Summary of the content on the page No. 1
50 - - 002 SERIES 1181281
50 - - 014 SERIES 1181280
FORD EXPEDITION
r
5. T -
FOR USE IN VEHICLES WITH FACTORY INSTALLED
OVERHEAD CONSOLE ONLY.
Apr. 14, 1999
INSTALLATION INSTRUCTION # 44 -
Printed in the U.S.A.
0018D
is installation: Materials provided for th
7. Audiovox Series 640/650 Video Module
6. 1/8" Drill Bit 10TORX bit driver
4. Razor knife or similar tool 3. Awl or scribe point tool or s
Summary of the content on the page No. 2
1 Nut, 6 - 32 HH KEPS 8 2 Screw, # 6 x 3/8 PPH TAB 13 3 Screw, # 8 x 9/16 PWH TAB 2 4 Screw, 6 - 32 x 1/2 PPH 4 5 Screw, 6 - 32 x 3/4 PPH 10 6 Screw, # 8 x 1 1/4 PWH TAB 2 7 Screw, # 8 x 1 1/2 PWH TAB 1 8 Screw, # 8 x 1 3/4 POH TAB Z1 2 9 4 10 2 11 Convoluted Tube, 1/2" ID X 3" 1 12 1 13 1 14 Pod Mounting Bracket 4 15 2 16 1 17 1 18 1 19 1 INSTALLATION INSTRUCTION # 44 - Apr. 14, 1999 . 2 Printed in the U.S.A 0018D Overhead Console Pl
Summary of the content on the page No. 3
3
Summary of the content on the page No. 4
I. REMOVAL OF O.E.M. EQUIPMENT. - f - d twist. using two (2) # 8 x 9/16" PWH screws (item 3 pg2). 4 Figure 3 Figure 2 See Figure 2 and 3. through modified louver opening and secure in place ided in kit 2. Install plywood block (item 18 pg 2) prov Figure 1 and remove indicated headliner. See Figure 1. A/C vent hole with arrow pointing forward. Cut 1. Place template provided (item 12 pg 2) over c
Summary of the content on the page No. 5
- # 8 x 1 1/4" PWH screw (it em 6 pg 2). See Fig. 4. tube (ite 5. Remove and retain two (2) OEM screws located 5 Figure 6 OEM screws. See Figure 6. front bracket (item 13 pg 2) using OEM holes and at front of OEM bracket near windshield. Mount Figure 5 chaffing against bracket. m 11 pg 2) around wire harness to prevent toward driver’s side of bracket. Install convoluted with OEM screws. See Figure 5. Ro
Summary of the content on the page No. 6
- - pillar to floor. Route power and ground leads forward to fuse box area. Connect power wire controlled power source per sensor extension, etc.) to VCP location. Connect per s ) screws. See Fig. 8. 6 Figure 9 removing eight ( 8 ) OEM screws. See Figure 9. 2. Remove and retain secondary light and pod assembly by Figure 8 assembly by removing four ( 4 1. Remove and retain OEM
Summary of the content on the page No. 7
3. Attach four (4 ) pod mounting brackets (item 14 pg 2) to front and rear of be - 32 X 1/2" screws (item 4 pg 2) and four (4) 8 - 32 KEPS X 3/8" PPH screws (item 2 pg 2) As shown. See Figure 11. 7 Figure 11 console (item 19 pg 2) with eight ( 8 ) # 6 4. Install and secure O.E. bezel in overhead Figure 10 nuts (item 1 pg 2). See Figure 10. zel with four (
Summary of the content on the page No. 8
Note: 8 Figure 13 accessible. Be sure light wiring is Figure13. overhead console with six ( 6 ) OEM screws. See 6. Install and secure secondary light pod assembly in Figure 12 See Figure 12. OEM screws in front assembly as shown. light and pod assembly, replace two ( 2 ) 5. Remove two (2) plastic tabs on secondary
Summary of the content on the page No. 9
(5) # 6 X 3/8" PPH screws (item 2 pg 2). See Figure 14. four ( 4 ) 6 - 32 X 3/4" screws (item 5 pg 2 ) and four (4) IV. INSTALLATION OF OVERHEAD CONSOLE. d to the vehicle. 9 Failure to do so may cause damage to console or installed components. Caution: Do not overtighten screws. Use extra support for the console until secure Figure 15 check for proper clearance and function. console openings. Manu
Summary of the content on the page No. 10
1. 2. using two (2) 6 - 32 X 3/4" screws bracket (Item 3). 3. Secure front of console using one ( 1 ) # 8 X 1 1/2" 4. - 10 Figure 19 Figure 17 in step 2. 32 X 3/4" screws previously installed 5. Tighten 6 front mounting bracket. See Fig. 17. pg 2) in dimple area at front of console through 1 1/4" PWH screw (item 6 Install one ( 1 ) # 6 x secondary pod and light assembly. See Figure 17. PWH screw (item 7) in front
Summary of the content on the page No. 11
with video system. your area. Note: Make sure that wires do not get pinched between bosses on video system and console. - pg 2). Caution: Do not overtighten screws. 18. Do not overtighten screws. 11 headliner. See Figure 19. o plywood support installed above dimples at rear of overhead console to secure rear of cons
Summary of the content on the page No. 12
12 CUT ON DOTTED LINES
