Summary of the content on the page No. 1
VOH1332
Owner’ s/Installation
Manual
13.3” Flip-Down In Vehicle
Entertainment System
Audiovox Electronics Corporation
150 Marcus Blvd.
Hauppauge, NY 11788
1-800-645-4994
Summary of the content on the page No. 2
Features - TFT Active Matrix Color 13.3” LCD - 3 Channel A/V Switching Built-In - Audio Amplifier, Volume Control, and Headphone Jacks Built-In - Game/Camcorder A/V Input Jacks - Backlit Controls for easy Night Operation - “Hide-Away” Screen when not in Use - Built-In TV Tuner - Infrared Remote Control Repeater Circuit (for Wireless VCP, and Tuner Functions) (VCP must be purchased separately) C1 C2 Package Contents A) VOH1332 Video Flip Down Pod- (p/n VOH1332) (not shown) B) Source Component Har
Summary of the content on the page No. 3
Rear Panel Feature 7 6 4 11 11 5 11 11 12 3 2 8 1 9 10 12 1) Left RCA Out: Hook-up for left audio out (white female RCA jack) 2) Right RCA Out: Hook-up for right audio out (red female RCA jack) 3) Video Out: Hook-up for video out (yellow female RCA jack) 4) Power Harness Connection: This plug connects to the power harness mating plug 5) Optional Wired Headphone Connections: Green is right positive, Gray is left positive and Black is the ground. Minimal load requirement is 4Ω. Additional speak
Summary of the content on the page No. 4
Front Button Panel Features 1 2 3 4 5 6 7 8 9 1) Power: This button turns the VOH1332 on and off. Dimly lit when in stand-by mode. 2) Channel Δ ∇: Pressing Δ will select higher programmed channels and pressing ∇ will select lower programmed channels than current channel. 3) Volume Δ ∇: Pressing Δ will raise the volume and pressing ∇ will lower the volume. 4) Select: Each press of this button selects the next source (1-3). Note that some sources produce an image, depending upon whether compo
Summary of the content on the page No. 5
General Installation Approach 1) Before beginning installation, please refer to warning on page 10. 2) Decide upon system configuration and options that will be installed (ie: what components, nd VCP, remote headphones, 2 VCP, etc.). 3) Review all manuals to become familiar with electrical requirements and hook ups. 4) Decide upon mounting locations of all components and method of mounting. 5) Prep the vehicle by removing any interior trim necessary to gain access to vehicle power hook up point
Summary of the content on the page No. 6
Vehicle Preparation 1) Locate vehicle power source. Generally this is best found near the vehicle’ s fuse block, which is usually (though not always) under the steering wheel area. Locate an accessory hot circuit to tap into video system power. Accessory hot means a circuit that is +12VDC when the ignition key is in either the “ACC’ Y” or “Run” positions, and 0 volts DC when the ignition key is removed from the vehicle. 2) Mounting location and method for the individual components will vary f
Summary of the content on the page No. 7
Wiring Diagram Hook Up Procedure Antenna Power Harness TV antenna Item 1 (If applicable) 1) Connect the power harness to the mating connector on the video pod. 2) Connect the power harness to the Red: +12 VDC Black: Ground vehicle’ s electrical system by tapping (Accessory Cir.) into an accessory hot line. 3) Verify all functions of the system before mounting of the finished assembly. Power Antenna Connector Connector (2-pin) Optional Remote Headphone Stations Stereo Headphone Jack Spade Gre
Summary of the content on the page No. 8
Source Component Harness Hook Up Connect to Mini-DIN connector in area shown. A cable tie may be used in holes provided for strain relief. To connect both an FM modulator and wireless headphone transmitter (such as the WHS100,) plug in two RCA “Y” adapters into the left and right audio out RCA jacks on the VOH1332. Using two dual RCA cables, plug the left audio inputs of the modulator and wireless transmitter into the left output “Y” adapter and the right audio inputs into the right output
Summary of the content on the page No. 9
Remote Control Functionality 1 TELEVISION CONTROLS: 2 1) TV Power: Turns unit on/off 3 2) TV/Video: Toggles between 3 available sources; Tuner/VCP/DVD (VCP2) 3) Mute: Mutes headphone audio 4) 0-9: Numbers for channel selection 4 5) Δ CH: Channel Up 5 6) ∇ CH: Channel Down 6 7) Δ Vol: Volume Up 7 8) ∇ Vol: Volume Down 8 9) Skip/Search: Toggles on/off. Skips channels that are not auto-programmed 10) Write/Erase: Controls manual adding/deleting auto- programmed channels 11 11) Auto-Memory: Program
Summary of the content on the page No. 10
Cut-Away View of Mounting Bosses Roof Structure Screw Boss C3 Note: If longer screws are substituted, care should be taken to prevent piercing the roof, and be sure that pan head screws and washers are used to prevent screws from pulling through the screw boss. Eight screws must be used and secured to solid structure when mounting. Antenna Information The following are a few points to consider in regards to TV reception in a mobile application. Generally in a mobile application, the lower chan
Summary of the content on the page No. 11
Troubleshooting Symptom: Cause: Possible Solution: Picture scrolls or is fuzzy Antenna type or location Change antenna or try antenna in a different location Poor Reception Vehicle is moving Not receiving certain channels Connections Vehicle may be outside of TV signal range. Check antenna connections. Check number of antenna connections- the more connections there are, the greater the chance of signal loss, reduce the number of connectons if possible. Unit will not respond to remote Sensor is b
Summary of the content on the page No. 12
Specifications Video System: NSTC Analog Composite Video (1V P-P, 75Ω) A/V Switching: 3 channels Power: 10-16 VDC, Negative Ground Aux Audio Outputs: Left and Right Variable (800mV max, 8Ω load min.) Left and Right Fixed (300mV typi
Summary of the content on the page No. 13
P/N 1281332 Rev. B Oct. 00
Summary of the content on the page No. 14
Summary of the content on the page No. 15
