Advanced Horizontal P
Summary of the content on the page No. 9
3.3 ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE, TABLE OF CONTENTS CONTINUED SECTION 1: INTRODUCTION ............................................................... 1 OSD Menu Description 1.1 INTRODUCTION ..........................................................................1 The following table describes the OSD menu and a description 1.2 FEATURES...................................................................................1 of each option. 1.3 TFT LCD PANEL....................
Summary of the content on the page No. 10
TABLE OF CONTENTS, CONTINUED 3.3 ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE, CONTINUED SECTION 4: TROUBLESHOOTING AND MAINTENANCE................. 19 4.1 TROUBLESHOOTING................................................................19 On-Screen Display (OSD) Control Adjustment No Power..................................................................................19 Poor Picture Quality..................................................................19
Summary of the content on the page No. 11
SECTION 1: INTRODUCTION 3.2 PRESET MODE CHART, CONTINUED The monitor is compatible with additional modes within one of 1.1 INTRODUCTION the following specified frequency ranges, provided they are different at least for one of the following: Honeywell's HMLCD15 TFT Color LCD Display features a 15.0" Horizontal Frequency: ±1 KHz viewable active matrix LCD screen, with outstanding 1024 x 768 Vertical Frequency: ±1 Hz pixel resolution. When used in PC based applications the HMLCD15
Summary of the content on the page No. 12
3.2 PRESET MODE CHART, CONTINUED 1.3 TFT LCD PANEL Preset Mode Table Black spots (pixels that do not light) or luminescent spots (pixels that are always lit) may appear on the screen because of the Horizontal Pixel 640 640 640 640 720 800 800 intrinsic characteristics of TFT LCD technology. This is neither a Frequency KHz 31.444 31.469 37.862 37.500 31.440 35.156 37.879 malfunction nor a defect in the monitor. The warranty period for Period (T1) ms 31.778 31.778 26.413 26.667 31.77
Summary of the content on the page No. 13
USER MANUAL 3.2 PRESET MODE CHART 1.4 CONTENTS OF PACKAGE 1. LCD Monitor 2. User Manual 3. VGA Cable Timing Charts The monitor shall be capable of supporting the following video timings: VIDEO (T4) Active SYNC (T3) Back Poach (T5) Front Poach Synch Width (T2) 4. Sound Cable 5. AC/DC 6. Installation (T1) Period Adapter Disk Input Timing Limits H-Sync Pulse Width 1.0 µs ≤ Sync Pulse Width ≤ 6.0 µs. V-Sync Pulse Width 0.04ms ≤ Sync Pulse Width ≤ 0.5ms 7. Powe
Summary of the content on the page No. 14
SECTION 3: NOTES: OPERATION 3.1 POWER MANAGEMENT This monitor is equipped with DPMS (Display Power Management Signaling) function which automatically switches to power saving mode (less than 5 watts consumed) when the computer is left unattended. Although the monitor can be left in power saving mode for longer periods, it is recommended that you turn it off after your daily work. The DPMS function requires support from the computer system of any software DPMS function currently be
Summary of the content on the page No. 15
NOTES: SECTION 2: CONTROLS AND CONNECTIONS 2.1 CONTROLS – FRONT PANEL A B C D E F G H J I K A AV1 F AUTO/EXIT LAMP B PC G BRT C SOURCE H CONT D CH I VOL E MENU/SEL J MUTE K POWER BUTTON Rev. A 8 HMMU000880 Rev. A 5 HMMU000880 04/08/04 04/08/04
Summary of the content on the page No. 16
2.2 CONTROLS – REAR PANEL 2.3 INSTALLING THE MONITOR DRIVER D C B E A You can achieve an optimal resolution and scanning rate by F G installing the monitor driver as follows: 1. Insert the monitor driver diskette into the floppy diskette drive and run INSTALL.EXE. 2. Select the monitor model then press OK. The installation will begin immediately. 2.4 VGA CABLE DVR or VCR PC A 15-pin D-Sub connector is used as the input signal connector. Pin and input signal are shown in the t
