Summary of the content on the page No. 1
VOH-641Drop Down Video Monitor
VOH-642 Drop Down TV / Video Monitor
ON OFF AUTO
OPEN
Installation Guide
Summary of the content on the page No. 2
Important Notice It is unlawful in most jurisdictions for a per- son to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the driver's seat, or that is visible directly or indirectly to the operator of the motor vehicle. Please note that the state of Rhode Island forbids the installation of such a device in a motor vehicle.
Summary of the content on the page No. 3
MATERIALS INCLUDED IN THIS PACKAGE: 1) VOH-641 Video Monitor with out TV Tuner / VOH-642 Video Monitor with TV Tuner (1 pc) 2) Accessory Harness (P/N 8010730) (1 pc) 3) 12 Pin Power / Signal harness (P/N 112B2821) (1 pc) 4) 2 Pin Power Wire Harness with choke (P/N 112B2824) (1 pc) 5) RCA “Y” Adapter (1 Male to 2 Female) (P/N 0892165) (1 pc) 6) Hardware Package #4 x 3/8” Screws (12 pcs) #8 x 5/8” Self Drilling Screws (4 pcs) #8 Washers (4 pcs) 7) Remote Control (P/N 1361612 supplied with VOH-642
Summary of the content on the page No. 4
GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, nd Tuner, RF Modulator/external amp, remote headphones, 2 VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting. 4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring as well as all areas where interconnecting w
Summary of the content on the page No. 5
VEHICLE PREPARATION: 1) Locate a constant power source (+12v at all times) and an accessory power source (+12v when key is in the acc. and run positions, and 0v when key is off). Generally, these wires can be found at the ignition switch or fusebox. 2) The mounting method and location will vary from vehicle to vehicle, so this manual will only focus on the installation of the video monitor and related console accessories. 3) Generally, the best location for the video monitor is where the vehicl
Summary of the content on the page No. 6
MINI CONSOLE INSTALLATION: This page only covers special installation considerations for the mini console installation. If the video monitor is to be installed with a custom full sized overhead console, refer to page 3. If the video monitor is to be installed in a vehicle with the mini console (part number 1181300), this console may need to be trimmed to fit the contour of the vehicle headliner. 1) In this installation, the video monitor is mounted directly to the overhead crossmember in the ro
Summary of the content on the page No. 7
MOUNTING THE MINI CONSOLE Roof Roof support Headliner 5"x9"x3/4" Plywood Block (4) #8x1" self drilling screws (not supplied) Mini-Console Video unit (4) #8 Flat washers (not supplied) (4) #8x3/4" self tapping screws (not supplied) -5-
Summary of the content on the page No. 8
Note: cables exiting the pod VOH-641 should be routed as shown. Wireless FM Modulator Antenna Power Harness Red: +12 VDC Item # 3a 4 Mini-Din Connectors (Accessory Cir.) choke Black: Ground Optional Hard Wired FM Modulator Output 21 RCA-Female 12 VDC Power and Ground Left Input Am/Fm LEFT Antenna FM TO WHITE Patch Cord Modulator RIGHT FACTORY 1070610 RED RADIO Dash Radio Right *Refer to Instructions with the RF Input Modulator Kit for further details. RCA-Female To Se
Summary of the content on the page No. 9
Note: cables exiting the pod VOH-642 should be routed as shown. Wireless FM Modulator Antenna Power Harness Red: +12 VDC Item #4 3a Mini-Din Connectors (Accessory Cir.) choke Black: Ground TV antenna Optional Hard Wired FM Modulator Output (If applicable) 21 RCA-Female 12 VDC Power and Ground Left Input Am/Fm LEFT Antenna FM TO WHITE Patch Cord Modulator FACTORY RIGHT 1070610 RED RADIO Right Dash Radio *Refer to Instructions with the RF Input Modulator Kit for furthe
Summary of the content on the page No. 10
CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. To determine which system you have you must locate the wires at the dome light. On a positive switched system, with all the doors closed and the lights out, b
Summary of the content on the page No. 11
Negative Switched Dome lighting Red / black - Lamp on To 12 pin Black / red - Lamp common connector Purple / brown - Lamp Auto on Monitor To constant +12vdc Factory Dome light circuit To constant +12vdc Factory Door ajar switch or Body Control computer Troubleshooting: Remedy: Symptom: -Verify +12 VDC on Red wire at 2 pin Power Harness behind video moni- No power at Video Monitor tor. Verify ground connection with continuity test from known good ground to black wire at 2 pin Power Harness -Ver
Summary of the content on the page No. 12
128-5533C 1999 Audiovox Corp. 150 Marcus Blvd. Hauppauge, NY 11788
