Summary of the content on the page No. 14
CD1211 REMOTE CONTROL The remote control will allow you to control the basic functions of the CD1211. The remote control sensor is located on the left side of the front panel to the right of the MONO button (18). S AMS = AS/PS VOL PEQ = EQ VOL MOD = MODE LOC = Local/Distant D U BND = BAND LOUD TR. DN TR. UP SCN = Scan, AM, FM BND SCN MOD MUT = LOC AMS PEQ MO = MONO DISP = Clock / Frequency MO MUT DISP PAU SCN RPT 12 3 4 5 6 SHUF DN UP 14
Summary of the content on the page No. 15
CD1211 CARE AND MAINTENANCE CD Player Compact Discs cloth. Wipe in a straight motion from the inside to the outside of the disc. CD-R / CD-RW The following guidelines will help you extend 2. Never use chemicals such as record the life of your CD player: Depending on media type and method of sprays or household cleaners to clean "recording / burning", some CD-R/RWs may be 1. When cleaning the vehicle interior, do not CDs, as they can irreparably damage the incompatible with this unit. Aft
Summary of the content on the page No. 16
CD1211 TROUBLESHOOTING Problem Cause Corrective Action Does not operate (display does not No power to yellow wire; no power to red wire Check connection with test light; check vehicle fuse with test light) light. Inline fuse blown Replace fuse. No power to unit Inline fuse blown Check/replace fuse. Not all speakers operate Incorrect splices or connections Check all splices and connections. Speaker wires shorting to chassis ground or to Check splices; insulate all bare wires. each other Blows fu
Summary of the content on the page No. 17
CD1211 SPECIFICATIONS AM Tuner CEA Power Ratings Tuning range: 530kHz-1710kHz Sensitivity @ 20dB signal to noise: 30uV Frequency response: 50Hz-2kHz., -3dB Auxiliary Input Input sensitivity: 400mV RMS for 1 watt RMS into 4-ohms Frequency response: 20Hz to 20kHz, -3dB Input impedance: 10 k-ohms General Power supply: 11-16 VDC, negative ground Power Antenna (Blue): 500mAmp Max, current Power output: 13 watts RMS X 4 channels into limited protection. 4-ohms @ < 1% THD+N Operating Temp: -10C~60C S
Summary of the content on the page No. 18
Limited Warranty DO NOT RETURN THIS PRODUCT TO THE STORE CD or Multimedia Radios/Headunits Audiovox Electronics Corporation (“the Company”) is committed to Limitations quality and customer service, and are pleased to offer you this THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY Warranty. Please read it thoroughly and contact the Company at 1-800- IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, 323-4815 with any questions. IN NO EVENT, SHALL THE COMPANY'S LIABI
Summary of the content on the page No. 19
Summary of the content on the page No. 20
Audiovox Electronics Corporation 150 Marcus Boulevard Hauppauge, NY 11788 1-800-323-4815 www.audiovox.com ©2007 Audiovox v.083107
Summary of the content on the page No. 1
CD1211
Owner's Manual
AM/FM/CD Receiver
CD1211 CD RECEIVER
MONO
TUNE
EQ
/
AUX IN
SCAN
Summary of the content on the page No. 2
CD1211 PREPARATION Getting Started customer support line at 1-800-323-4815. Disconnect Battery (U.S.A. and Canada only.) Congratulations on your purchase of the Phase Before you begin, disconnect the battery Linear CD1211 Mobile AM/FM/CD Receiver. It’s negative terminal. Tools and Supplies a good idea to read all of the instructions before The following tools and supplies are needed to beginning the installation. We recommend install the radio. having your Phase Linear CD1211 installed by
Summary of the content on the page No. 3
/ MONO CD1211 CD RECEIVER TUNE EQ / SCAN AUX IN CD1211 CD RECEIVER MONO TUNE EQ SCAN AUX IN CD1211 INSTALLATION INSTRUCTIONS This unit is designed for installation in cars, Universal Installation Using trucks and vans with an existing radio opening. Mounting Sleeve In many cases, a special installation kit will be 1. Remove the detachable front panel, if it is required to mount the radio to the dashboard. attached to the chassis, by pushing the These kits are available at electronics supp
Summary of the content on the page No. 4
CD1211 9. Attach one end of the perforated support 2. Install the radio/mounting plate assembly Longer screws may damage components strap (supplied) to the screw stud on the to the sub-dashboard according to the inside the chassis. rear of the chassis using the hex nut instructions in the installation kit. provided. Fasten the other end of the 3. Attach the support strap to the radio and perforated strap to a secure part of the dashboard as described in the Universal dashboard, either above o
Summary of the content on the page No. 5
CD1211 Remove Radio To remove the radio after installation, remove the trim ring by lifting in the center and pulling it off from either side. Insert the removal keys straight back until they lock, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit. Removal Key 5
Summary of the content on the page No. 6
15 CD1211 WIRING 1. Power Antenna (dark blue wire) - Connect 5 to power antenna or amplifier. If not used, tape bare end of wire. 2. Accessory/Ignition (red wire) - Connect to existing radio wire or radio fuse. 3. Ground (black wire) - Connect to ground terminal or clean, unpainted part of chassis. 4. Memory/Battery (yellow wire) - Connect to battery or 12 volt power source that is Dark Blue 1 always live. The radio will not work if this wire is not connected. 5. Antenna Connector - Conn
Summary of the content on the page No. 7
CD1211 OPERATING INSTRUCTIONS Power Select clockwise or counter clockwise to adjust the bass from “-10” to “+10”. “00” represents a flat Press the power button (1) or any other button Press the AUDIO CONTROL button (4) to step response. The bass level is shown on the on the face of the receiver to turn the unit on through the menu of audio functions: volume display for five seconds or until another function when the ignition switch is on. Press the power (VOL), bass (BAS), treble (TRB), ba
Summary of the content on the page No. 8
T T T T C C C C L L L L E E E E E E E E S S S S H H H H S S S S PU PU PU PU CD1211 Balance X-BASS (BAND) Equalizer Selector (EQ) Press the AUDIO CONTROL button (4) four Press and hold the BAND button (5) for two The equalizer function applies preset sound times until “BAL” appears in the display. Within seconds to activate the X-BASS feature. When effects to the unit’s audio output signal. Press five seconds, turn the AUDIO CONTROL (3) listening to music at low volume levels, this EQ (20) t
Summary of the content on the page No. 9
CD1211 CD RECEIVER MONO TUNE EQ / AUX IN SCAN CD1211 Display (D) Front Panel Release that it is correctly engaged, then lightly press the left side of the panel until the mechanism When the unit is off, the LCD displays the time The front panel release button (10) releases the locks it into place. of day. When the unit is on, the LCD mechanism that holds the front panel to the automatically shows the tuner or CD display, chassis. Reset Button depending on which mode of operation is Detachi
Summary of the content on the page No. 10
CD1211 TUNER OPERATION AM/FM Band Selector (BAND) Scan Tuning (SCAN) Preset Stations Press BAND (5) during radio play to switch Press SCAN (15) to scan upwards through all Up to six stations on each band can be stored between three FM bands and one AM band. the strong channels in the current band. The as presets and can then be instantly recalled by “F1”, “F2”, “F3” or “AM” will appear in the unit will pause and play each station for five pressing the associated preset button on the display t
Summary of the content on the page No. 11
CD1211 Repeat for the remaining five presets on the Mono/Stereo Selector (MONO) current band and for all presets on the other Press MONO (18) during FM radio operation to three bands. select stereo reception of the broadcast signal. Under normal reception, the unit should be left Automatically Store / Preset in the stereo mode as indicated by the “ST” Scan (AS/PS) designation and the associated signal strength Automatically Store indicator that appear on the display panel when Select six
Summary of the content on the page No. 12
CD1211 CD PLAYER OPERATION Insert CD During either function, the elapsed time will Disc Scan (SCN) appear on the display. Release the button to With the label surface facing up, gently insert During disc play, press SCN (24) to play the resume CD play. the disc into the CD slot (21) until the soft- first 10 seconds of each track on the disc. “S-- loading mechanism engages and pulls the disc SCN” will appear in the display. When the Play/Pause in. Disc play begins, “CDP PLAY” will appear in de
Summary of the content on the page No. 13
CD1211 Disc Repeat (RPT) CD Player Error Codes Press RPT (25) during disc play to continuously If a problem should develop while operating the repeat the selected track. “S--RPT” will appear CD player, an error code (ER-1, ER-2, etc.) in the display. Press RPT again to stop may appear on the display panel. This can repeating. “S--RPT” will disappear from the indicate a number of problems with the unit, display, and regular play will resume. The including a mechanical error or an error in the
