Summary of the content on the page No. 1
Manual
Model 2049
Stereo Compressor
Summary of the content on the page No. 2
Kultube (Model 2049) Manual Version 1.1 – 11/2004 R & D: Ruben Tilgner The information in this document has been carefully verified and is assumed to be correct. However Sound Performance Lab (SPL) reserves the right to modify the product described in this manual at any time. Changes without notice. This document is the property of SPL and may not be copied or repro- duced in any manner, in part or full without the authorization of SPL. Limitations of Liability: In no event will SPL be liabl
Summary of the content on the page No. 3
Content Introduction .............................................................................................. 4 Particular Feature, Equipment ................................................................... 4 Hookup & Security Advices ........................................................................ 5 Power Supply ............................................................................................ 5 Connections Rear Panel/Wiring ................................
Summary of the content on the page No. 4
Introduction The Kultube is an extremely versatile compressor with a broad range of control facilities that cover all typical compressor applications. From improved stereo mixes in the “MIDI Studio“ to surround mastering with several devices connected, all jobs can be undertaken to the highest degree of sound quality. You can, for example, choose between the hard and soft-knee characteristic and insert external devices via a side-chain input for external control. With the unique “Progressiv
Summary of the content on the page No. 5
Hookup & Security Advices Carefully select a place for setting up the Kultube. The unit should be situated away from heat sources and direct sunlight. Avoid installation in environments exposed to vibrations, dust, heat, cold or moisture. Keep the unit away from transformers or motors or any other unit that could generate large variations in power supply or cause electrical interferences. Do not install the unit in proximity to power amplifiers or digital processors. You may consider placin
Summary of the content on the page No. 6
Connections Rear Panel/Wiring 6 The Kultube can optionally be equipped with a 24 bit/96 kHz converter module Further Kultubes Connector for external Connection to console: as slaves in multi- processing units (e. g. Insert Sends > Analog Inputs channel link mode Equalizer) Insert Returns > Analog Outputs 2 1 1 2 Pin wiring XLR Input: Pin wiring XLR Output: Pin wiring Stereo Jack Connector: 3 3 1=GND 2=Hot (+) 3=Cold (-) 1 = GND 2 = Hot (+) 3 = Cold (-) Tip = Hot (+) Ring = Cold (-) Sleeve
Summary of the content on the page No. 7
General Advices Connections Again, while Kultube‘s housing is EMV-proof and protects against HF-interference, placement of the unit is very important since it amplifies microphone signals as well as other unwanted signals. Before connecting the Kultube or any other equipment turn off all power. Adjust the voltage setting on the back so that it corresponds with the power conditions. The following graph shows the correct wiring for connecting unbalanced signals to the balanced XLR connectors
Summary of the content on the page No. 8
Connections Sockets & Rear Switch Sidechain inputs This jack is used as a sidechain input for connecting an external audio signal to control the Kultube (e. g. an equalizer for frequency dependent processing). It is configured as a stereo RCA jack, with the left channel on the tip and the right channel on the ring. Ideally you should use a normal insert cable that combines a stereo RCA plug (connected to the Kultube) and two mono RCA plugs (connected to the control device). When using an e
Summary of the content on the page No. 9
Switches Control Elements Please note also the information on various controls under „Understanding and enjoying the Kultube“ starting page 12. RED/VU This switch changes the VU meter over to Gain Reduction mode. The indicator needle then jumps to the 0 dB value and moves to the left with increasing compression. The scaled values now refer to gain reduction. If the RED/VU switch is not pressed, the VU meter indicates the output level. If neither the RED/VU nor the ACTIVE switch is pressed, t
Summary of the content on the page No. 10
Control Elements Switches Progressive Time Control: ATTACK This function allows to switch in an adjustable automatization of the time constants which is set up with the ATTACK control. Put simply you can now influence the compression intensity for rapid signal increases, or when the function is turned off determine the time until a certain compression level is reached. Progressive Time Control: RELEASE The release times can also be switched to automatic based on the Release control: the latt
Summary of the content on the page No. 11
Controls Control Elements THRESHOLD The Threshold control determines the compressor threshold value. The value scale for the THRESHOLD control indicates the level in dBu. Turning fully CCW provides no control, and fully CW provides compression starting at a level of approx. –40 dBu. RATIO The RATIO control is used to set the ratio between the original signal and the compressed signal. A ratio of 1:4 means that a level increase of 4 dB on the input results in an output change of 1 dB. The mo
Summary of the content on the page No. 12
Control Elements Controls TUBE HARMONICS The TUBE HARMONICS control allows you to drive the tube output stage infi- nitely variable to desperation: the more the control is turned in, the further the tube gets into saturation and the more harmonics are produced. The output level of this stage is automatically adjusted, ti.e. it keeps virtually the same level as the input signal. This allows you to to change the entire sonic behavior of the tubes with just one control. Operating Understanding
Summary of the content on the page No. 13
Understanding and enjoying the Kultube Operating The Ratio control As indicated above, this determines the ratio between the in- and output level above the threshold setting. The preset value specifies how the input dynamics should behave with respect to the output: a ratio of 1 to 2 means that only half of the dynamic change will be present on the output. At 10 dB of dynamics there will only be 5 dB on the output, whereas using a ratio of 1:8 means 10dB becomes just 1.25 dB, etc. In short,
Summary of the content on the page No. 14
Operating Understanding and enjoying the Kultube In the latter case the ratio changes depending on the in0ut signal. As the preset threshold value is approached the ratio is comparatively small (1:1.5) and doesn’t reach the preset maximum value until high input levels are present. The result is much less conspicuous compression, since the process does not kick in as suddenly as with hard-knee mode. On the other hand, hard-knee results in greater loudness and density of the program material.
Summary of the content on the page No. 15
Understanding and enjoying the Kultube Operating Processed in this way, drums get more self assertion and sound ‚faster’. The best setting is not always easy to find, since you usually need to find a compromise. Very fast settings run the risk of producing audible distortions – especially in the case of low frequencies, since the compressor now tries to control each waveform rise. The corresponding control signal assumes a “saw-tooth” form which distorts the audio signal. To suppress thi
Summary of the content on the page No. 16
Operating Understanding and enjoying the Kultube Fig. 5, „Attack PTC“ Fig. 5 shows the control behavior using a sinus burst as an example. In various settings it is clearly to see that the burst signal remains almost unchanged in its form; only the intensity changes. The PTC feature can provide outstanding results not only for percussive signals but also for many other musical signals (vocals, guitar, bass, horns, synthesizers, etc.), since compression is used with the greatest efficienc
Summary of the content on the page No. 17
Understanding and enjoying the Kultube Operating The release parameter is also for the most part responsible for unobtrusive compression. This means it is hard to find the perfect setting as with the Attack control – particularly in the case of complex summed signals a fixed release time may hardly be usable. As with the attack times you must always find a compromise: for very fast and short signal peaks (e.g. drums and percus- sion) you will want to select short release times (100 ms). But
Summary of the content on the page No. 18
Operating Understanding and enjoying the Kultube Fig. 7b AB C Fig. 7c A BC For settings with larger averages the change in the release time is easy to recognize. With very small values the control voltage for the Gain Cell “sticks” to the rectified signal and works almost like an envelope follower. Fig. 8 on the next page shows the various effects of different release time settings on a sinus burst, although the principle is not as easily seen here. These changes are most clearly heard in a
Summary of the content on the page No. 19
Understanding and enjoying the Kultube Operating Fig 8 „Release – PTC“ Using and enjoying the Kultube Applications Summed signal processing The main application area for the Kultube is in stereo summed signal compres- Console: sion together with an analog mixing console. Inserts Send/Return Here the Kultube is looped into the insert paths („Insert Send/Return“). The insert paths are generally in front of the console master fader so that the compressor is driven independent of the master fader
Summary of the content on the page No. 20
Applications Using and enjoying the Kultube Sidechain Use of the SIDECHAIN inputs expands the possibilities for controlling External compression. A typical application is frequency-selective compression, compression control whereby an external equalizer is used to raise the frequencies at which the compressor should respond or to filter out the frequency band you wish the compressor to ignore. Frequency-selective If a summed signal has a lot of bass for example that you want to preserve,
