Summary of the content on the page No. 1
Accessory Application Publications No.
AII 27936
CD CHANGER
INSTALLATION
2002-2005 CIVIC SI
Issue Date
ATTACHMENT KIT
INSTRUCTIONS
AUG 2004
PARTS LIST
3 EPT seals
CD Changer Attachment Kit (sold separately):
P/N 08B26-S5T-100
4 Cushion tapes
CD changer bracket
8 Cap nuts, 6 mm
4 Washer-screws, 4 x 8 mm
2 CD changer plates
4 Clip-nuts, 6 mm
Template A
4 Stepped bolts, 6 mm
Template B
Left side bracket
Right side bracket
Bus cable
13 Wire ties
08B26-S5T-1000-91
© 2004 American Honda Motor Co., Inc
Summary of the content on the page No. 2
6-Disc CD Changer (sold separately): Illustration of the CD Changer Installed in the Vehicle P/N 08A26-1B1-100 CD changer BUS CABLE CD CHANGER 4 Washer-screws, 4 x 6 mm (Not used) Adhesive seal sheet AUDIO UNIT Cover plates INSTALLATION CD magazine Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add Owner’s Manual equipment to your vehicle. These proce
Summary of the content on the page No. 3
4. Remove the driver's dashboard lower cover. Turn 6. Remove the shift lever trim: the lock knob 90° counterclockwise. Gently pull down on the left side of the cover to release the Pull the shift boot down, and remove the shift two hooks, then pull down on the cover to release knob by turning it counterclockwise. the three retaining tabs. Take care not to damage the retaining tabs. � Reach through the shift boot, and gently pull out on the shift lever trim to release the bottom of the trim. Li
Summary of the content on the page No. 4
7. Remove the vehicle harness clip from the center 9. Remove the dashboard center lower cover, and panel bracket by pushing up on the locking tab on disconnect the accessory power socket connector. the clip and pulling the clip out toward you. Remove the two self-tapping screws from the back of the front center console. SELF-TAPPING SCREW CENTER PANEL BRACKET Push on the locking tab. VEHICLE CLIP HARNESS DASHBOARD CENTER FRONT CENTER 8. Reach through the glove box area, and loosen the LOWER COVE
Summary of the content on the page No. 5
11. Remove the front center console: 13. Turn over the cargo area mat, and remove the cargo area floor. Slide the front seat completely rearward. CARGO AREA MAT Open the lid, and take out the console box mat. Remove the two bolts from the inside of the pocket. CARGO AREA Remove the two clips, then slide the front FLOOR center console to the rear to release the four retaining tabs. Take care not to damage the retaining tabs. CONSOLE BOX MAT CLIP RETAINING TAB BOLT 14. Remove the cargo are
Summary of the content on the page No. 6
15. Remove the rear seat cushion bolt, and remove 20. Remove the left rear seat-back center hinge (one the rear seat cushion by lifting the rear of the bolt). LEFT REAR cushion to release the hooks and then pulling it SEAT-BACK CLIP LEFT REAR toward you. SIDE PANEL FLOOR TRIM SEAT- CARPET BACK CENTER REAR HINGE SEAT CUSHION 2 1 CLIP LEFT PIN BOLT 22 N·m (16 lb-ft) HOOK BOLT 21. Remove the clip from the floor panel behind the seat-back. HOOK 22. Release the seat-back pin from the left rear side 1
Summary of the content on the page No. 7
24. Remove the left rear bulkhead cover: 26. Remove the left rear seat belt lower anchor bolt. Remove the clip from the left rear bulkhead 27. Remove the rear trim panel (three clips and two cover. Take care not to damage the clip. hooks). Gently pry the left rear bulkhead cover away CLIP from the left rear side trim panel by inserting the end of a flat-tip screwdriver wrapped in a shop towel into the groove of the left rear bulkhead cover. Pry up on the seven retaining tabs, and remove th
Summary of the content on the page No. 8
33. Position template B on the air outlet area of the left 30. Get template A from the kit. Tape the template to rear side trim panel, and tape it in place using the left rear side trim panel in the area shown, and strips of masking tape. Using a pushpin, mark the tape it in place using strips of masking tape. Using trim panel at each of the four marked points on a pushpin, mark the trim panel at each of the five the template. Remove template B. marked points on the template. Remove LEFT REAR SI
Summary of the content on the page No. 9
35. Slide the four 6 mm clip nuts onto the left rear 38. Insert the studs of the two CD changer plates into side trim panel through the 10 mm holes you just the 7.5 mm holes (made in step 31) from the back. made. CD CHANGER 6 mm STEPPED BRACKET BOLT 6 mm CLIP NUT 6 mm CAP 6 mm CAP NUT LEFT REAR NUT SIDE TRIM PANEL (AIR OUTLET AREA) CD CHANGER PLATE 39. Insert the studs of the CD changer plate into the holes in the CD changer bracket, and install a 36. Using scissors, cut 1/4 piece from one of th
Summary of the content on the page No. 10
42. Visually check the position of the spring adjusting 45. Secure the CD changer bus cable connector to the pins on both sides of the CD changer. If both of the CD changer with the remaining 3/4 piece of the spring adjusting pins are not in the horizontal (H) EPT seal cut in step 36. position, move the pins to the horizontal (H) position by sliding them up with an awl. EPT SEAL (Remaining piece of the EPT seal cut in SPRING ADJUSTING PIN step 36) (H: HORIZONTAL POSITION) LOCKING COVER CD CHANGE
Summary of the content on the page No. 11
Routing the Bus Cable 50. Route the bus cable from the side panel to the center of the floor panel along the floor cross 48. From the back of the left rear side trim panel, route member as shown. the bus cable as shown. Secure the bus cable to the fuel fill door opener cable with two wire ties in CUSHION TAPE the areas shown. Do not secure the bus cable to the clear washer tube. BUS CABLE WIRE TIE Do not secure the bus cable to the clear washer tube. FLOOR PANEL WIRE TIE BUS BUS CABLE CABLE FLOO
Summary of the content on the page No. 12
53. Route the bus cable so that its connector is 55. Near the parking brake lever, secure the bus cable about 50 mm farther than the vehicle 20-pin to the vehicle harness with three wire ties in the connector. Secure the bus cable to the vehicle areas shown. harness with two wires in the areas shown. WIRE TIE BUS CABLE BUS CABLE CONNECTOR VEHICLE VEHICLE 20-PIN HARNESS CONNECTOR WIRE TIE About 50 mm 56. Loop the excess bus cable at the floor cross member, and secure it to the vehicle harness wit
Summary of the content on the page No. 13
Installing the Center Panel/Radio Unit 58. While holding the center panel with the radio unit installed near the center panel opening, plug the 57. Check that the vehicle harnesses are not pinched vehicle 20-pin connector, the antenna lead, the by the stays. heater control harness connector, and the bus cable connector into the rear of the radio unit. VEHICLE HARNESS ANTENNA LEAD CENTER PANEL STAY STAY VEHICLE CONNECTOR BUS CABLE CONNECTOR BOLT (Tighten after installing the ANTENNA center panel.
Summary of the content on the page No. 14
60. Check that all wire harnesses are routed properly and all connectors are plugged in. 61. Reconnect the negative cable to the battery, and set the clock. 62. Enter the customer’s radio anti-theft code, and reset the radio station presets. 63. Check the operation of the CD changer according to the Owner’s Manual. 64. Put the CD changer Owner’s Manual and the shipping clips retained in step 41 in the glove box. 65. Reinstall all removed parts. 66. Do the engine control module (ECM) idle learn p
